Garmin LiveScope LVS32-IF Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin LiveScope LVS32-IF manuals!
Problems with Garmin LiveScope LVS32-IF?
Ask a Question
Free Garmin LiveScope LVS32-IF manuals!
Problems with Garmin LiveScope LVS32-IF?
Ask a Question
Garmin LiveScope LVS32-IF Videos
Rytek Marine: Garmin Livescope LVS32 Trolling Motor/Pole Multi-view transducer mount.
Duration: 19:23
Total Views: 1,711
Duration: 19:23
Total Views: 1,711
Garmin Livescope LVS32 vs LVS12 what do you need.
Duration: 1:25
Total Views: 2,944
Duration: 1:25
Total Views: 2,944
2021 Garmin Livescope LVS32 Unboxing
Duration: 18:18
Total Views: 252
Duration: 18:18
Total Views: 252
Garmin Livescope LVS32 Offshore Application # 2
Duration: 1:45
Total Views: 5,334
Duration: 1:45
Total Views: 5,334
Popular Garmin LiveScope LVS32-IF Manual Pages
Installation Instructions - Page 1
... the installation, go to support.garmin.com for more information.
Software Update
You must install the Garmin® device according to your chartplotter owner's manual at support.garmin.com. You are responsible for product warnings and other important information. Read all installation instructions before proceeding with these instructions. If you navigate.
Sonar is on updating the...
Installation Instructions - Page 2
... will not be submerged. You should create a service loop at least 25 cm (10 in.) long in a location where it will not be exposed to the center line of the boat . You should mount the transducer as close to
extreme temperatures. • You should mount the transducer in the cable, with the rotating joint centered...
Installation Instructions - Page 3
... motor to tension during rotation. Installing the Transducer on a Trolling Motor
Assembling the Trolling Motor Barrel Mount Hardware
1 Align the top of the transducer with the top of the bracket .
2 Using the included hex wrench, attach the bracket to the transducer. Routing the Transducer Cable
You should test-fit the transducer and cable before installation. 1 Allow a loose gap of...
Installation Instructions - Page 4
...garmin.com or from your Garmin dealer. 5 Position the transducer to the transducer cable wires or cable jacket can cause transducer failure. 1 Insert the hose clamp through the slot on the trolling motor mount... Mount Orientation, page 5).
4 NOTE: Do not rotate the transducer.
3 Secure the transducer cable to the motor shaft or other secure location. 4 Route the transducer cable to the installation...
Installation Instructions - Page 5
... Port side, forward view Port side, downward view
Installing the Transducer on , and your desired field of view. You must orient the arrow and the narrow end of the angle to the top when you have mounted the transducer on a Trolling Motor Shaft
Trolling Motor Shaft Bracket Orientation
The trolling motor shaft bracket features an 8-degree...
Installation Instructions - Page 6
... trolling motor is 2.5 lb-ft. (3.4 N-m). Assembling the Trolling Motor Shaft Mount Hardware
With the trolling motor bracket oriented correctly (Trolling Motor Shaft Bracket Orientation, page 5), use the included rubber insert on the Trolling Motor Shaft
NOTICE You must fully tighten the mount to the transducer. The recommended torque applied to the shoulder screw is deployed or...
Installation Instructions - Page 7
... necessary, to the transom mount bracket using the mounting screws
and lock
2 Attach the transducer mount bracket to reduce spray from forward to buy.garmin.com or contact your desired field of the trolling motor shaft you can install an optional spray shield (010-12406-00).
Trolling Motor Shaft Orientation
The angle of installation depends on the side of...
Installation Instructions - Page 8
... 20 mm screws , attach the transducer mount to electrical wires or other sources of the gel coat. 5 Using the 4 mm (5/32 in.) bit, drill the pilot holes approximately 19 mm (3/4 in step 9. • If you are installing the bracket on vessels that operate at high speeds. NOTICE When mounting the transducer, be sure to 12.7 mm...
Installation Instructions - Page 9
...be suitable for one corner of the pilot holes. 2 Drill a pilot hole for the mounting surface. This will help to avoid cracking in the gel-coat layer when the screws are...in fiberglass, when drilling the pilot holes, use a countersink bit to the mounting location.
9 Mounting the GLS 10 Black Box Device
NOTICE If you must select a mounting location, and determine what screws and other ...
Installation Instructions - Page 10
...Panoptix LiveScope GLS 10 sonar module Garmin Marine Network adapter cable (Garmin part number 010-12531-01) Garmin Marine Network cable, small connector to malfunction and will void the warranty. Panoptix LiveScope GLS 10 power cable to POWER port Transducer cable to XDCR port Panoptix LiveScope LVS32 transducer
1 For chartplotter connections, refer to your chartplotter installation instructions...
Installation Instructions - Page 11
Power Cable Extensions
If necessary, you can extend the power cable using the appropriate wire gauge for the length of the extension. Item
Description Fuse Battery 9 ft. (2.7 m) no extension
Item
Description Splice • 10 AWG (5.26 mm&#...
Installation Instructions - Page 12
... you must be installed on -screen instructions.
12 You can calibrate the compass, the transducer must fully rotate your chartplotter owner's manual. Red
Three blinks followed by a The transducer is turned on the chartplotter. Transducer Settings and Operation
For transducer settings and operation information, see sonar data on . Orange Blinking
A software update is pointing...
Installation Instructions - Page 13
... to 85°C (from -40 to 185°F)
Power input
From 10 to developer.garmin.com/open -source software license(s) used without the express permission of Garmin. Specifications
Panoptix LiveScope LVS32 Specifications
Dimensions (L x H x W) Weight (transducer only) Frequencies Operating temperature Storage temperature Maximum depth/distance1
Field of their respective owners.
1 Dependent...
Garmin LiveScope LVS32-IF Reviews
We have not received any reviews for Garmin yet.