Manual/User Guide
Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E254 3-1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E254 3-1
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E254 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E254 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
... Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The mounting frame is connected...
... Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The mounting frame is connected...
Manual/User Guide
Page 4
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E254 if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values;
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E254 if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values;
Manual/User Guide
Page 5
Locating of breather C141-E254 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block.
Locating of breather C141-E254 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 6
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Measurement point Temperature 1 DE cover 60 °C max 3-6 C141-E254 Provide air circulation in the cabinet such that the PCA side, in Table 3.1. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must...
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. Measurement point Temperature 1 DE cover 60 °C max 3-6 C141-E254 Provide air circulation in the cabinet such that the PCA side, in Table 3.1. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must...
Manual/User Guide
Page 7
... circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Mounting screw hole Cable connection Figure 3.5 Service area Mounting screw hole Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation.
... circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Mounting screw hole Cable connection Figure 3.5 Service area Mounting screw hole Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation.
Manual/User Guide
Page 8
... of the driver. (2) Please observe the tightening torque of a low impact when you use the driver of the screw strictly. Do not hit HDD each other. Figure 3.6 Handling cautions - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-...3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E254 ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Installation (1) Please use an electric driver. General notes Wrist strap Use...
... of the driver. (2) Please observe the tightening torque of a low impact when you use the driver of the screw strictly. Do not hit HDD each other. Figure 3.6 Handling cautions - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-...3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E254 ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Installation (1) Please use an electric driver. General notes Wrist strap Use...
Manual/User Guide
Page 9
Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E254 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E254 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices.
Manual/User Guide
Page 10
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system Table 3.2 lists the recommended specifications for the host interface connectors. The connection reliability per number of insertion/extractions varies with the condition of the SATA interface connector and pin numbers. Power supply segment Signal segment View from the connector side P1 pins in the power supply segment S1 pins in the signal segment View from the several choices including its mating with the SATA interface connecter...
... 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system Table 3.2 lists the recommended specifications for the host interface connectors. The connection reliability per number of insertion/extractions varies with the condition of the SATA interface connector and pin numbers. Power supply segment Signal segment View from the connector side P1 pins in the power supply segment S1 pins in the signal segment View from the several choices including its mating with the SATA interface connecter...
Manual/User Guide
Page 11
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10...
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10...