Dewalt DWF83C Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWF83C manuals!
Problems with Dewalt DWF83C?
Ask a Question
Free Dewalt DWF83C manuals!
Problems with Dewalt DWF83C?
Ask a Question
Popular Dewalt DWF83C Manual Pages
Instruction Manual - Page 3
...DeWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DeWALT (1-800-433-9258)
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Important Safety Instructions
WARNING: Do not operate this unit until you read the manual... must
conform with the characters "Z87.1".
Condensation from this instruction manual for each signal word. Definitions: Safety Guidelines
The definitions below describe the...
Instruction Manual - Page 4
.... G
or passing the tool to the air supply. If the contact trip is adjusted when the tool is connected to become inoperable. Leaking air, damaged parts or missing parts should be repaired or replaced before leaving the area
FIG. I otherwise cause the tool, trigger, or contact trip to the air supply and...
Instruction Manual - Page 5
... nails may follow the grain of the tool or top cap as a hammer. N)
FIG. P using the nailer.... No horseplay! When tool is set so that
3 L)
• Always keep fingers clear of nails. (Fig. Be aware that ...nails can cause you or a co-worker. O)
• Be aware of balance or footing. Loss of material. Drive the
nail perpendicular to the grain to the Maintenance and Repairs...
Instruction Manual - Page 6
..., especially
when nailing into live electrical...manual for triggering options. Fasteners
driven into hard or dense material. U)
• Stay alert, watch what you are set...parts away from work areas. Unwanted fasteners may produce a spark that is allowed to recoil fully after each actuation.
• Use sequential action trigger.
• When "contact" actuating the framing nailer...
Instruction Manual - Page 7
...:
• ANSI Z87.1 eye protection (CAN/CSA/Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection. SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
E
COMPONENTS (FIG. 1)
A. Canister
C
C. Your risk from chemically-treated lumber.
To reduce your exposure to these exposures varies, depending on how often you...
Instruction Manual - Page 8
... (3.85 kg) 2.5" (64 mm) 70 - 120 psig
6.5 cfm @ 80 psi 1 Coil (200-300 Nails)
Nail Specifications
NOTE: Use only DeWALT approved fasteners. For safe operation, complete the following these directions: a. Use DeWALT pneumatic tool oil or a non-detergent S.A.E. 20
weight oil. b. FIG. 2
FIG. 3
3.
MODEL NAIL LENGTHS
DWF83C 2" - 3-1/4" (50 mm - 83 mm)
SHANK DIAMETERS
FASTENER COLLATION...
Instruction Manual - Page 9
...1. Do not use a tool that leaks or has damaged parts.
In contact mode tool will allow rapid fastener placement on...assembly. Sequential Trip: Sequential trip requires the operator to Tool Specifications.
7.
The tool may result.
Push and hold the contact... trip restrained in sequential trip
mode:
F
1. To operate the nailer in the up position.
6. TO CHANGE OPERATING MODES (FIG. ...
Instruction Manual - Page 10
... down door latch and swing door/canister cover outward.
2.
Nails will fire a nail every
time the contact trip is depressed.
To operate the nailer in the driver channel. FIG. 6b
8 The canister contains an adjustable nail platform on the post and twist to three nail settings.
English
WARNING: A nail will fire each time the trigger is depressed as...
Instruction Manual - Page 11
...nail drive depth from flush with DeWALT Pneumatic Tool Oil or winter weight
pneumatic oil containing ethylene glycol in the slot on the nose.)
Depth Setting...Instructions at least twice a day or after 4 hours of the nailer. Hot Weather Operation
Tool should operate normally.
Close the door: Check that latch engages. (If it does not engage,
check that the nail... parts....this manual. Swing...
Instruction Manual - Page 12
...1/4" (6.4 mm) punch and hammer. When the nail is jammed between the driver and nose casting force driver
J
blade back to jam frequently in nosepiece, have tool serviced by an authorized DeWALT service center.
10
J
FIG. 8
I ). Remove nails from you and follow these instructions to clear:
1. Reassemble in reverse order. If nail still can be removed, remove the canister...
Instruction Manual - Page 13
... risk of serious personal injury, remove nails from your purchase. To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be hazardous.
Register Online
Thank you need assistance in these parts. Accessories
WARNING: Since accessories, other than those offered by a DeWALT factory service center, a DeWALT authorized service center or other drain valves on...
Instruction Manual - Page 14
no questions asked.
This warranty does not cover part failure due to products sold in Latin America, see country specific warranty information contained in certain states or provinces. In addition to the warranty, DeWALT tools are covered by our:
1 YEAR FREE SERVICE DeWALT will maintain the tool and replace worn parts caused by normal use, for free, any...
Instruction Manual - Page 15
... leaks
Main seal or o-ring damaged, debris Replace gasket/o-rings using framing nailer o-ring repair kit
Exhaust port blocked or clogged Disconnect air, remove exhaust plate from top of serious personal injury, remove fasteners from canister before making any adjustments or servicing this tool. English
TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART...
Instruction Manual - Page 16
...Worn piston o-ring
Replace O-ring using Framing Nailer O-Ring Repair Kit
Fasteners jam in tool
Driver channel in nosepiece worn Replace nosepiece
Wrong size/ angle fasteners
Use only recommended fasteners
Worn driver blade
Replace driver blade
Nosepiece screws loose
Tighten nosepiece screws using appropriate hex wrench
Nails not feeding properly
Ensure nails are feeding properly through...
Dewalt DWF83C Reviews
We have not received any reviews for Dewalt yet.