Operation Manual
Page 3
... Amp 120V AC 60Hz 5000 RPM (No load) Yes BLADE SIZE Diameter Arbor size 10 in. 5/8 in . Failure to the tool. SAW Rip fence Miter gauge Rip Capacity Maximum Cut Depth @ 90 Maximum Cut Depth @ 45 Maximum Diameter Dado Maximum Dado Cut Width Yes Yes 24 in . Right & Left 3 in. 2-1/2 in. 6 in. (Stackable only...
... Amp 120V AC 60Hz 5000 RPM (No load) Yes BLADE SIZE Diameter Arbor size 10 in. 5/8 in . Failure to the tool. SAW Rip fence Miter gauge Rip Capacity Maximum Cut Depth @ 90 Maximum Cut Depth @ 45 Maximum Diameter Dado Maximum Dado Cut Width Yes Yes 24 in . Right & Left 3 in. 2-1/2 in. 6 in. (Stackable only...
Operation Manual
Page 12
... saw. e Maximum dado width is 1/2 in . • Do not use molding head set with this power tool or use accessories not recommended by Sears. e Do not use a dado with a diameter larger than 6 in . RECOMMENDED ACCESSORIES i_ WARNING ] Visit your Sears Hardware Department or see the Craftsman ...Power and Hand Tools Catalog to purchase recommended accessories for this power tool. [_ WARNING] To avoid the risk of personal injury: o Do not use stackable dadoes. e Only use adjustable (wobble) type dadoes or carbide tipped dado blades. Straight edge 4...
... saw. e Maximum dado width is 1/2 in . • Do not use molding head set with this power tool or use accessories not recommended by Sears. e Do not use a dado with a diameter larger than 6 in . RECOMMENDED ACCESSORIES i_ WARNING ] Visit your Sears Hardware Department or see the Craftsman ...Power and Hand Tools Catalog to purchase recommended accessories for this power tool. [_ WARNING] To avoid the risk of personal injury: o Do not use stackable dadoes. e Only use adjustable (wobble) type dadoes or carbide tipped dado blades. Straight edge 4...
Operation Manual
Page 16
...Always use a push stick. ANTI-KICKBACK PAWLS - ARBOR - HEEL - Clear plastic cover that slides in . COMPOUND CUT - A cut . Misalignment of the table saw . JAMB NUT - MITER CUT - A guide used to cut without using a rip fence, miter gauge, hold down or other proper device to use a... sap from twisting during operation, provides a way to push workpieces when performing ripping operations. The amount of the workpiece. CROSSCUT - DADO - Measures the angle the blade is mounted. A simultaneous bevel and miter cut . GUM - Performing a cut grooves in place on which ...
...Always use a push stick. ANTI-KICKBACK PAWLS - ARBOR - HEEL - Clear plastic cover that slides in . COMPOUND CUT - A cut . Misalignment of the table saw . JAMB NUT - MITER CUT - A guide used to cut without using a rip fence, miter gauge, hold down or other proper device to use a... sap from twisting during operation, provides a way to push workpieces when performing ripping operations. The amount of the workpiece. CROSSCUT - DADO - Measures the angle the blade is mounted. A simultaneous bevel and miter cut . GUM - Performing a cut grooves in place on which ...
Operation Manual
Page 17
... are, the greater the set. 17 It is removed from the table to each other. Leadinc Saw blade path Workpiece Trailing edge SAW BLADE PATH - FEATHERBOAR- When dado cutting, a dado insert plate must be cut straight. Cutting with the blade. Slightly thinner than the saw blade tips, bent outward in opposite directions to install/ remove blades...
... are, the greater the set. 17 It is removed from the table to each other. Leadinc Saw blade path Workpiece Trailing edge SAW BLADE PATH - FEATHERBOAR- When dado cutting, a dado insert plate must be cut straight. Cutting with the blade. Slightly thinner than the saw blade tips, bent outward in opposite directions to install/ remove blades...
Operation Manual
Page 42
... least one thread of the cut to install the outside blades and inside 7. Install the dado table insert making sure that the rear of round outside flange (2) before threading on this saw restricts the maximum width of the arbor sticks out past the nut. 6. It is tight...pawl assembly, riving knife assembly and table insert when you finished the dado operation. Fig. The arbor (1) on the arbor nut (3) for operating the dado is 1/2 in the dado set . 4. dado cuts. If the dado insert is not flush with the table, adjust the two bolts on this saw . in . Blade/chippers must ...
... least one thread of the cut to install the outside blades and inside 7. Install the dado table insert making sure that the rear of round outside flange (2) before threading on this saw restricts the maximum width of the arbor sticks out past the nut. 6. It is tight...pawl assembly, riving knife assembly and table insert when you finished the dado operation. Fig. The arbor (1) on the arbor nut (3) for operating the dado is 1/2 in the dado set . 4. dado cuts. If the dado insert is not flush with the table, adjust the two bolts on this saw . in . Blade/chippers must ...