Hitachi 937913Z - Wrench Spanner For G18MR Support and Manuals
Get Help and Manuals for this Hitachi item
This item is in your list!
View All Support Options Below
Free Hitachi 937913Z manuals!
Problems with Hitachi 937913Z?
Ask a Question
Free Hitachi 937913Z manuals!
Problems with Hitachi 937913Z?
Ask a Question
Popular Hitachi 937913Z Manual Pages
Instruction Manual - Page 3
... before operating or maintaining this power tool. NEVER use this power tool in this Instruction Manual and in death or serious injury. NOTE emphasizes essential information.
3 English
IMPORTANT SAFETY INFORMATION
Read and understand all of this Instruction Manual. Basic safety precautions are caused by HITACHI. Most accidents that has not been specifically recommended by the failure...
Instruction Manual - Page 4
...power tool outside, use and reduce the risk of drugs, alcohol, or medication. Personal Safety (1) Stay alert, watch what you to follow all instructions. English
SAFETY
GENERAL SAFETY RULES
WARNING: Read and understand all instructions...grounded. (3) Don't expose power tools to install a polarized outlet. Do not change the plug in moving parts. Replace damaged cords immediately. These ...
Instruction Manual - Page 5
... overreach. Proper footing and balance enables better control of the tool in the Maintenance section of this manual. Holding the work by unqualified personnel could result in the hands of untrained users. (6) Maintain tools with another tool.
5. Service (1) Tool service must be repaired. (4) Disconnect the plug form the power source before using. Dust mask, non-skid safety shoes, hard...
Instruction Manual - Page 6
... wheel (see SPECIFICATIONS at least the speed recommended on the tool warning label. NEVER operate without all guards in the Instruction Manual.
6 Use right tool. don't use tool for purpose not intended -for cutting tree limbs or logs.
9. Wheels and other body parts near the tool's moving parts. Don't use circular saw for example- NEVER use a power tool for applications other...
Instruction Manual - Page 7
... by a Hitachi authorized service center.
17. Check their condition periodically.
12. If using it may damage and crack plastic parts. Carefully handle power tools. Solvents such as where flammable materials or gases are present.
22. Do not wipe them with soapy water and dry thoroughly.
20. NEVER allow the tool to the tool. Check for repairs by the...
Instruction Manual - Page 8
... physically separated insulation systems have a trial run before grinding commence (see "Test the grinder before
using the power tool in this manual when replacing the depressed
center wheel. 28. ALWAYS follow the instructions contained in this Instruction Manual, including not using " on this power tool, HITACHI has adopted a double insulation design. Comfirm if there are going to the...
Instruction Manual - Page 10
... Some illustrations in this Instruction Manual may show details or attachments that differ from those on the tool unless you in the safe operation and maintenance of the power tool.
NAME OF PARTS
Push Button Gear Cover
Housing
Handle
Packing Gland
Switch Brush Cover
Depressed Center Wheel
Side Handle Wheel Guard
SPECIFICATIONS
Model Motor Power Source Current No-Load...
Instruction Manual - Page 11
... work area is in the OFF position. WARNING: Damaged cord must be replaced or repaired.
4. Check the receptacle If the receptacle only loosely accepts the plug, the receptacle must be repaired. If such a fautly receptacle is in the ON position, the power tool will start operating immediately and can cause serious injury.
3. To avoid such...
Instruction Manual - Page 12
... wheel piece.
[Installing and adjusting the wheel guard] ⅜ Open the lever and insert the locating pin
Screw Set Piece
of wheel guard...and packing ground are wearing eye protection. Duration of this manual for use it into line with
the across flats of packing...Wheel Guard
aligned (the position where the wheel
guard is replaced 3 minutes or more When starting daily work , test ...
Instruction Manual - Page 15
...are fully tightened. Wear limit
No. Check that they are consumable parts. Confirm that there is a crack or a transformation in the wheel, replace it becomes worn to its wear limit. If there is no ... Use HITACHI carbon brush No. 61 indicated in the wheel guard, the electrical cord and the housing, etc.
Using cracked, deformed or damaged wheels can lead to switch power OFF and...
Instruction Manual - Page 16
Service parts list A: Item No. This Parts List will be helpful if presented with the tool to incorporate the latest technological advancements.
Service and repairs All quality power tools will be used, all service and repairs must be changed without prior notice.
16 Used D: Remarks
CAUTION: G Repair, modification and inspection of Hitachi Power Tools must be carried out by a HITACHI ...
Parts List - Page 1
Hitachi Power Tools
LIST NO. E266
ELECTRIC TOOL PARTS LIST
DISC GRINDER Model G 18MR
2004 • 2 • 20 (E1)
1
2 3
4
5
6 7
8
18
9
10
11
19
12
13 41
42
20
43
21
22
23 44
24
45
25
46
26
501
14
47 48
502
15 16 17
27
28 29 30 31 32
33 34 35 36 37 38
39
52 48 49
53 49 50
53 54
49 50 51 49
55 56
59
60 61 62
58 57
40
63
Parts List - Page 3
... 999-089 CARBON BRUSH (AUTO STOP TYPE) (1 PAIR) 1 FOR NZL, EUROPE
51 322-546 HANDLE (B)
1
52
HITACHI LABEL
1
53 322-323 BRUSH HOLDER SET
2
54 946-362 BEARING LOCK
1
* 55 320-239 SWITCH (2P PILLAR TYPE) W/SAFETY LOCK 1 OFF/ON LOCK... TPE
* 63 500-435Z CORD
1 (CORD ARMOR D8.2) FOR HKG
2 -- 04
* ALTERNATIVE PARTS
--- 3 --- PARTS
ITEM NO. CODE NO.
42 306-890
LOCK PIN
DESCRIPTION
NO.
Parts List - Page 4
... HANDLE
* 604 937-960Z WHEEL GUARD
1 FOR USA, CAN
* 605 937-911 SET RING (A)
1 FOR USA, CAN
* 606 949-656 HEX. BOLT M8X20 (10 PCS.) 2 FOR USA, CAN
* 607 949-457 SPRING WASHER M8 (10 PCS.)
2 FOR USA, CAN
--- 4 ---
* ALTERNATIVE PARTS
Printed in Japan 2 -- 04 (040220N) DESCRIPTION
501 937-913Z WRENCH
* 502...
Specifications - Page 1
Couper Ici / Please Cut Here
Use Genuine Hitachi Grinding Wheels
G18MR Please Cut Here / S.V.P.
S.V.P. Features "IDI" (Internal Double Insulation) technology. 3 - position side handle that reduces vibration. Couper Ici
7" Disc Grinder
G18MR
Specifications
>> AMP: >> Wheel Dia.: >> Spindle: >> Weight: >> RPM:
15 7" 5/8-11" 11.9 lbs. 6,000
Standard Accessories
>> Wheel ...
Hitachi 937913Z Reviews
Do you have an experience with the Hitachi 937913Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hitachi yet.
Earn 750 points for your review!