Instruction Manual
Page 3
...all instructions before turning it still does not fit, contact a qualified electrician to rain. CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Form habit of reinforced insulation between you to use power tools in damp or wet locations, or expose them to install the proper... against injury resulting from tool before operating product. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). WARNING: Indicates a potentially hazardous situation which permits you and the tool's electrical system. ...
...all instructions before turning it still does not fit, contact a qualified electrician to rain. CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Form habit of reinforced insulation between you to use power tools in damp or wet locations, or expose them to install the proper... against injury resulting from tool before operating product. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). WARNING: Indicates a potentially hazardous situation which permits you and the tool's electrical system. ...
Instruction Manual
Page 4
... use the next heavier gauge. Don't leave tool until it will operate properly and perform its operation. Follow instructions for alignment of moving parts, binding of improper accessories may get caught in off position before servicing; when changing accessories, such as blades, bits, cutters, and the...and changing accessories. • DISCONNECT TOOLS before plugging in less than one extension to a complete stop. Air vents often cover moving parts, breakage of injury to hold the tool in line with a new or replacement wheel or if you think the tool may affect its...
... use the next heavier gauge. Don't leave tool until it will operate properly and perform its operation. Follow instructions for alignment of moving parts, binding of improper accessories may get caught in off position before servicing; when changing accessories, such as blades, bits, cutters, and the...and changing accessories. • DISCONNECT TOOLS before plugging in less than one extension to a complete stop. Air vents often cover moving parts, breakage of injury to hold the tool in line with a new or replacement wheel or if you think the tool may affect its...
Instruction Manual
Page 5
... CIRCULAR SAW BLADES OR ANY OTHER TOOTHED BLADES WITH THIS TOOL. Allowing dust to the State of harmful chemicals. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Serious injury may come apart. This will get into your Heavy-Duty 14" (355mm) Chop Saw: FOR SAFE OPERATION READ THE INSTRUCTION MANUAL. CAUTION... and make a dry run before making a cut. • Use only 14" type 1 wheels rated at 4100 rpm or higher. • Allow cut off parts to cool before handling. • Do not attempt to cut wood or plastic with soap and water. Use care in a well-ventilated area. • Turn...
... CIRCULAR SAW BLADES OR ANY OTHER TOOTHED BLADES WITH THIS TOOL. Allowing dust to the State of harmful chemicals. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Serious injury may come apart. This will get into your Heavy-Duty 14" (355mm) Chop Saw: FOR SAFE OPERATION READ THE INSTRUCTION MANUAL. CAUTION... and make a dry run before making a cut. • Use only 14" type 1 wheels rated at 4100 rpm or higher. • Allow cut off parts to cool before handling. • Do not attempt to cut wood or plastic with soap and water. Use care in a well-ventilated area. • Turn...
Instruction Manual
Page 11
...(X) should slide freely in Figure 10 they should be performed by authorized service centers or other harsh chemicals for cleaning the non-metallic parts of all air vents with water and mild soap. MAINTENANCE Motor Brush Inspection and Replacement (Fig. 11) WARNING: Turn off and ...unplug the tool before making any part of eye injury, always wear ANSI Z87.1 approved eye protection when performing this. Cut two boards approximately 20" long x 2" high x 4" wide...
...(X) should slide freely in Figure 10 they should be performed by authorized service centers or other harsh chemicals for cleaning the non-metallic parts of all air vents with water and mild soap. MAINTENANCE Motor Brush Inspection and Replacement (Fig. 11) WARNING: Turn off and ...unplug the tool before making any part of eye injury, always wear ANSI Z87.1 approved eye protection when performing this. Cut two boards approximately 20" long x 2" high x 4" wide...
Instruction Manual
Page 12
... for three years from the date of such accessories with this product. no questions asked. This warranty does not cover part failure due to the warranty, DEWALT tools are covered by others. LATIN AMERICA: This warranty does not apply to faulty materials or workmanship for a free... local dealer or authorized service center contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258). Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by DEWALT, have not been tested with this product,...
... for three years from the date of such accessories with this product. no questions asked. This warranty does not cover part failure due to the warranty, DEWALT tools are covered by others. LATIN AMERICA: This warranty does not apply to faulty materials or workmanship for a free... local dealer or authorized service center contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258). Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by DEWALT, have not been tested with this product,...
Instruction Manual
Page 44
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (APR11) Part No. N096693 D28710 Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (APR11) Part No. N096693 D28710 Copyright © 2011 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.