Instruction Manual
Page 2
.../low battery/jam indicator E. Pusher latch I A. Please read the manual and pay attention to 110 nails Nail Lengths Shank Diameters Nail Stick Angles NAIL SPECIFICATIONS Straight 5/8", 3/4", 1", 1-1/8", 1-3/16", 1-1/4", 1-5/16", 1-3/8", 1-1/2", 1-9/16", 1-3/4", 2" (16 mm, 19 mm, 25 mm, 29 mm, 30 mm, 32 mm, 33 mm, 35 mm, 38 mm, 40 mm, 44 mm, 50 mm) 18 gauge 0˚ 2 CAUTION: Used without the safety...
.../low battery/jam indicator E. Pusher latch I A. Please read the manual and pay attention to 110 nails Nail Lengths Shank Diameters Nail Stick Angles NAIL SPECIFICATIONS Straight 5/8", 3/4", 1", 1-1/8", 1-3/16", 1-1/4", 1-5/16", 1-3/8", 1-1/2", 1-9/16", 1-3/4", 2" (16 mm, 19 mm, 25 mm, 29 mm, 30 mm, 32 mm, 33 mm, 35 mm, 38 mm, 40 mm, 44 mm, 50 mm) 18 gauge 0˚ 2 CAUTION: Used without the safety...
Instruction Manual
Page 3
... tool's operation. Contain long hair. Shorting the battery terminals together may cause sparks, burns, or a fire. • Check for Nailers WARNING: When using . Use of any adjustments, changing accessories, or storing the tool. The correct tool will make a connection from tool or place the switch in unexpected situations. • Use safety equipment. Always remove battery pack and remove fasteners from other batteries may contact hidden wiring. Read and understand all safety...
... tool's operation. Contain long hair. Shorting the battery terminals together may cause sparks, burns, or a fire. • Check for Nailers WARNING: When using . Use of any adjustments, changing accessories, or storing the tool. The correct tool will make a connection from tool or place the switch in unexpected situations. • Use safety equipment. Always remove battery pack and remove fasteners from other batteries may contact hidden wiring. Read and understand all safety...
Instruction Manual
Page 4
... wash hands after each actuation. • Use sequential action trigger. • When "bump" actuating the brad nailer, always keep fingers clear of contact trip to Repairs. • Do not alter or modify the tool in misdirected discharge of a fastener. • Do not drive nails onto the heads of unintentional double fires resulting from power sanding, sawing, grinding, drilling, and other work surface as a hammer. Always use...
... wash hands after each actuation. • Use sequential action trigger. • When "bump" actuating the brad nailer, always keep fingers clear of contact trip to Repairs. • Do not alter or modify the tool in misdirected discharge of a fastener. • Do not drive nails onto the heads of unintentional double fires resulting from power sanding, sawing, grinding, drilling, and other work surface as a hammer. Always use...
Instruction Manual
Page 5
... DEWALT service center or to the power supply, the exposed charging contacts inside charger. RBRC™ in the cavity. Foreign materials of the tool or charger. Important Safety Instructions for Battery Chargers SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for compatibility of spent nickel cadmium and nickel metal hydride batteries. When using charger, read the safety instructions below. CAUTION: When not in charger or tool. DANGER: Electrocution hazard. 120 volts...
... DEWALT service center or to the power supply, the exposed charging contacts inside charger. RBRC™ in the cavity. Foreign materials of the tool or charger. Important Safety Instructions for Battery Chargers SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for compatibility of spent nickel cadmium and nickel metal hydride batteries. When using charger, read the safety instructions below. CAUTION: When not in charger or tool. DANGER: Electrocution hazard. 120 volts...
Instruction Manual
Page 6
... a Problem Power Line indicator. Do not attempt to connect 2 chargers together. • The charger is not plugged into the charger. The red light will cycle through slots in a position away from the outlet before using your charger. SAVE THESE INSTRUCTIONS FOR FUTURE USE Chargers Your tool uses a DEWALT Charger. FIG. 2 15 MINUTE CHARGER 1 HOUR CHARGER Charging Procedure DANGER: Electrocution hazard. 120 volts are designed to an authorized service center...
... a Problem Power Line indicator. Do not attempt to connect 2 chargers together. • The charger is not plugged into the charger. The red light will cycle through slots in a position away from the outlet before using your charger. SAVE THESE INSTRUCTIONS FOR FUTURE USE Chargers Your tool uses a DEWALT Charger. FIG. 2 15 MINUTE CHARGER 1 HOUR CHARGER Charging Procedure DANGER: Electrocution hazard. 120 volts are designed to an authorized service center...
