Garmin Vector 3 Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Vector 3 manuals!
Problems with Garmin Vector 3?
Ask a Question
Free Garmin Vector 3 manuals!
Problems with Garmin Vector 3?
Ask a Question
Garmin Vector 3 Videos
Garmin Vector 3 and 3S - Pedal-Based Power Meter
Duration: 4:06
Total Views: 22,803
Duration: 4:06
Total Views: 22,803
Hands-on: Garmin Vector 3 Bluetooth Firmware Finally Out!
Duration: 6:18
Total Views: 30,878
Duration: 6:18
Total Views: 30,878
Garmin Vector 3 Unboxing!
Duration: 10:42
Total Views: 54,558
Duration: 10:42
Total Views: 54,558
Garmin VECTOR 3 Power Meter: Alternative Battery Install (CR1/3N)
Duration: 5:48
Total Views: 47,155
Duration: 5:48
Total Views: 47,155
Popular Garmin Vector 3 Manual Pages
Owners Manual - Page 1
VECTOR™ 3 AND VECTOR 3S
Owner's Manual
Owners Manual - Page 2
... Peaksware, LLC. Other trademarks and trade names are trademarks of their respective owners. The FCC ID is located in part, without the express permission of Garmin. Garmin Connect™ and Vector™ are those of Garmin Ltd. Mac® is under license. or its subsidiaries
All rights reserved.
Go to change or improve its subsidiaries...
Owners Manual - Page 3
... 4 Vector Specifications 4 Battery Information 4 Overhauling the Vector Pedals 4 Vector Storage 6
Other Compatible Devices 6 Edge 1000 Instructions 6 Edge 520 and Edge 820 Instructions 6 Forerunner® 935 and fēnix® 5 Series Instructions 6
Appendix 6 Registering Your Vector System 6 Upgrading Your Vector 3S to a Dual Sensing System 6 Power Data Fields 7 Troubleshooting...
Owners Manual - Page 5
... the Important Safety and Product Information guide in the left pedal.
Error codes are the same. 1 Apply a thin layer of 25 lbf-ft. (34 N-m). 6 Repeat steps 2 through 5 to put the power under your bike.
This manual covers both Vector systems. Vector was successful. Now it's time to install the left pedal only.
The Vector 3S system installation is in serious injury.
The...
Owners Manual - Page 6
...Dual Sensing System, page 6. This procedure contains instructions for the Edge 1030. NOTE: The Vector 3S system does not support cycling dynamics.
Use a 3 mm hex key to activate Vector. 2 Select > Sensors. 3 Select your device, is a window on the pedal, allowing you have another compatible device, see your owner's manual. 1 Rotate the pedals a few hundred times every second. If...
Owners Manual - Page 7
... is the pedal stroke region (between the start crank angle and the end crank angle) where you must safely disconnect your computer.
Sending Your Ride to your Garmin Connect account on your ride data. The device does not automatically delete or overwrite your activities: You can update Vector software and settings using the Garmin Connect app...
Owners Manual - Page 8
... socket wrench with an outer diameter that is no battery carriage. 1 Use a 15 mm pedal wrench to www.garmin.com/manuals/vector3 for product warnings and other important information.
of riding time, with Garmin parts only. When you receive a low battery warning, you have approximately 10-20 hours of the batteries at the same time. The cover is sufficiently...
Owners Manual - Page 9
... and two screws. 18Replace the batteries and battery cover, and hand tighten it to the recommended torque specification. 3 Set the battery cover and batteries aside.
4 Use a small Phillips screwdriver (PH 00) to remove the two screws from inside the battery carriage . 5 Remove the battery carriage. 6 While securely holding the wrench flats with a pedal wrench, use the 12 mm socket...
Owners Manual - Page 10
... Crank Length. Upgrading Your Vector 3S to a Dual Sensing System
Before you install the new right pedal, the left pedal must be paired and connected to a compatible Edge device or the Garmin Connect app. 1 Review the Vector installation instructions (Installing the
Vector Components, page 1). 2 Remove the existing right pedal. 3 Install the new right pedal (Installing the Pedals, page 1). 4 Rotate...
Owners Manual - Page 11
... output. R. Trainer Resistance: The resistance force applied by the Vector S system. Power Data Fields
NOTE: This list contains power data fields for the current lap. Power - Lap: The average power phase angle for the left /
right power balance. Power phase is the pedal stroke region where positive power is produced. Power Phase - Power...
Owners Manual - Page 12
... instructions. Performing a Static Torque Test NOTICE
The static torque test is intended for software updates and sends them to your Edge device. 2 Bring your product name. 3 Enter "torque test" to view the FAQ topic. Garmin Connect automatically looks for advanced cyclists and installation experts. The left pedal receives the software update. Troubleshooting
Updating the Vector...
Owners Manual - Page 13
...computer 3
I installing 1
M maintenance 4 memory 3
P pairing 1, 2, 6
smartphone 3 pedals 1, 2, 4 platform center offset 3 power 2 power (force), meters 2 power phase 3 product registration 6
R registering the device 6 resetting the device 8
S settings 3 smartphone, pairing 3 specifications 4 storing data 3 storing the device 6
T tools 1 training 4 troubleshooting 8
U upgrading 6 USB, disconnecting...
Important Safety and Product Information - Page 2
... goods repaired or replaced if the goods fail to be found to comply with comparable Garmin products and parts, or require you to ship your product to a Garmin Authorized service facility in the country of original purchase or to a Garmin Authorized service facility in another country that all instructions carefully before installing the components and riding. • Understand how the pedal...
Garmin Vector 3 Reviews
We have not received any reviews for Garmin yet.