Garmin Panoptix PS60 Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Panoptix PS60 manuals!
Problems with Garmin Panoptix PS60?
Ask a Question
Free Garmin Panoptix PS60 manuals!
Problems with Garmin Panoptix PS60?
Ask a Question
Popular Garmin Panoptix PS60 Manual Pages
Installation Instructions - Page 1
... your boat. It does not relieve you of the responsibility of the water beneath your vessel. Panoptix™ PS60
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder product box for the software update instructions to appear, the device must be fully booted before proceeding with the...
Installation Instructions - Page 2
...deadrise angle of the specific point on the table so the cutting guide rests against the fence...settings to display a flipped image. Failure to do so could result in .) from
the
top
edge
, À
and 61 mm (2.4 in the device rotating while the boat is moving and could cause damage to your boat manufacturer for increased sonar accuracy. Cored Fiberglass Boat Hull Installation Instructions...
Installation Instructions - Page 3
... and in a Fiberglass Hull It is recommended that two installers complete these instructions, with EMC standards. The fairing block and transducer must...install all three included ferrite beads around both the power and Garmin Marine Network cables, as close to the transducer stem as possible.
3
NOTE: When installing...set thoroughly. 8 While holding a drill with epoxy , and allow the epoxy to...
Installation Instructions - Page 4
... half of the fairing block that two installers complete these instructions, with the screws .
3 Secure the...Garmin Marine Network cables, as close to the exposed transducer stem and anti-rotation bolts. 10Pull the transducer cable, transducer stem, and anti-rotation bolts through the bottom half of national EMC standards and other laws. Non-cored Fiberglass Boat Hull Installation Instructions...
Installation Instructions - Page 5
... transducer, and hull. The fairing block and transducer must install all excess sealant on a boat that two installers complete these instructions when you must apply marine sealant to the water path ... in.) pilot hole through the hull from outside of the three ferrite beads around both the power and Garmin Marine Network cables, as close to the water surface. 4 Using a 38 mm (11/2 in .)...
Installation Instructions - Page 6
...or putty knife to work properly. or its subsidiaries
www.garmin.com/support Panoptix™ is necessary to carry the sonar signal, the transducer must be used without the express permission of... You cannot get a depth or distance reading when out of the water. Maintenance
Testing the Installation
NOTICE You should apply a water-based anti-fouling paint to your vessel, because ketones attack ...
Thru-Hull Template - Page 1
... than the template. Notice
Garmin is not responsible for any damages or expenses resulting from a miscut mounting surface arising from a failure to follow these instructions for Page Scaling ➊...larger than the template ➍.
If you do print the template, you must follow these instructions, may result in an incorrectly sized template and therefore an incorrect cutout (too large or ...
Thru-Hull Template - Page 2
Panoptix™ PS60 Template
14 mm (3/16 in.)
19 mm (3/4 in.)
38 mm (1 1/2 in.)
32 mm (1 1/4 in.)
14 mm (3/16 in.)
19 mm (3/4 in.)
August 2015
140 mm (5 1/2 in.)
140 mm (5 1/2 in.)
190-01900-04_0A
Printed in Taiwan
?Declaration of Conformity - Page 1
... equipment and systems - Marine Sonar Transducer
Panoptix PS60
The undersigned does hereby declare that the equipment complies with the above Directives
Jamie Wiltshire Quality Supervisor Garmin (Europe) Ltd. Issued: 16/10/2015 Revised: 19/4/2016 Page: 1 of 1
DECLARATION of CONFORMITY
Application of Equipment: Model Number(s):
GARMIN International & 1200 E. 151st Street Olathe, Kansas...
Garmin Panoptix PS60 Reviews
We have not received any reviews for Garmin yet.