D-Link DWL-P1012 - Power Injector - 185 Watt Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DWL-P1012 manuals!
Problems with D-Link DWL-P1012?
Ask a Question
Free D-Link DWL-P1012 manuals!
Problems with D-Link DWL-P1012?
Ask a Question
Popular D-Link DWL-P1012 Manual Pages
Product Manual - Page 4
Discovery List 13 Monitor List 14 Device Setting 15 Toolbar ...16 Configuring the DWL-P1012 17 Login ...17 Setup Menu 20
SNMP Setting 21 PoE Setting 25 Schedule 27 Port Group 29 SNTP 31 Device Status 32 System Setting 35 RTC Time 36 Trap Setting 38 Set Password 39 Backup Setting 39 Reset Setting 39 Logout 40 WARRANTY ...41
ii
Product Manual - Page 5
... and Setup
Identifying External Components
Configure the Midspan
Warranty
Describes the Midspan and its features. The Power over unused pairs of the DWL-P1012, most importantly how to connect the device to your network.
The Midspan will add power to 12 ports respectively in the installation of the cabling (7/8 and 4/5). ABOUT THIS GUIDE
This user's guide provides instructions and...
Product Manual - Page 6
... version 1 MIB support for System and PoE status. Independent overload and short-circuit protection per channel Standard 19-inch rack mountable... DC power output ports. These ports are designed to carry Ethernet data only (Tx/Rx) over Ethernet compliant. Features
The DWL-P1012 features include: IEEE 802.3af Power over the standard 2-wire pairs (pins 1/2 and 3/6). Management port: One (1) 10/...
Product Manual - Page 8
... from and adequate ventilation around the Midspan. Allow enough ventilation space between the DWL-P1012 and any other surfaces. Visually inspect the power cord and see that can support at each corner of the device. When installing the Midspan on the bottom at least 6.6 lb. (3 kg) of weight.
Setup
Setup of the DWL-P1012 can be completed easily by following...
Product Manual - Page 11
... the PC power cord into the AC power connector of the DWLP1012 and the other end into the local AC power outlet.
7
IEEE 802.3af compliant Power Source Equipment will only link at 100Mbps Full Duplex when connected to the DWL-P1012. This PoE Midspan is not compatible with AC power sources 100 - 240 VAC, 50...
Product Manual - Page 12
... connected to Port 2. A description of an accidental reset the backup can be loaded through the WebUI or Web Smart Utility to factory defaults. This means that display the conditions of the DWL-P1012 and status of ports): Twelve 10/100Mbps Fast Ethernet data ports. Note: The Midspan supports PoE port priority management. When the available system...
Product Manual - Page 13
The DWL-P1012 automatically adjusts its power setting to any supply voltage in the female connector of the provided power cord into a power outlet. Plug in the range from 100 ~ 240 VAC at 50 ~ 60 Hz.
9 Rear Panel
The rear panel of the cord into this socket, and the male side of the DWL-P1012 contains...
Product Manual - Page 14
...Maximum (PWR MAX)
On : When the PoE remaining system power = 185W), the system will light green after the Midspan is powered on LED function and indication.
... DWL-P1012 include Power, CPU, PoE status and Management port status. Refer to the appropriate section below for information on to any additional PoE PD inserted. On/Off : Possible Device Failure, please contact Technical Support....
Product Manual - Page 16
...'s PoE power management configuration. Insert the DWL-P1012 Master CD in the following pages.
12 Upon completion, go to
install the utility. With the attached Web Management Utility, you can easily discover all DWLP1012 units on the network, assign them IP Addresses, change the administrative passwords and upgrade firmware. Installing the Web Management Utility
Follow these instructions to...
Product Manual - Page 19
..., the DWL-P1012 has to monitor.
Configuration Setting: In the Configuration Setting, you review and click on the event record. Note: In order to receive Trap information using the function key in the Discovery list or Monitor List and press this symbol will pop out as Error! Add Item: To add a device to the Monitor List manually...
Product Manual - Page 22
... window. Enter the DWL-P1012 IP address http://192.168.0.1 (the factory-default IP address setting) in the Monitor List of the DWLP1012 is 192.168.0.1, so the manager PC should load where the device status will be set on the same IP network. When the following dialog page appears, enter the default password "admin" and...
Product Manual - Page 25
... DWL-P1012 generates traps and sends them to read and modify the settings of events that occur on the device. These objects are messages that alert network personnel of gateways, routers, switches, and other network devices. In SNMP v.1, user authentication is an OSI Layer 7 (Application Layer) designed specifically for proper operation, monitor and detect potential problems...
Product Manual - Page 26
...: To enable or disable the SNMP function of the DWLP1012. Configure SNMP Community:
Add Group: To add an SNMP Community group, press "Add Group" button. MIBs
Management and counter information are stored by specifying the MIB Object Identifier. In addition, the DWL-P1012 also supports its own proprietary enterprise MIB as an extended Management...
Product Manual - Page 30
... a value from the drop down box corresponding to protect the DWL-P1012 and the connected device, the power limit function will disable the PoE function of the port when the power is over loaded. Power limit: This function allows one to manually set a port power current limitation to be given to the PD, to each...
Product Manual - Page 33
...DWL-P1012 rely on a port grouping mechanism that group. This allows system administrators to the 'Always Active' schedule profile.
Each port may only be modified or deleted and is assigned to control when their PoE...of one custom group.
29 Up to .
These groups are then assigned to a specific schedule profile which all members of that group adhere to 6 custom groups may only be...
D-Link DWL-P1012 Reviews
We have not received any reviews for D-Link yet.