Dewalt DW369CSK Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt DW369CSK manuals!
Problems with Dewalt DW369CSK?
Ask a Question
Free Dewalt DW369CSK manuals!
Problems with Dewalt DW369CSK?
Ask a Question
Popular Dewalt DW369CSK Manual Pages
Instruction Manual - Page 3
... gloves away from heat, oil,
sharp edges or moving parts. Minimum Gage for Cord Sets
Volts
Total Length of electric shock. DW368/605266 7/2/02 11:50 AM Page 4
English
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:
1-800-4-DEWALT (1-800-433-9258)
General Safety Instructions
WARNING!
Instruction Manual - Page 4
... correct tool will do the job better and safer at the rate for Circular Saws
DANGER! Holding the work . TOOL USE AND CARE • Use clamps or other part, at all angles and depth of cut by qualified repair
personnel. Follow instructions in the Maintenance section of the tool in tools that cannot be controlled...
Instruction Manual - Page 5
...walls or other sawing, the lower...saw blade in the cut . Do not use a rip fence or straight edge guide. Unsharpened or improperly set... KICKBACK.
2 Support must be avoided... or misaligned
saw blade, causing an uncontrolled saw to lift up...the saw and position your saw,...saw...vs. The protruding blade may occur. DW368/605266 7/2/02 11:50 AM Page 2
English
sluggishly due to damaged parts...
Instruction Manual - Page 6
...off . • SUPPORT LARGE PANELS. To ...saw shall be encountered, DO NOT TOUCH ANY METAL PARTS...guide when ripping. Some examples of blade pinching and kickback.
DW368/605266 7/2/02 11:50 AM Page 3
English
SAVE THESE INSTRUCTIONS
Additional Specific Instructions
CAUTION: When cutting into your tool may include the following symbols. Under some conditions and duration of the saw...
Instruction Manual - Page 7
... and Setup
ATTACHING AND REMOVING BLADES (Fig. 1-3)
DISCONNECT PLUG FROM POWER SUPPLY. Tighten blade screw clockwise with nameplate marking. 120 Volts AC/DC means your saw will operate on saw spindle.
Your DEWALT saw spindle with 5/8" round arbor holes.
1. Blade bolt
Motor
B
A
D
E
C
Your DEWALT tool is equipped to hold both washers must face the blade.
DW368/605266...
Instruction Manual - Page 8
... FROM POWER SUPPLY.
The full range of a calibrated quadrant (A) and a knob. Replace outer clamp washer. Replace and tighten the blade bolt as much tooth projects beyond the material. Your saw at the proper cutting depth keeps blade friction to be cut (Figure 5). Setting the saw is from between the blade teeth, results in cooler, faster...
Instruction Manual - Page 9
... and tilt the shoe to guide the saw along cutting lines penciled on the front of the indicator.
Operation
SWITCH (DETAIL PAGE 4) Pull the trigger switch to 56 degrees. DW368/605266 7/2/02 11:50 AM... you will hear a click and feel the shoe stop at 1/4" (6.35 mm) spacing. To set the saw is graduated in any way.
Retighten knob firmly by aligning the pointer with a Bevel Detent feature...
Instruction Manual - Page 10
... load on that it .
Place the work . The saw forward at a speed which is solidly supported, not on the section that will fall off the end of the cutting area so that part of the work .
DON'T support board or panel away from below. down. CUTTING Support the work so that is up on which...
Instruction Manual - Page 11
...lumber (material treated with the blade in the kerf. The saw is pinched or bound tightly by the kerf closing down . IMPROPER WORKPIECE SUPPORT
A.
The falling cut off strip can sag or twist ...DW368/605266 7/2/02 11:50 AM Page 8
English
Kickback
When the saw blade becomes pinched or twisted in the cut, kickback can result in blade twist. IMPROPER DEPTH OF CUT SETTING ON SAW
Using the saw...
Instruction Manual - Page 12
... organizations, always using identical replacement parts.(See Brushes section for brush replacement information)
brush in the same orientation in about 2 seconds, the
1.
If after inspecting or servicing brushes. Using an allen wrench, turn the saw on its side, and retract the lower guard.
3. SHOE ADJUSTMENT DISCONNECT PLUG FROM POWER SUPPLY.
problem may be allowed to
Cleaning...
Instruction Manual - Page 13
... local service center.
REPLACE IF DAMAGED. PRESSURE TREATED/WET LUMBER - 5/8" Round arbor, 20 teeth Coated -
We will cause slow, inefficient cutting, overload on the saw through the cut, when the motor is straining, or when excessive heat is no longer easy to the desired location, about 1/8 of kickback. This warranty gives you specific legal...
Instruction Manual - Page 14
...: 30 DAY NO RISK SATISFACTION GUARANTEE
If you are missing, call 1-800-4-DEWALT for a full refund. English
DW368/605266 7/2/02 11:50 AM Page 11
In addition to the participating seller within 30 days for a free replacement.
11 FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are not completely satisfied with...
Parts Diagram - Page 2
... 24 25 26 28 29 30 31
Part Number
Parts List for current parts information.
Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for DW369CSK Type 1
Description
Qty Required
389530-03SV
ARMATURE & BRGS
1
629392-00
FIELD
1
N032830
BRUSH & LEAD
2
398943-00
TORSION SPRING
2
389512-01
BRUSH RING ASM
1
389525-00
SWITCH
1
389510...
Parts Diagram - Page 3
Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for DW369CSK Type 1
Description
Qty Required
145347-00
LEVER,LOCK
1
152014-00
WASHER
1
152211-00
RING,RETAINING
1... 54 55 56 57 60 63 68 74 75 76 78 91
Part Number
Parts List for current parts information. Page 2 LABEL
1
053650-03
TERMINAL
1
COPYRIGHT© 2005. All Rights Reserved.
Parts Diagram - Page 4
... information. Please visit www.dewaltservicenet.com for DW369CSK Type 1
Description
Qty Required
No Longer Available
1
RIP FENCE
1
WRENCH
1
TERMINAL,MALE
1
TERMINAL,FEMALE
1
LEVER
1
SHAFT
1
SCREW,M5X20
1
WASHER
1
GREASE:4 LB CAN
1
7-1/4 24T SAW BL -
CARDED
1
KITBOX
1
COPYRIGHT© 2005. All Rights Reserved. Parts list, pricing, and availability subject to...
Dewalt DW369CSK Reviews
Do you have an experience with the Dewalt DW369CSK that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!