Installation Instructions
Page 1
... bottom legs) 2 3 Plastic Divider ( 1 8" x 4 1 2" x 141 2" ) 2 12 Ground Wire (green) 1 4 Stuffer Seal (1" x 1 1 2 " x 84" ) 1 13 Toothed washer for existing sleeve) Note that may not need all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Installation Instructions READ BEFORE INSTALLING UNIT... For Through-the-Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Observe all...
... bottom legs) 2 3 Plastic Divider ( 1 8" x 4 1 2" x 141 2" ) 2 12 Ground Wire (green) 1 4 Stuffer Seal (1" x 1 1 2 " x 84" ) 1 13 Toothed washer for existing sleeve) Note that may not need all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Installation Instructions READ BEFORE INSTALLING UNIT... For Through-the-Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Observe all...
Installation Instructions
Page 2
..., drill a 3/16" clearance hole for grounding screw through sleeve, into wall, if needed . 3. Pull loose end of ground wire out front of sleeve, using grounding screw and toothed washer. Retouch wall sleeve painted surface if needed . Hole Fig.1 2 LEVEL Fig.2 Brand Width Wall Sleeve Dimensions Height White-Westinghouse Frigidaire Carrier (52F Series) General Electric/Hotpoint Whirlpool Fedders/Emerson...
..., drill a 3/16" clearance hole for grounding screw through sleeve, into wall, if needed . 3. Pull loose end of ground wire out front of sleeve, using grounding screw and toothed washer. Retouch wall sleeve painted surface if needed . Hole Fig.1 2 LEVEL Fig.2 Brand Width Wall Sleeve Dimensions Height White-Westinghouse Frigidaire Carrier (52F Series) General Electric/Hotpoint Whirlpool Fedders/Emerson...
Installation Instructions
Page 3
...result from having two rear air intakes. If there is an existing sleeve, and there is installed. Prepare the wall sleeve for that has been shipped with the unit in the accessory kit.... Remove the existing grille. 2. Installation Instructions 4. Most decorative exterior grilles may lead to be left in the following Brand instructions. #1 Emerson #2 Fedders #3 Fedders or Friedrich #4 General Electric/Hotpoint #5 Sears or Carrier(51S Series) #6 Whirlpool #7 Whirlpool #8 White-Westinghouse/Frigidaire...
...result from having two rear air intakes. If there is an existing sleeve, and there is installed. Prepare the wall sleeve for that has been shipped with the unit in the accessory kit.... Remove the existing grille. 2. Installation Instructions 4. Most decorative exterior grilles may lead to be left in the following Brand instructions. #1 Emerson #2 Fedders #3 Fedders or Friedrich #4 General Electric/Hotpoint #5 Sears or Carrier(51S Series) #6 Whirlpool #7 Whirlpool #8 White-Westinghouse/Frigidaire...
Installation Instructions
Page 4
...View 2. Attach(1)1" x 3/8" x 25" long seal in center of side wall with mounting the grill to the left side of the ground wire from sleeve to 14" long each side wall. Remove the backing paper and press into sleeve. 7. Make sure that the toothed washer is against the cabinet. 10....the other end of unit. 8. Seal & Frame the unit as shown in flange of this manual and replace with provided louvered rear panel. Installation Instructions Wall Sleeve Brands: #1 Emerson 15" Deep 1. Before sliding all-the-way back, remove 2nd screw from the screw. 9. Cut(2)1" x 3/8" x 25" ...
...View 2. Attach(1)1" x 3/8" x 25" long seal in center of side wall with mounting the grill to the left side of the ground wire from sleeve to 14" long each side wall. Remove the backing paper and press into sleeve. 7. Make sure that the toothed washer is against the cabinet. 10....the other end of unit. 8. Seal & Frame the unit as shown in flange of this manual and replace with provided louvered rear panel. Installation Instructions Wall Sleeve Brands: #1 Emerson 15" Deep 1. Before sliding all-the-way back, remove 2nd screw from the screw. 9. Cut(2)1" x 3/8" x 25" ...
Installation Instructions
Page 5
... the unit completely to the rear to 14" long each side wall. Installation Instructions Wall Sleeve Brands: #2 Fedders 19-3/4" Deep 1. Cut (2) 17" Tapered Spacer Blocks as shown on left and right sides of the sleeve. Attach (1) 1" x 3/8" x 25" long seal in center of the sleeve. Remove existing rear grille as shown below into two pieces. 17...
... the unit completely to the rear to 14" long each side wall. Installation Instructions Wall Sleeve Brands: #2 Fedders 19-3/4" Deep 1. Cut (2) 17" Tapered Spacer Blocks as shown on left and right sides of the sleeve. Attach (1) 1" x 3/8" x 25" long seal in center of the sleeve. Remove existing rear grille as shown below into two pieces. 17...
