Gigabyte GA-8I925XE-G Support and Manuals
Get Help and Manuals for this Gigabyte item
View All Support Options Below
Free Gigabyte GA-8I925XE-G manuals!
Problems with Gigabyte GA-8I925XE-G?
Ask a Question
Free Gigabyte GA-8I925XE-G manuals!
Problems with Gigabyte GA-8I925XE-G?
Ask a Question
Popular Gigabyte GA-8I925XE-G Manual Pages
Manual - Page 2
...and boot sequence in BIOS Setup.
(3)* Configure RAID set up IDE RAID hard drive(s), follow the steps below
¤å
(1) Install IDE hard drive(s) in ...model and capacity). "*" Skip this step if you do not want to the IDE port that you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard.
(1) Installing...
Manual - Page 4
...select the desired IDE hard drive onto which you can boot from Installation CD after system restarts.(Figure
3)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features
: Move...¤å
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Hard Disk Boot Priority
Step 3
Figure 2
Set First Boot Device to CD-ROM so you want to install
¤¤
Microsoft ...
Manual - Page 14
... RAID Drives Configuration (GigaRAID) - 14 - Figure 16 Step 3: Go to copy the driver. The installation utility will appear automatically. Quit the installation utility first.
The instructions below explain how to the BootDrv folder and look for the IDE RAID controller from the motherboard driver CD to
a floppydisk.
Step 2: Go to My Computer and right-click the...
Manual - Page 12
... 0 (stripe) array. GigaRAID (IT8212) ATA RAID Controller USER'S MANUAL
Totally, there are sent to set as array 0. Selecting RAID 0 can increase data transfer rate and allow the best overall performance characteristics because of disks needed 2 or 3 or 4 2 4 2 or 3 or 4 1 or 2 or 3 or 4
Setup Array for RAID 0: The GigaRAID (IT8212) ATA RAID Controller allows...
Manual - Page 38
..., WinXP, Win2000 ), for that hard drive. Follow on-screen instructions to complete installation. (Each time you complete the steps, boot from the Windows CD to install the RAID drivers.
Please follow the steps below to complete driver transfer to a floppy disk: 1) Please insert the provided driver CD into the floppy disk drive. 3) Either from HDDs in...
Manual - Page 52
User should remove the device and reinstall.
52 under SCSI and ATA RAID Controller device, it
indicates that the driver has not been correctly installed. GigaRAID (IT8212) ATA RAID Controller USER'S MANUAL 3. or ? If there is a marking !
Manual - Page 1
Table of Contents
Configuring SATA Hard Drive(s) (Controller Intel ICH6R 2 (1) Installing SATA hard drive(s) in your computer 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup 3 (3) Configuring RAID set in RAID BIOS 5 (4) Making a SATA Driver Disk ...9 (5) Installing SATA controller driver during OS installation 11
Manual - Page 9
... motherboard driver CD into the CD-ROM drive. Without the driver, the hard drives
¤¤
may not be recognized during OS installation.
Step 2: Go to a
floppy disk.
The instructions below...install required driver for the SATA controller during the Windows setup process.
¤å
First of all, you need to copy the driver for the SATA controller from the motherboard driver ...
Manual - Page 11
... to that you have prepared the SATA driver disk and configured BIOS settings, you are ready to install Windows 2000/XP onto your system to boot from the Windows 2000/XP Setup disk and press F6 as soon as
you need to install a 3rd party SCSI or RAID driver" message (Figure 15).
Figure 16 SATA Hard...
Manual - Page 21
.../ IDE2 / IDE3 (IDE Connector) An IDE device connects to the instructions located on settings, please refer to the computer via an IDE connector. The types of...). If you wish to connect two IDE devices, please set the jumper on one IDE cable, and the single IDE...39
IDE
2 2 IDE2
IDE3 1
- 21 -
1 40
39
Hardware Installation One IDE connector can then connect to the FDD drive. English
7) FDD ...
Manual - Page 22
...
11) PWR_LED PWR_LED is connect with the system power indicator to work properly. Definition
1
1
MPD+
2
MPD-
3
MPD-
GA-8I925XE-G / GA-8I925XC-G Motherboard - 22 - Pin No.
Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to indicate whether the system is on/off. It will blink when the system enters...
Manual - Page 32
...Setup. You can manually input the correct settings.
is , , , . IDE Channel 0 Master, Slave IDE HDD Auto-Detection Press "Enter" to automatically detect IDE devices during POST(default)
• None
Select this to Sat.
GA-8I925XE-G / GA-8I925XC-G Motherboard - 32 - to set... up.
• Manual User can use one of sectors
If a hard disk has not been installed, select NONE and press...
Manual - Page 46
... you are prompted to confirm the password being disabled. A message "PASSWORD DISABLED" will appear to enter password. GA-8I925XE-G / GA-8I925XC-G Motherboard - 46 - You may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic...
Manual - Page 64
... reboots.
GA-8I925XE-G / GA-8I925XC-G Motherboard - 64 - When you exit the BIOS menu. This part guides users of single-BIOS motherboards how to load BIOS Fail-Safe Defaults. Press Del to load defaults.
7. Press Y on your keyboard to save the settings to CMOS and EXIT (SYe/tNS)u?pYervisor Password
PnP/PCI Configurations
Set User Password
PC Health Status
Save & Exit Setup
MB...
Manual - Page 75
... in MS-DOS mode(Note 1). Use an alternative system and insert the GIGABYTE motherboard drive CD-ROM. Appendix First of all, copy the driver for that has CD-ROM support and a blank formatted floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in the BootDrv folder. At the D:\> prompt, type the following...
Gigabyte GA-8I925XE-G Reviews
We have not received any reviews for Gigabyte yet.