Hitachi DH25PB - 31/32" SDS-plus Shank Rotary Hammer Support and Manuals
Get Help and Manuals for this Hitachi item
This item is in your list!
View All Support Options Below
Free Hitachi DH25PB manuals!
Problems with Hitachi DH25PB?
Ask a Question
Free Hitachi DH25PB manuals!
Problems with Hitachi DH25PB?
Ask a Question
Popular Hitachi DH25PB Manual Pages
Instruction Manual - Page 5
...moving parts, breakage of unauthorized parts or failure to a stable platform. Follow instructions in a risk of this manual. Dust...designed. (3) Do not use only identical replacement parts. Service (1) Tool service must be repaired. (4) Disconnect the plug form the power...support the workpiece to follow Maintenance Instruction may lead to control. (7) Check for your application.
Instruction Manual - Page 6
...Instruction Manual. 10. The tool's motor air vent must be used until repaired...SPECIFIC SAFETY RULES AND SYMBOLS
1. ALWAYS wear ear protectors when using the tool for applications other than those specified. ALWAYS attach the side handle and securely grip the Rotary Hammer...NEVER touch moving parts. 7.
NEVER operate... sure to replace the guard ... maintenance or servicing requires the ...
Instruction Manual - Page 8
... normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments. Never use solvents, gasoline or thinners on the nameplate. English
DOUBLE INSULATION FOR SAFER OPERATION
To ensure safer operation of this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of the...
Instruction Manual - Page 11
... dust cup with this rotary hammer. ⅜ Installing dust collector (B) When using a rotary hammer for upward drilling operations attach a dust cup or dust collector (B) to collect dust or particles for
exclusive use of concrete drilling work .
ⅷ Insert dust collector (B) completely into the
chuck part of the arrow and pull out the drill bit. 7. Selecting the driver bit Screw heads...
Instruction Manual - Page 12
... iron reinforcing rod, the bit will stop immediately and the rotary hammer will react to revolve. Installing drill chuck and chuck adaptor (Fig. 8):
(1) Mount the drill chuck to the chuck adaptor.
(2) The part of the SDS-plus shank Fig. 8 The power switch should also be set to rotation only mode by turning the change lever fully counterclockwise...
Instruction Manual - Page 13
...force will deteriorate the tip edge of the drill bit and reduce the service life of the
rotary hammer in addition. ⅷ Drill bit may be damaged by excessive force.
Should...screws (Fig. 9) (1) Selecting a suitable driver bit
Employ phillips screws, if possible, since the driver bit easily slips off while disengaging the rotary hammer from the jammed hole.
English
CAUTION:
...
Instruction Manual - Page 14
...handle Fig. 10
(1) Mount the taper shank adaptor to the rotary
hammer. (Fig. 11) (2) Mount the drill bit (taper shank) to the taper
Front cap Grip
shank adaptor. (Fig. 11...Drill bit
prescribed depth.
(4) To remove the drill bit (taper shank), insert the cotter into the slot of the taper shank adaptor and strike the head of the cotter with
Taper shank adaptor
a manual hammer supporting...
Instruction Manual - Page 15
...spring is installed in reduced service life of excessive force will not only expedite the work, but will establish. Fig. 16
(4) Application of the rotary hammer.
15 Push it stops.
(4) Engage the guide plate with...to the rotary hammer. (Fig. 14)
(3) Insert the center pin into the guide plate until it
lightly to the core bit shank. (Fig. 13) Lubricate the thread of the drill bit, ...
Instruction Manual - Page 16
... pin and the guide plate, turn OFF the switch and disconnect the plug form the receptacle.
3. Core bit shank
Fig. 17
16 Dismounting. (Fig. 17) Remove the core bit shank from the rotary hammer and strike the head of the core bit shank strongly two or three times with the manual hammer holding the core...
Instruction Manual - Page 17
...of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is... CAUTION:
Using this rotary hammer with a carbon brush which have the same carbon brush Nos.
shown in excess of carbon brush
21
-
70
Fig. 18
NOTE: Use HITACHI carbon brush No.
indicated in motor trouble. When they slide ...
Instruction Manual - Page 18
...)
(2) Supply 17.5g (the standard volume to install the tail cover with securely tightening two set screws and remove the tail cover. Therefore, the machine can be used , all service and repairs must be used without lubrication for long periods. Proceed for grease replacement at the nearest HITACHI Authorized Service Center. When the supplied grease tube is...
Parts List - Page 1
parts list product(parts list) kensaku
1/9
Hitachi Power Tools
LIST NO. O
40
70 71
61
44
0
89 90
93
78
67
http://denei2.hitachi-koki.cojp/epower4/print_out.php
2004/07/23 E454
ELECTRIC TOOL PARTS LIST
■ HAMMER DRILL Model DH 25PB
2003 • 6 • 1 (E1-3)
2 15
17 18 19
21
23 3
•41..".
Parts List - Page 7
... (SDS PLUS) NO.2
661 944-477 COTTER
662 303-332 HAMMER DRILL CHUCK SET 13MM
663 303-334 CHUCK HANDLE
664 303-335 RUBBER CAP
665
302-976
ANCHOR SETTING ADAPTER A (SDS+) W1/4X260L
666
302-975
ANCHOR SETTING ADAPTER A(SDS+) W5/16X260L
667
303-621
ANCHOR SETTING ADAPTER A (SDS+) W3/8X160L
668
302-974
ANCHOR...
Parts List - Page 8
parts list product(parts list) kensaku
675
971-796
"ANCHOR SETTING ADAPTER A W3/8- (MANUAL
676
971-797
"ANCHOR SETTING ADAPTER A W1/2- (MANUAL
677
971-798
- ANCHOR SETTING ADAPTER A W5/8- (MANUAL
678
971-799
"ANCHOR SETTING ADAPTER B W1/4- (MANUAL
679
971-800
- ANCHOR SETTING ADAPTER B W5/16- (MANUA
680
971-801
- ANCHOR SETTING ADAPTER B W3/8- (MANUAL
681
971-802
"ANCHOR ...
Parts List - Page 9
parts list product(parts list) kensaku
705 II 982-693 (GUIDE PLATE (FOR CORE BIT 90MM) 706 982-684 CENTER PIN ...'Y 713 306-910 SOCKET ADAPTER (B) 714 981-840 GREASE (A) FOR HAMMER.HAMMER DRILL (30G) 715 308-471 GREASE FOR HAMMER.HAMMER DRILL (70G) 716 980-927 GREASE FOR HAMMER.HAMMER DRILL (500G)
9/9
1 1 1 1 1 1 1 INCLUD.713 1 1 1 1
http://denei2.hitachi-koki.cojp/epower4/print_out.php
2004/07/23
Hitachi DH25PB Reviews
Do you have an experience with the Hitachi DH25PB that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hitachi yet.
Earn 750 points for your review!