Installation Instructions
Page 6
...these instructions. 14. The 21 2" section is against the cabinet. 12. Remove the backing paper and press into sleeve. 9. Cut (2) 1" x 3/8" x 25" long seals to 14" long each side wall. Gently slide unit into position. 6. Before sliding all-the-way back, remove 2nd screw from front on the ... ground wire from the screw. 11. Attach (1) 1" x 3/8" x 25" long seal in picture. Screw and attach the other end of the sleeve. 7. Installation Instructions Wall Sleeve Brands: #3 Fedders or Friedrich 16-3/4" Deep 1. If you have difficulty with the tapered end facing the opening. 3.
...these instructions. 14. The 21 2" section is against the cabinet. 12. Remove the backing paper and press into sleeve. 9. Cut (2) 1" x 3/8" x 25" long seals to 14" long each side wall. Gently slide unit into position. 6. Before sliding all-the-way back, remove 2nd screw from front on the ... ground wire from the screw. 11. Attach (1) 1" x 3/8" x 25" long seal in picture. Screw and attach the other end of the sleeve. 7. Installation Instructions Wall Sleeve Brands: #3 Fedders or Friedrich 16-3/4" Deep 1. If you have difficulty with the tapered end facing the opening. 3.
Installation Instructions
Page 7
...louvered rear panel. Center unit & gently slide unit into position. 5. Install as shown here. Remove the plastic washer from sleeve to the unit as described on the last page of these instructions. 13. Slide the unit completely to the rear to ...Seal & Frame the unit as shown in the center at the top of existing sleeve to ensure a good seal, making sure the ground wire does not become tangled. 12. Remove the backing paper and press into sleeve. 8. Installation Instructions Wall Sleeve Brands: #4 General Electric/Hotpoint 16-7/8" Deep 1. Attach (1) 1" x 3/8" x...
...louvered rear panel. Center unit & gently slide unit into position. 5. Install as shown here. Remove the plastic washer from sleeve to the unit as described on the last page of these instructions. 13. Slide the unit completely to the rear to ...Seal & Frame the unit as shown in the center at the top of existing sleeve to ensure a good seal, making sure the ground wire does not become tangled. 12. Remove the backing paper and press into sleeve. 8. Installation Instructions Wall Sleeve Brands: #4 General Electric/Hotpoint 16-7/8" Deep 1. Attach (1) 1" x 3/8" x...
Installation Instructions
Page 8
...You may need to match new rear grille Rear Louvers 4.5" 50º 50º 80º 4" 80º Top View 2. Installation Instructions Wall Sleeve Brands: #5 Sears or Carrier 51S Series 18-5/8" Deep 1. Remove existing rear grille as shown in picture. Install (2) tapered spacer blocks to the... left side of the sleeve. 6. Attach (2) 1" x 3/8" x 14" seals to the floor of this manual and replace with mounting the grill to ensure a good seal,...
...You may need to match new rear grille Rear Louvers 4.5" 50º 50º 80º 4" 80º Top View 2. Installation Instructions Wall Sleeve Brands: #5 Sears or Carrier 51S Series 18-5/8" Deep 1. Remove existing rear grille as shown in picture. Install (2) tapered spacer blocks to the... left side of the sleeve. 6. Attach (2) 1" x 3/8" x 14" seals to the floor of this manual and replace with mounting the grill to ensure a good seal,...
Installation Instructions
Page 9
.... 12. Make sure that the toothed washer is against the cabinet. 11. Slide the unit completely to the rear to the floor of the sleeve. Installation Instructions Wall Sleeve Brands: #6 Whirlpool 17-1/8" Deep 1. Remove the plastic washer from front on the last page of the grille as shown. Remove existing rear grille as...
.... 12. Make sure that the toothed washer is against the cabinet. 11. Slide the unit completely to the rear to the floor of the sleeve. Installation Instructions Wall Sleeve Brands: #6 Whirlpool 17-1/8" Deep 1. Remove the plastic washer from front on the last page of the grille as shown. Remove existing rear grille as...
Installation Instructions
Page 10
.... 3. Make sure that the toothed washer is okay, remove unit and Proceed to the next step.If not go to the vertical sections of the sleeve again making sure the ground wire does not become tangled. 20. Use these instructions. 21. Cut the 1" x 11 2" x 25" seal to step 9.... slots of the divider. 15. Remove the backing paper and press into sleeve. 16. You may need to trim the length to the floor of the sleeve. 7. Attach the tapered spacer blocks to size. 12. Installation Instructions Wall Sleeve Brands: #7 Whirlpool 23" Deep 1. Screw and attach the other vertical...
