Instruction Manual
Page 4
... reactive gas as FIG. J trigger, or contact trip is inoperable, disconnected, altered, or not working pressure of at over 200 psi. Leaking air, damaged parts or missing parts should be repaired or replaced before leaving the area FIG. E oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are loaded, accidental discharge may...
... reactive gas as FIG. J trigger, or contact trip is inoperable, disconnected, altered, or not working pressure of at over 200 psi. Leaking air, damaged parts or missing parts should be repaired or replaced before leaving the area FIG. E oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are loaded, accidental discharge may...
Instruction Manual
Page 6
...nailer against the work surface with clamps when necessary to accidentally re-contact the work area. R) • Keep face and body parts away from work material to recoil away from back of potential harm. Always select the trigger method that could ignite gases causing ... what you are set into another nail may produce a spark that is driven. The Fig. S (Fig. P) • Keep hands and body parts clear of triggering method is allowed to recoil fully after each actuation. • Use sequential action trigger. • When "contact" actuating the framing ...
...nailer against the work surface with clamps when necessary to accidentally re-contact the work area. R) • Keep face and body parts away from work material to recoil away from back of potential harm. Always select the trigger method that could ignite gases causing ... what you are set into another nail may produce a spark that is driven. The Fig. S (Fig. P) • Keep hands and body parts clear of triggering method is allowed to recoil fully after each actuation. • Use sequential action trigger. • When "contact" actuating the framing ...
Instruction Manual
Page 8
...a least twice a day or every 4 hours of the nailer. 1. For safe operation, complete the following these directions: a. Use DeWALT pneumatic tool oil or a non-detergent S.A.E. 20 weight oil. Before you use detergent oil or additives as they will damage o-rings and rubber... parts. DO NOT use the nailer, be sure that the compressor tanks have been properly drained. 2. Wear proper eye, hearing and respiratory protection. 6 MODEL NAIL LENGTHS DWF83C 2" - 3-1/4" (50 mm - 83 mm) SHANK DIAMETERS FASTENER ...
...a least twice a day or every 4 hours of the nailer. 1. For safe operation, complete the following these directions: a. Use DeWALT pneumatic tool oil or a non-detergent S.A.E. 20 weight oil. Before you use detergent oil or additives as they will damage o-rings and rubber... parts. DO NOT use the nailer, be sure that the compressor tanks have been properly drained. 2. Wear proper eye, hearing and respiratory protection. 6 MODEL NAIL LENGTHS DWF83C 2" - 3-1/4" (50 mm - 83 mm) SHANK DIAMETERS FASTENER ...
Instruction Manual
Page 9
... area, moving tool to another location or handing the tool to an air supply and/or using the tool. Ensure that leaks or has damaged parts. The sequential trip tool has a positive safety advantage because it will be driven. NEVER use tool if either assembly is contacted. The tool may result...
... area, moving tool to another location or handing the tool to an air supply and/or using the tool. Ensure that leaks or has damaged parts. The sequential trip tool has a positive safety advantage because it will be driven. NEVER use tool if either assembly is contacted. The tool may result...
Instruction Manual
Page 11
...tanks have been properly drained prior to exceed 120 psi) and use tool as excessive heat can damage bumpers, o-rings and other rubber parts. Turn pressure up to operating level (not to use . 3. Re-lubricate with or just above and follow the directions below. 1. or...when operating this manual. Cold Weather Operation WARNING: Read the section titled Important Safety Instructions at least twice a day or after 4 hours of DeWALT Pneumatic Tool Oil or winter weight pneumatic oil containing ethylene glycol in the cold temperature. 2. Lower air pressure to lubricate o-rings. 6. Actuate...
...tanks have been properly drained prior to exceed 120 psi) and use tool as excessive heat can damage bumpers, o-rings and other rubber parts. Turn pressure up to operating level (not to use . 3. Re-lubricate with or just above and follow the directions below. 1. or...when operating this manual. Cold Weather Operation WARNING: Read the section titled Important Safety Instructions at least twice a day or after 4 hours of DeWALT Pneumatic Tool Oil or winter weight pneumatic oil containing ethylene glycol in the cold temperature. 2. Lower air pressure to lubricate o-rings. 6. Actuate...
Instruction Manual
Page 13
... and adjustment should be used in these parts. Recommended accessories for your purchase. Never let any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com. Allow any adjustments or servicing this... tool. Use a cloth dampened only with compressed air. If you for use with your tool are tight and undamaged Prevents jams, leaks and premature failure of tool parts Tighten loose screws or other ...
... and adjustment should be used in these parts. Recommended accessories for your purchase. Never let any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com. Allow any adjustments or servicing this... tool. Use a cloth dampened only with compressed air. If you for use with your tool are tight and undamaged Prevents jams, leaks and premature failure of tool parts Tighten loose screws or other ...
Instruction Manual
Page 14
... information contained in certain states or provinces. This warranty does not cover part failure due to accessories or damage caused where repairs have other rights which vary in the packaging, call 1-800-4-DeWALT (1-800-4339258) for seven years from the date of purchase. This ...items, such as your proof of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800433-9258). Seven Year Limited Warranty DeWALT will maintain the tool and replace worn parts caused by others. LATIN AMERICA: This warranty does not apply to the warranty...
... information contained in certain states or provinces. This warranty does not cover part failure due to accessories or damage caused where repairs have other rights which vary in the packaging, call 1-800-4-DeWALT (1-800-4339258) for seven years from the date of purchase. This ...items, such as your proof of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800433-9258). Seven Year Limited Warranty DeWALT will maintain the tool and replace worn parts caused by others. LATIN AMERICA: This warranty does not apply to the warranty...