Harbor Freight Tools 69927 - 21° Angle Framing Nailer Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 69927 manuals!
Problems with Harbor Freight Tools 69927?
Ask a Question
Free Harbor Freight Tools 69927 manuals!
Problems with Harbor Freight Tools 69927?
Ask a Question
Popular Harbor Freight Tools 69927 Manual Pages
User Manual - Page 2
... WARNING marking concerning Risk of Contents
Safety 2 Specifications 7 Setup 8 Operation 11
Maintenance 14 Parts List and Diagram 18 Warranty 20
SAFETY
SETUP
OPERATION
WARNING SYMBOLS AND DEFINITIONS This is used ... goggles with side shields.
It is the safety alert symbol.
Read the manual before set-up and/or use. Wear NIOSH‑approved dust mask/respirator.
Symbol
...
User Manual - Page 4
...repaired. A tool is dangerous and must be controlled with the trigger is dangerous in the Specifications chart of binding and is damaged. g.
Tool service must not be used in a risk of injury to persons.
Always verify prior to result in this tool. SAVE THESE INSTRUCTIONS... identical replacement parts. Never use with the specific tool model, increases the risk of parts, and...
User Manual - Page 5
...SETUP
Specific Safety Instructions
1. Always assume the tool contains fasteners.
5. No horseplay. Do not remove, tamper with, or otherwise cause the tool operating controls to a new location.
13. Disconnect the tool from head and body. Moving the tool to become inoperable.
11. Refer to the tool maintenance instructions...or repair. Unattended...manual for triggering options.
4. Install...
User Manual - Page 6
...SETUP
OPERATION
MAINTENANCE
Page 6
For technical questions, please call 1-800-444-3353. Nicotine reduces the blood supply to ensure medical problems are not being caused or worsened from use. Let the tool do the work .
6. SAVE THESE INSTRUCTIONS...each day of vibration-related injury.
3. Do not smoke during use this manual. Grip tool as lightly as explained in this tool. To reduce the ...
User Manual - Page 7
...69927 69928
For technical questions, please call 1-800-444-3353. Page 7
SAFETY
Functional Description
Specifications
Model Maximum Air Pressure Air Inlet Air Consumption Safety Mechanism Type
Nail Type
69927
120 PSI
1/4″..., 28° Angle, Paper Collated Clipped Head
Air Inlet
SETUP
OPERATION
MAINTENANCE
Magazine
Depth Adjustment
Screw
Safety Nosepiece
Pusher
Safety Nosepiece -
User Manual - Page 8
...and quick coupler for best service, as shown on Figure ...setting must not exceed job site regulations/restrictions. Repair any residual air pressure, and release the trigger to allow the air tool to set...parts listed in a safe fashion after the tool is disconnected and unpowered.
SAFETY
SETUP
Initial Tool Set... this manual including all text under subheadings therein before set up ...
User Manual - Page 11
...to the tool and set up or use of this manual including all text under subheadings therein before use tool until repaired. If it fails to a qualified service technician.
7.
There ... Set Up
1.
Squeeze the Trigger.
The tool should return to allow access by a qualified service technician. If any problems are found, do not use , looking for damaged, loose, and missing parts....
User Manual - Page 12
...tool and set within the Operating Air Pressure indicated on the Specification chart.
...setting
to enable contact trip / bump fire operation. SAFETY
SETUP
Contact Safety Trip (Bump Fire) Mechanism Definition
The contact safety trip (or bump fire) mechanism allows rapid fire. Contact safety trip / bump fire should use proper, safe work practices
should only be used by a qualified service...
User Manual - Page 13
...SETUP
OPERATION
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with clean, dry cloth. Pull Pusher all the way to ensure that it against the workpiece.
4. General Operating Instructions...fire one fastener, move and push safety nosepiece again to setting.
g.
Loosen the Depth Adjustment Screw, adjust the Safety ...
User Manual - Page 14
...-Maintenance Instructions
Procedures not specifically explained in this manual must also...service. Maintain the lubricator's oil level.
Drain the moisture filter regularly.
Lubricate the air inlet using only white lithium grease. SETUP
OPERATION
MAINTENANCE
Page 14
For technical questions, please call 1-800-444-3353. Other lubricants may damage the mechanism and may cause parts...
User Manual - Page 15
...
Use a screwdriver to the tool if reused.
4. SETUP
OPERATION
MAINTENANCE
Item 69927 69928
For technical questions, please call...TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams):
• Wear ANSI-approved ... it open during service.
If a fastener is likely bent or damaged and may cause parts or a fastener to...
User Manual - Page 16
...SETUP
Troubleshooting
Problem
Insufficient fastener depth.
Incorrect lubrication or not enough lubrication.
4. Magazine dirty or not
lubricated properly. 5. Likely Solutions
1. Check for incorrect alignment and uneven gaps. If cross-threaded, disassemble and replace damaged parts before service.
Incorrect tool depth setting...
Clearing Jams instructions. 2. Fasteners...
User Manual - Page 17
... are not available individually as replacement parts. SETUP
OPERATION
MAINTENANCE
Item 69927 69928
For technical questions, please call 1-800-444-3353. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SAFETY
PLEASE READ THE...
User Manual - Page 18
...
27 Bumper B
28 Body
29 O-ring 62.3×1.8
30 Nose
Part
Description
31 Spring Washer
32 Screw
33 Spring
34 Safety Bracket A
... Clip
41 Spring Pin
42 Safe Guide
43 O-ring 18.4x2.4
44 O-ring 20.3x1.5
45 Valve Set
46 O-ring 9.5x1.9
47 O-...Support
73 Nut
74 Lock
75 Torsion Spring
76 Bushing
77 Nut
78 Nut
79 Soft Grip Sleeve
80 Gasket
81 End Cap
82 Screw
83 Air Plug
SETUP...
User Manual - Page 19
...27 Bumper B
28 Body
29 O-ring 62.3×1.8
30 Nose
Part
Description
31 Spring Washer Ø8
32 Screw M8×25
33...Clip
41 Spring Pin
42 Safe Guide
43 O-ring 18.4x2.4
44 O-ring 20.3x1.5
45 Valve Set
46 O-ring 9.5x1.9
47...Support
74 Nut M5
75 Lock
76 Torsion Spring
77 Bushing
78 Nut M4
79 Nut M6
80 Soft Grip Sleeve
81 Gasket
82 End Cap
83 Screw M5×20
84 Air Plug
SETUP...
Harbor Freight Tools 69927 Reviews
We have not received any reviews for Harbor Freight Tools yet.