Harbor Freight Tools 62862 - 6 in. 5.7 Amp Heavy Duty Dual Action Variable Speed Polisher Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 62862 manuals!
Problems with Harbor Freight Tools 62862?
Ask a Question
Free Harbor Freight Tools 62862 manuals!
Problems with Harbor Freight Tools 62862?
Ask a Question
Popular Harbor Freight Tools 62862 Manual Pages
User Manual - Page 1
...com Email our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged. No portion of this manual or any artwork contained... procedures. Read this material before using this manual for assembly and service may not be drawn proportionally. Owner's Manual & Safety Instructions
Save This Manual Keep this product. If any shape or ...
User Manual - Page 2
...instructions. The term ″power tool″ in the presence of Contents
Safety 2 Specifications 9 Setup 9 Operation 10
Maintenance 12 Parts List and Diagram 14 Warranty 16
Safety
Setup
... injury. IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all warnings and instructions for future reference. Keep children and bystanders away while operating a power tool....
User Manual - Page 3
Safety
Setup
Electrical safety
1. Personal safety
1. Do not use common sense when operating a power tool. ...tools to a rotating part of electric shock.
6. Only use reduces the risk of the power tool may not provide adequate protection. Water entering a power tool will reduce risk of electric shock.
4. Use of a cord suitable for the specific hazards in the off-...
User Manual - Page 4
... and are caused by a qualified repair person using only identical replacement parts. Properly maintained cutting tools with these instructions to be performed with the switch is maintained. Do not use and care
1. If power tool or accessory is intended to follow all safety warnings, instructions, illustrations and specifications provided with arbor holes that...
User Manual - Page 5
..., contact Harbor Freight Tools for a replacement.
18. Turn off the tool, ...of work. Page 5 Safety
Setup
be capable of filtering out ...must be pulled into this instruction manual cannot cover all possible conditions...support the workpiece to cause cancer, and birth defects or other reproductive harm. (California Health & Safety Code... may make exposed metal parts of control and personal ...
User Manual - Page 6
...Setup
Kickback and Related Warnings
Kickback is a choice between different processes.
5. Safety Warnings Specific...manual.
Wear suitable gloves to the hands, arms and shoulders. Always use . Follow manufacturer's recommendations when selecting sanding paper. Operation
Maintenance
Page 6
SAVE THESE INSTRUCTIONS...body and arm to ensure medical problems are taken.
2. Kickback will...
User Manual - Page 7
...Setup
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is connected through the green wire inside the cord to the grounding system in the tool. Tools marked with all codes...a proper outlet installed by a service facility before use...outlet, have it repaired by a qualified ...
User Manual - Page 8
... indicate it repaired by a qualified electrician before set-up the ...total length, make sure it .
8. Make sure the extension cord is marked with the suffix "W-A" ("W" in Canada) to determine the required minimum cord size. (See Table A.)
6. Always replace...Table A.)
5. Safety
Setup
Extension Cords
1. Using...Inc.
Item 62862 Read the manual before using more than a ...
User Manual - Page 9
... additional information regarding the parts listed in one hand only or without the Side Handle properly installed.
1. The Side Handle may be installed in the following pages, refer to the Assembly Diagram near the end of the Gear Housing.
2. Tighten securely before performing any procedure in this manual.
Page 9 Safety
Setup
Specifications
Electrical Rating No Load...
User Manual - Page 10
...a hazard while working .
3. Setup
Operation
Maintenance
Page 10
For technical...the beginning of this manual including all text under subheadings therein before set up or use ... Item 62862
Workpiece and Work Area Set Up
1. Safety
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section...the Spindle.
4. Installing a Threaded Accessory
1. Tool Set Up
TO PREVENT...
User Manual - Page 11
... to the vehicle's finish due to a complete stop before setting it down. To start, position the unit on the clean...the Switch is applying too much wax. Note: The most common error when waxing/polishing a vehicle is in the offposition, then plug... knots. Tightly pull the string to the vehicle.
Polishing Instructions
Safety
Setup
TO PREVENT SERIOUS INJURY: Grip the tool firmly in both...
User Manual - Page 12
... and down . Wait until the tool has reached full speed, then gently contact the surface.
6. Maintenance and Servicing
Procedures not specifically explained in both hands and press the Trigger. Cleaning, Maintenance, and Lubrication
1. Keep heavy pressure off the tool. Safety
Setup
Sanding Instructions
TO PREVENT SERIOUS INJURY: Grip the tool firmly in this section.
User Manual - Page 13
...replacement parts.
Check that cord is needed , use one with the proper diameter for its length and load. If breaker is tripped, make sure circuit is tight. 2. If an extension cord is plugged in GROUNDING section. Setup... Some parts are listed and shown for example.)
Overheating.
1. Have technician service tool.
1.
Safety
Troubleshooting
Problem
Tool ...
User Manual - Page 14
...PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 62862 Parts List
Part... Fan Guide Bearing 607 Bushing
Q'ty
1 3 2 6 1 1 3 1 1 1 4 7 1 1 4 1 1 1 1 2 1 1 1 1
Part
25 26...
User Manual - Page 15
Page 15
Safety
Setup
Assembly Diagram
18 17
45
46
16
19
15
47
20
14
3
21
13
22
23
12
24
11
25
4 2
30 31
26 27
10
32 33
28
9
34
29
8
7
6
5 4
35
3
36
2
37
2
38
1
41 42 43 44
39
40
Operation
Maintenance
Item 62862
For technical questions, please call 1-888-866-5797.
Harbor Freight Tools 62862 Reviews
We have not received any reviews for Harbor Freight Tools yet.