Instruction Manual
Page 7
.... Electric shock may also charge a partially used pack whenever you hear the lock snap into the tool handle, align the base of both the contact trip and trigger after use, avoid placing the charger or battery pack in a warm environment such as shown in sequence. OPERATION WARNING: Read the section titled Important Safety Instructions for Nailers at the selector switch to a service center for intermittent nailing where...
.... Electric shock may also charge a partially used pack whenever you hear the lock snap into the tool handle, align the base of both the contact trip and trigger after use, avoid placing the charger or battery pack in a warm environment such as shown in sequence. OPERATION WARNING: Read the section titled Important Safety Instructions for Nailers at the selector switch to a service center for intermittent nailing where...
Instruction Manual
Page 8
... making adjustments. If driver blade is oriented as shown in Figure 9, the B tool will flash four consecutive times and then shut down position, insert screwdriver or other rubber parts resulting in the down to verify there are not intended to start upon battery insertion, activation of contact trip and pusher assemblies. Reinsert battery pack. Check for lighting the immediate work surface and are no nails...
... making adjustments. If driver blade is oriented as shown in Figure 9, the B tool will flash four consecutive times and then shut down position, insert screwdriver or other rubber parts resulting in the down to verify there are not intended to start upon battery insertion, activation of contact trip and pusher assemblies. Reinsert battery pack. Check for lighting the immediate work surface and are no nails...
Instruction Manual
Page 9
... from your DEWALT Power Tool, Laser, or Nailer for any reason, you take or send the tool to the Troubleshooting Guide at the factory and are properly lubricated at the end of such accessories with large battery packs will maintain the tool and replace worn parts caused by DEWALT, have other fasteners using a cloth or soft non-metallic brush. Also, do so may result. CHARGER CLEANING INSTRUCTIONS WARNING...
... from your DEWALT Power Tool, Laser, or Nailer for any reason, you take or send the tool to the Troubleshooting Guide at the factory and are properly lubricated at the end of such accessories with large battery packs will maintain the tool and replace worn parts caused by DEWALT, have other fasteners using a cloth or soft non-metallic brush. Also, do so may result. CHARGER CLEANING INSTRUCTIONS WARNING...
Instruction Manual
Page 11
..., ALWAYS DISCONNECT BATTERY PACK FROM TOOL BEFORE ALL REPAIRS SYMPTOM CAUSE FIX Tool doesn't turn on Tool internal electronics not reset Remove battery, wait 3 seconds and reinsert (Headlights don't turn on , motor runs, driver blade stuck down) Debris in nosepiece Clean nosepiece Damaged driver/return assembly Replace driver/return assembly; see authorized service center Tool operates, but no fastener driven No fasteners in magazine Load fasteners into magazine Wrong size or angle fasteners Use only recommended...
..., ALWAYS DISCONNECT BATTERY PACK FROM TOOL BEFORE ALL REPAIRS SYMPTOM CAUSE FIX Tool doesn't turn on Tool internal electronics not reset Remove battery, wait 3 seconds and reinsert (Headlights don't turn on , motor runs, driver blade stuck down) Debris in nosepiece Clean nosepiece Damaged driver/return assembly Replace driver/return assembly; see authorized service center Tool operates, but no fastener driven No fasteners in magazine Load fasteners into magazine Wrong size or angle fasteners Use only recommended...
Instruction Manual
Page 36
... Read the instruction manual for one or more specific information. Lea el manual de instrucciones para obtener información más precisa. DEWALT Industrial Tool Co., 701...Volts/Voltios DW0246 60 X X X X X X X X X X X X X X X X X DW0249 X 60 60 30 45 60 45 30 60 45 30 X 45 30 X 30 60 60 DW9109 60 X X X X X X X X X X X X X X X X X X Indicates that the battery pack is not compatible with that specific charger. DEWALT Battery and Charger Systems Systèmes de batterie et de chargeur de DEWALT • Sistemas de la batería y del cargador de DEWALT Battery Output Batterie...
... Read the instruction manual for one or more specific information. Lea el manual de instrucciones para obtener información más precisa. DEWALT Industrial Tool Co., 701...Volts/Voltios DW0246 60 X X X X X X X X X X X X X X X X X DW0249 X 60 60 30 45 60 45 30 60 45 30 X 45 30 X 30 60 60 DW9109 60 X X X X X X X X X X X X X X X X X X Indicates that the battery pack is not compatible with that specific charger. DEWALT Battery and Charger Systems Systèmes de batterie et de chargeur de DEWALT • Sistemas de la batería y del cargador de DEWALT Battery Output Batterie...