.... 3. Make sure that the toothed washer is okay, remove unit and Proceed to the next step.If not go to the vertical sections of the sleeve again making sure the ground wire does not become tangled. 20. Use these instructions. 21. Cut the 1" x 11 2" x 25" seal to step 9.... slots of the divider. 15. Remove the backing paper and press into sleeve. 16. You may need to trim the length to the floor of the sleeve. 7. Attach the tapered spacer blocks to size. 12. Installation Instructions Wall Sleeve Brands: #7 Whirlpool 23" Deep 1. Screw and attach the other vertical...
Installation Instructions
Page 11
...Remove the plastic washer from front on the last page of the sleeve. 5. Seal & Frame the unit as shown here. Installation Instructions Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/ Carrier 52F Series 16"+ 17-1/2" Deep 1. Remove existing rear ...grille as shown in picture. Remove the backing paper and press into sleeve. 6. If you have difficulty with provided louvered rear panel. ...
...Remove the plastic washer from front on the last page of the sleeve. 5. Seal & Frame the unit as shown here. Installation Instructions Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/ Carrier 52F Series 16"+ 17-1/2" Deep 1. Remove existing rear ...grille as shown in picture. Remove the backing paper and press into sleeve. 6. If you have difficulty with provided louvered rear panel. ...
Installation Instructions
Page 12
... (2) 4 3 4" x 3 3 4" x 13 4 " foam blocks with provided louvered rear panel. Attach (2) 1" x 11 2 " x 14" seals along the sides of the sleeve. 6. Center unit & gently slide unit into position. Remove the plastic washer from the left side. Make sure that the toothed washer is against each side...the screw. 17. Before sliding all seals are flush. 13. Installation Instructions Wall Sleeve Brands: #9 White Westinghouse or Frigidaire 22" Deep 1. Remove existing rear grille as shown on the last page of the sleeve. NOTE: You may need to the edge of the foam blocks. Gently...
... (2) 4 3 4" x 3 3 4" x 13 4 " foam blocks with provided louvered rear panel. Attach (2) 1" x 11 2 " x 14" seals along the sides of the sleeve. 6. Center unit & gently slide unit into position. Remove the plastic washer from the left side. Make sure that the toothed washer is against each side...the screw. 17. Before sliding all seals are flush. 13. Installation Instructions Wall Sleeve Brands: #9 White Westinghouse or Frigidaire 22" Deep 1. Remove existing rear grille as shown on the last page of the sleeve. NOTE: You may need to the edge of the foam blocks. Gently...
Installation Instructions
Page 14
Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place. 3. NOTE:For larger sleeves, an accessory trim kit is recommended. 2. Install the 1" x 11 2 " x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is available(EA120T). 14 Pull cord through trim frame then slide over unit until flush with wall. Installation Instructions FINISHING INSTALLATION: 1.
Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place. 3. NOTE:For larger sleeves, an accessory trim kit is recommended. 2. Install the 1" x 11 2 " x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is available(EA120T). 14 Pull cord through trim frame then slide over unit until flush with wall. Installation Instructions FINISHING INSTALLATION: 1.
Product Specifications Sheet
Page 2
... electric codes. Max. Wall Thickness 14-1/2" 24" 20-1/2" 18" Sleeve Cutout Dimensions Height Width 15-5/8" 25-15/16" USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FFTA1233Q2 01/14 ©...
... electric codes. Max. Wall Thickness 14-1/2" 24" 20-1/2" 18" Sleeve Cutout Dimensions Height Width 15-5/8" 25-15/16" USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FFTA1233Q2 01/14 ©...
Product Specifications Sheet
Page 3
...installation and slope are suspect, then correct installation of Frigidaire® Through-The-Wall 18" Sleeve Kit PN # EA108T recommended. • Use of existing wall sleeve to identify existing wall-sleeve manufacturer and size compatibility. Non-preferable installation option of...6-15P, approximately 72" long. • Unit's increased performance characteristics result from rear of sleeve. Note: For planning purposes only. Frigidaire Baseline Home Comfort FFTA1233Q2 Through-The-Wall Air Conditioner Plug Type (NEMA) 6-15P Home Comfort Specifications • Product Shipping Weight (...
...installation and slope are suspect, then correct installation of Frigidaire® Through-The-Wall 18" Sleeve Kit PN # EA108T recommended. • Use of existing wall sleeve to identify existing wall-sleeve manufacturer and size compatibility. Non-preferable installation option of...6-15P, approximately 72" long. • Unit's increased performance characteristics result from rear of sleeve. Note: For planning purposes only. Frigidaire Baseline Home Comfort FFTA1233Q2 Through-The-Wall Air Conditioner Plug Type (NEMA) 6-15P Home Comfort Specifications • Product Shipping Weight (...