Hayward SP2610X15XE Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward SP2610X15XE manuals!
Problems with Hayward SP2610X15XE?
Ask a Question
Free Hayward SP2610X15XE manuals!
Problems with Hayward SP2610X15XE?
Ask a Question
Hayward SP2610X15XE Videos
Hayward Super Pump XE Canada, Hayward Tristar XE www.poolproductscanada.ca SP2610X15XE SP3210X15XE
Duration: 1:46
Total Views: 191
Duration: 1:46
Total Views: 191
Popular Hayward SP2610X15XE Manual Pages
XE Pumps Technical Training Guide - Page 3
... 25-27
Pg. 28-37
29-34 30 31 32 33 34 35 36 36 37
Pg. 38-47
39-41
42-44 45-47
3 Install XE Series Pump 2. MaxFlo XL Model 8. Super Pump Model
Troubleshooting Guide
1. TriStar XE (Exploded View and Parts List) 2. Replace Shaft Seal - Enable/Disable Priming Mode 5. MaxFlo XL XE (Exploded View and...
XE Pumps Technical Training Guide - Page 17
... for three (3) hours then resume normal operation according to the daily schedule. To enter manual override mode follow the steps below:
Scan QR Code for access to Quick
Start Guide
Step 1
Step 2
Press and release once
During normal operation, while the LED is solid, press and release the button one (1) time to Step...
XE Pumps Technical Training Guide - Page 18
... rapidly and then go to step 6.
Step 5
1x
*Once a speed has been selected the pump will remain in manual override for three (3) hours. See reasons on pg. 17 of this manual. To cancel manual override go solid indicating normal operation has resumed.
18
*When STOP is selected pump will remain in stopped until...
XE Pumps Technical Training Guide - Page 29
... too high IPM temperature too high Pump has stalled Internal motor/drive failure
29
After troubleshooting the indicated system error, it can communicate errors through the LED indicator around the button. 1: Troubleshooting: System Errors
During normal operation (not programming mode), the XE pump can be manually reset by pressing and releasing the button once when the...
XE Pumps Technical Training Guide - Page 36
... off for parts list. Check pages 38-47 of binding issues. If no issues are found . If motor still will not start replace the power end.
If motor still will not start replace the power end. If not within 10% of applied voltage. Correct any evidence of this manual for 30 seconds. 3: Troubleshooting: Motor Shuts...
XE Pumps Technical Training Guide - Page 41
...
Part #
SPX3200Z3 SPX3200Z5PAK4
SPX4000FG SPX3200S SPX3200GA SPX3207X10XEPE SPX3210X15XEPE SPX3215X20XEPE SPX3200Z211 SPX3200WF SPX3200SR SPX3200Q2 SPX3200SA SPX4000SAV
Description
Housing Bolt Motor Bolt (package of 4) Drain Plug w/ O-ring Kit
Strainer O-ring Motor Support ... Riser (aligns w/ Sta-Rite® model pumps) Motor Support Adapter Shaft Seal Assembly Shaft Seal Assembly (Viton)
41
XE Pump Series - Owners Manual - Page 1
...'s Manual
Contents
Pump Warnings 2 Overview 5 Installation 6 Operation 9 Troubleshooting............14 Maintenance 15 Winterization 16 Shaft Seal Change.........17 Replacement Parts........20
TriStar® XE MaxFlo® XE Super Pump® XE
Hayward Pool Products 1415 Vantage Park Dr., Suite 400
Charlotte, NC 28203 Phone (908)-355-7995
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT...
XE Pump Series - Owners Manual - Page 2
... hazard. All electrical wiring MUST be installed and serviced only by a qualified professional. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. To reduce...installed pool is constructed in or on your equipment or in a building such that will or can cause severe injury and/or death. SAVE THESE INSTRUCTIONS
2
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
XE Pump Series - Owners Manual - Page 3
...Code (NEC). Such a GFCI should be provided by the installer and should be
inspected frequently and replaced at least every ten years, or if found to operate in this pump. If the GFCI fails to be tested on the pump housing and to all metal parts...have the problem corrected by a GFCI. There is protected by a qualified service representative before using. To reduce the risk of Electric...
XE Pump Series - Owners Manual - Page 4
...for burns. Hazardous Pressure. Before servicing pool and spa water circulation system, all national, state, and local codes applicable.
• Installation of three feet (3') [0.91 ...manual air relief valve until a steady stream of Entrapment Hazards:
• When outlets are not properly iso-
WARNING - WARNING -
SAVE THESE INSTRUCTIONS
4
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
XE Pump Series - Owners Manual - Page 6
...rains. Secure pump to base with local codes. sure. Suction lines should have continuous ... recommended to set the maximum speed ...servicing pump and piping.
Pump motors require free circulation of a swimming pool filtration system operate under pres- WARNING - Do NOT install pump and filter in severe personal injury or death.
6 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Incorrectly installed...
XE Pump Series - Owners Manual - Page 10
...0%
STOP
Normal Operation - Interval 3 Press & Hold Confirmation System Errors
LED Behavior Solid Green Slow Flashing ON/OFF Quick Flashing - When...the pump. Operating Mode or Status Normal Operation Manual Override Programming - The default schedule from the ...schedule as power is pressed.
10
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Interval 2 Programming - This 24 hour schedule is...
XE Pump Series - Owners Manual - Page 14
...self-prime after certain
conditions.
The most common application may be disabled by setting all Interval speeds the same and have the pool control power it will only...by automation controls using a pool pump timer, program your specific pool control's manual for these wiring instructions.
14 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS To enable, press and hold again for wiring information. ...
XE Pump Series - Owners Manual - Page 16
... Hayward Technical Service at the terminal block, and that motor current is set
correctly for obstructions and cleared if present. Do not purge the system with genuine Hayward seal assembly kit.
To avoid dangerous or fatal electrical shock hazard, turn OFF power to freeze with water in a dry area.
16 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS System Errors...
XE Pump Series - Owners Manual - Page 17
... all recesses & parts to the motor, using the four (4) 3/8" x 1" bolts, and re-attach the motor support to follow instructions may result in the seal plate prior to mounting the motor to pump before beginning shaft seal replacement.
• Only qualified personnel should always be reassembled. Inspect gaskets & replace if necessary. Seal Installation 7. Replacing the Impeller and...
Hayward SP2610X15XE Reviews
We have not received any reviews for Hayward yet.