Manual/User Guide
Page 1
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E262 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E262 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover ... M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached.
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover ... M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached.
Manual/User Guide
Page 6
... circulation in the cabinet such that the PCA side, in Table 3.1. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and...
... circulation in the cabinet such that the PCA side, in Table 3.1. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and...
Manual/User Guide
Page 7
.... (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Damage: Do not press the cover of the disk drive. Pressing it by external magnetic fields. Static: When handling the device, disconnect the body ground (500 kΩ or greater). 3.2 Mounting (5)...connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the...
.... (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Damage: Do not press the cover of the disk drive. Pressing it by external magnetic fields. Static: When handling the device, disconnect the body ground (500 kΩ or greater). 3.2 Mounting (5)...connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the...
Manual/User Guide
Page 9
Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
Manual/User Guide
Page 10
..., refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification. 3-10 C141-E262
..., refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification. 3-10 C141-E262
Manual/User Guide
Page 11
Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and ...connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10 kgf of...
Accordingly, be compliant with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be sure to connector damage and the loss of force in the connection direction once they are snugly and ...connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10 kgf of...