Instruction Manual
Page 10
Drill Chuck Capacity 3/8" (10mm) 1/2" (13mm) Electric Brake No No Yes... lbs(2.1kg) 4.6 lbs(2.1kg) 4.0 lbs(1.8kg) 4.2 lbs(1.9kg) 4.4 lbs(2.0kg) - Model D13VF D13VG Speed of Angle Unit LOW(650/min.) HIGH(1350/min.) LOW(400/min) HIGH(900/min.) Steel Twist Bit 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) Hole Saw ...2-1/2"(64mm) 4-1/2"(114mm) 4"(102mm) 10 English SPECIFICATIONS Model D10VF D10VG D13VF D13VG Motor Single Phase, Series Commutator Motor Power Source Single Phase 120V AC 60 Hz Current 9.0A No-Load Speed 0-3000/min. 0-1200/min. 0-850/min. 0-600/min.
Drill Chuck Capacity 3/8" (10mm) 1/2" (13mm) Electric Brake No No Yes... lbs(2.1kg) 4.6 lbs(2.1kg) 4.0 lbs(1.8kg) 4.2 lbs(1.9kg) 4.4 lbs(2.0kg) - Model D13VF D13VG Speed of Angle Unit LOW(650/min.) HIGH(1350/min.) LOW(400/min) HIGH(900/min.) Steel Twist Bit 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) Hole Saw ...2-1/2"(64mm) 4-1/2"(114mm) 4"(102mm) 10 English SPECIFICATIONS Model D10VF D10VG D13VF D13VG Motor Single Phase, Series Commutator Motor Power Source Single Phase 120V AC 60 Hz Current 9.0A No-Load Speed 0-3000/min. 0-1200/min. 0-850/min. 0-600/min.
Instruction Manual
Page 13
...sleeve by clamping bolts. Bar Wrench Locking Screw Loosen Fig. 7 Angle Unit Joint Sleeve Coupling Clamping Bolt Fig. 8 Low Speed Fig. 9 High Speed Fig. 10 13 And hold the drill so that only the chuck rests firmly and squarely on the edge of the joint sleeve, and turn out the locking...bench. This should loosen the chuck from the spindle which can be removed by striking the wrench, don't strike the wrench forcibly and send the drill to a HITACHI AUTHORIZED SERVICE CENTER. (2) Attaching the angle unit. ⅜ After removing the chuck, engage the coupling to remove the chuck by only a ...
...sleeve by clamping bolts. Bar Wrench Locking Screw Loosen Fig. 7 Angle Unit Joint Sleeve Coupling Clamping Bolt Fig. 8 Low Speed Fig. 9 High Speed Fig. 10 13 And hold the drill so that only the chuck rests firmly and squarely on the edge of the joint sleeve, and turn out the locking...bench. This should loosen the chuck from the spindle which can be removed by striking the wrench, don't strike the wrench forcibly and send the drill to a HITACHI AUTHORIZED SERVICE CENTER. (2) Attaching the angle unit. ⅜ After removing the chuck, engage the coupling to remove the chuck by only a ...
Instruction Manual
Page 15
... immediate stopping. The power switch should also be applied for continuous running. To maintain firm control, establish a good foothold, use side handle, hold the drill securely. ⅷ When the brake becomes ineffective, send the tool to turn the switch off during a work break and after work and start again. Speed is low when the trigger...
... immediate stopping. The power switch should also be applied for continuous running. To maintain firm control, establish a good foothold, use side handle, hold the drill securely. ⅷ When the brake becomes ineffective, send the tool to turn the switch off during a work break and after work and start again. Speed is low when the trigger...