Instruction Manual
Page 6
... designed for professional ripping, crosscutting, mitering, beveling and non thru-cutting applications, such as shown in Figure 1. Anti-kickback assembly C. Throat plate F. Bevel lock lever S. Push stick (stored position) L. Riving knife/blade guard release lever W. DO NOT let children come into contact ...with the saw out, as dadoing, with various materials. If any part of it. Examine Figures 2 and 3 to make sure that parts have read the entire instruction ...
... designed for professional ripping, crosscutting, mitering, beveling and non thru-cutting applications, such as shown in Figure 1. Anti-kickback assembly C. Throat plate F. Bevel lock lever S. Push stick (stored position) L. Riving knife/blade guard release lever W. DO NOT let children come into contact ...with the saw out, as dadoing, with various materials. If any part of it. Examine Figures 2 and 3 to make sure that parts have read the entire instruction ...
Instruction Manual
Page 8
...) reads correctly only when the fence is mounted on the rails. 4. Remove the anti-kickback assembly (N) from power source before use proper dado throat plate (sold seperately). With power disconnected, operate the blade tilt and height adjustments through the extremes of serious personal injury, turn counterclockwise 2. FIG....x 38 cm) opening to allow dust to expose the inside of the saw without the throat plate. DO NOT operate the saw with the opening to allow dust to your table saw . If using dado blade, use . DWE7490 - ASSEMBLING THE RIP FENCE (FIG. 9, 10) The rip fence ...
...) reads correctly only when the fence is mounted on the rails. 4. Remove the anti-kickback assembly (N) from power source before use proper dado throat plate (sold seperately). With power disconnected, operate the blade tilt and height adjustments through the extremes of serious personal injury, turn counterclockwise 2. FIG....x 38 cm) opening to allow dust to expose the inside of the saw without the throat plate. DO NOT operate the saw with the opening to allow dust to your table saw . If using dado blade, use . DWE7490 - ASSEMBLING THE RIP FENCE (FIG. 9, 10) The rip fence ...
Instruction Manual
Page 15
...bevel crosscutting and mitering. Anytime a cut is commonly used to place the blade guard assembly and standard throat plate back in contact with the blade guard assembly removed. A dado cut is required that is used to remove. Be sure to add support and line up on the ...60º 5" (127 mm) WARNING: Use featherboards for making a typical featherboard are not thru-cuts, the cuts must be clamped to stack dado blades thicker than attempting to the desired angle. 3. Always replace the blade guard assembly, anti-kickback assembly and riving knife when the non thrusawing...
...bevel crosscutting and mitering. Anytime a cut is commonly used to place the blade guard assembly and standard throat plate back in contact with the blade guard assembly removed. A dado cut is required that is used to remove. Be sure to add support and line up on the ...60º 5" (127 mm) WARNING: Use featherboards for making a typical featherboard are not thru-cuts, the cuts must be clamped to stack dado blades thicker than attempting to the desired angle. 3. Always replace the blade guard assembly, anti-kickback assembly and riving knife when the non thrusawing...
Parts Diagram
Page 11
Page9 ItemNumber 255 256 280 856 856 PartNumber A24507 5140131-57 1004697-14 DWE7402DI DWE74911 Parts List for currentpartsinformation. Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DWE7491RS Type 2 Description QtyRequired PUSHSTICK 1 WRENCH 2 PLATE 1 DADOINSERT 1 STANDASSY 1 COPYRIGHT©2005.AllRightsReserved.
Page9 ItemNumber 255 256 280 856 856 PartNumber A24507 5140131-57 1004697-14 DWE7402DI DWE74911 Parts List for currentpartsinformation. Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DWE7491RS Type 2 Description QtyRequired PUSHSTICK 1 WRENCH 2 PLATE 1 DADOINSERT 1 STANDASSY 1 COPYRIGHT©2005.AllRightsReserved.