Fujitsu MAM3367MC - 36GB SCSI Hard Drive SCA2 Ultra160 80 PIN 15K RPM Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAM3367MC manuals!
Problems with Fujitsu MAM3367MC?
Ask a Question
Free Fujitsu MAM3367MC manuals!
Problems with Fujitsu MAM3367MC?
Ask a Question
Popular Fujitsu MAM3367MC Manual Pages
Product Manual - Page 14
...A.2 Locations of Connectors and Setting Terminals (MP model A-3
APPENDIX B SETTING TERMINALS B-1 B.1 Setting Terminals (MP model)...B-2
APPENDIX C CONNECTOR SIGNAL ALLOCATION C-1 C.1 SCSI Connector Signal Allocation: SCA2 type LVD 16-bit SCSI C-2 C.2 SCSI Connector Signal Allocation: 68 pin type LVD 16-bit SCSI C-3
APPENDIX D MODEL NAMES AND PRODUCT NUMBERS D-1 D.1 Model Names and Product...
Product Manual - Page 16
...example 4-22 SCSI bus connections (1 of 2 5-4 SCSI bus connections (2 of 2 5-4 IDD setting terminals position (MP model only 5-5 Setting terminator (CN2 on MP model only 5-6 Checking the SCSI connection (A 5-14 Checking the SCSI connection (B 5-15 Revision label...6-9 Indicating revision numbers 6-10 Test flowchart ...6-11 Format of extended sense data 7-2 Circuit configuration ...8-4 IDD...
Product Manual - Page 17
... DEFINITION command 5-9 Setting check list (MP model only 5-10 Self-diagnostic functions...6-1 System-level field troubleshooting 6-14 Disk drive troubleshooting 6-15 Definition of sense data...7-3 Setting terminal: CN2 (MP model B-2 SCSI connector (SCA2 type LVD 16-bit SCSI): CN1 C-2 SCSI connector (68 pin type LVD 16-bit SCSI): CN1 C-3 MAN series model names and product numbers D-2
C141...
Product Manual - Page 34
... power so that requires repair, adjustments, or replacement. Mishandling by the operator, failures due to diagnose and repair a drive malfunction. Failure of the equipment means failure that DE surface temperature is 5 years. The service life is the average time taken by a well-trained service mechanic to bad environmental conditions, power trouble, host system trouble, cable failures, or...
Product Manual - Page 59
[Surface P'] • Setting terminal(MP model only) • External operator panel connector
[Surface P] • Cable
connection
[Surface R] • Hole for mounting screw
[Surface Q] • Hole for mounting screw Figure 4.7 Service clearance area
(6) External magnetic field
The drive should not be installed near equipment.
(8) Others Seals on the DE prevent the DE inside from the dust....
Product Manual - Page 63
... conforming to Sections 1.3 and 1.4 in the SCSI Physical Interface Specifications.
C141-E134-01EN
4 - 11 4.3 Connection Requirements 4.3.1 68 pin connector 16-bit SCSI model (MP model) (1) Connectors
Figures 4.13 show the locations of connectors and terminals on the 68 pin connector type 16-bit SCSI (MP) model. • Power supply connector • SCSI connector • External...
Product Manual - Page 75
...operations after installation and preparation for setting. CHAPTER 5 INSTALLATION
5.1 Notes on Handling Drives 5.2 Connections 5.3 Setting Terminals 5.4 Mounting Drives 5.5 Connecting Cables 5.6 Confirming Operations after Installation and Preparation
for Use 5.7 Dismounting Drives 5.8 Spare Disk Drive
This chapter describes the notes on Handling Drives The items listed in the specifications in...
Product Manual - Page 90
... blocks, specify the number in the "number of cylinders in the format parameter (page code = 3) and drive parameter (page code = 4).
5 - 16
C141-E134-01EN The user can be formatted (initialized) when it is installed in the "data block length" field. The parameters are connected correctly. • The terminating resistor is mounted on the setting of the logical data...
Product Manual - Page 94
... data specified with a command
Refer to use the default setting in an operation status under the average system load requirements....normal operations.
(2) Disconnection/reconnection parameters (page code = 2)
The following parameters are used to ...EXTENDED, or WRITE AND VERIFY command) of SCSI Logical Interface Specifications for how to obtain the rough calculation values for further details...
Product Manual - Page 103
... error analysis information
CAUTION
Data loss Save data stored on the disk drive before requesting repair. Fujitsu does not assume responsibility if data is destroyed during servicing or repair. (3) Parts that can be replaced in the field
The PCA cannot be replaced in the field.
(4) Service system and repairs
Fujitsu has the service system and repair facility for replacing or repairing the...
Product Manual - Page 131
APPENDIX A LOCATIONS OF CONNECTORS AND SETTING TERMINALS
A.1 Locations of Connector (MC model)
A.2 Locations of Connectors and Setting Terminals (MP model)
This appendix shows the locations of connectors and setting terminals.
C141-E134-01EN
A - 1
Product Manual - Page 133
A.2 Locations of Connectors and Setting Terminals (MP model) CN2
CN1 (Bottom view)
Pin 34
Pin1 Pin A11 Pin A1
Pin 1
Pin 68
Pin 35 Pin A12
Pin A2
Power connector (CN1)
SCSI connector (CN1)
Connector for external operator panel (CN1)
(Rear view)
Figure A.2
Locations of connectors and setting terminals (MP model)
C141-E134-01EN
A - 3
Product Manual - Page 135
APPENDIX B SETTING TERMINALS
B.1 Setting Terminals (MP model) This appendix describes setting terminals. C141-E134-01EN
B - 1
Product Manual - Page 136
B - 2
C141-E134-01EN B.1 Setting Terminals (MP model)
Table B.1 Setting terminal: CN2 (MP model)
Setting item SCSI ID
Write protect
Pins 9 - 10 7 - 8 5 - 6
(Open) Open (Open) Open (Open) Open (Open) Open (Open) Short (Open) Short (Open) Short (Open) Short Short Open ...
Product Manual - Page 143
...3D-00 7-4 5-90-00 7-4 68-pin connector 16-bit SCSI model 4-11 68-pin type LVD C-3 8-bit SCSI/16-bit SCSI 1-2
A
AC noise filter 4-10... 5-21 CHANGE DEFINITION command 5-9 changing revision number in field 6-9 check before mounting 5-10...installation and
preparation for use 5-12 connecting cable 5-11 connection 5-3 connection requirement 4-11 connector 4-11, 4-19 connector and terminal location
(MP model...
Fujitsu MAM3367MC Reviews
We have not received any reviews for Fujitsu yet.