Cisco WS-X4991 Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4991 manuals!
Problems with Cisco WS-X4991?
Ask a Question
Free Cisco WS-X4991 manuals!
Problems with Cisco WS-X4991?
Ask a Question
Popular Cisco WS-X4991 Manual Pages
Hardware Maintenance Manual - Page 3
... properly in this manual is not available, or, if the license fee was exported under the multinational uplift program. The information in Technical Data and Computer Software clause at Cisco's option and potentially through the Sales or Service Partner, either (i) to provide a correction or a workaround for any installation, handling, maintenance, or operating instructions supplied by...
Hardware Maintenance Manual - Page 4
... contact the place it exports the products. The above , (ii) replace the Product with the laws of the State of a warranted problem with any installation, handling, maintenance, or operating instructions supplied by Cisco, (3) has been subjected to be governed by Cisco, (2) has not been installed, operated, repaired, or maintained in accordance with any term or condition hereof.
IN...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 13
... 2-30 Jumper Settings and Functions 2-33 BRI Cable Specifications 3-6 BRI Port Pinout (RJ-45) 3-8 Creepage and Clearance Distances Based on Voltage 3-10 Four Port Serial Network Processor Module LED Indicators 4-7 Dual Serial Network Processor Module LED Indicators 4-9 Cisco 4000-M Console and Auxiliary Port Signals A-2 Cisco 4500-M and Cisco 4700 Console and Auxiliary Port Signals A-2 Dual...
Hardware Maintenance Manual - Page 15
... as an annual subscription.
To order UniverCD, contact your warranty package. Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures. About This Manual xv Audience
This publication is available both as a single CD and as an electronic or electromechanical technician.
About This...
Hardware Maintenance Manual - Page 16
...in this manual. xvi Cisco 4000 Series Hardware Installation and ...troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing...
Hardware Maintenance Manual - Page 21
... by
the Electronic Industries Association (EIA) and Telecommunications Industry Association (TIA). AWG-American Wire Gauge 2. Table 1-1
Cisco 4000 Series Physical Specifications
Description
Design Specification
Dimensions (W x D x H) 17.6" x 17.7" x 3.4" (44.7 cm x 45 cm x 8.6 cm)
Weight
24 lb (10.9 kg) (including the chassis and network processor modules)
Power
Wire Gauge for the...
Hardware Maintenance Manual - Page 37
... console and auxiliary ports support asynchronous connections.
However, you can get good results with rates and distances greater than those shown. Preparing for them, you can compensate for Installation 2-15 All serial signals are also valid for EIA/TIA-449 shown in Table 2-4. however, you understand the electrical problems that might arise and...
Hardware Maintenance Manual - Page 52
... will occasionally lose some packets. Note The multiport BRI network processor module requires that supports ISDN PRI.
Network Connection Considerations
The specifications for the BRI cable are given in Figure 2-32, provides a controller for a remote site.
2-30 Cisco 4000 Series Hardware Installation and Maintenance This interface is presented to a channel service unit (CSU).
Hardware Maintenance Manual - Page 54
... ground. These jumpers set to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance For wide-area networking, the CE1 can be configured individually. To set with one E1 interface.The CE1 provides one channelized E1 connection via a serial cable to 24 virtual channels. The CE1, shown in the G.703 specification. Jumper J2 (see...
Hardware Maintenance Manual - Page 58
... The ATM processor module for the Cisco 4000 series router uses identical duplex SC connectors for shipping damage.
If the final installation site is not ready, keep the...specific part number visible on the upper surface of the single-mode ATM products when no fiber-optic cable is connected. The router, cables, publications, and any optional equipment you encounter problems when installing...
Hardware Maintenance Manual - Page 64
...3-7 and Figure 3-8.)
The BRI network processor module supports point-to it, must be connected. If the...where the NT1 is customer owned.
3-6 Cisco 4000 Series Hardware Installation and Maintenance
nF = nanoFarad. The ...Specifications"), connect the Basic Rate Interface (BRI) port to the Integrated Services Digital Network (ISDN) through an ISDN channel service unit/digital service...
Hardware Maintenance Manual - Page 123
...router is provided. While running the system software, you isolate or rule out hardware problems encountered when installing your router. The ROM monitor can start the server in the ROM monitor:
o/r ...(>). If you set the configuration to 0x0, you must manually boot the system each time you can reset the configuration register to the ROM monitor prompt.
Entering the Cisco 4000-M ROM ...
Hardware Maintenance Manual - Page 127
...to 0x0 by setting the configuration register. The Cisco 4500-M and Cisco 4700 ROM monitor supports more features than the familiar Cisco 4000-M ROM ...set the software configuration register (bits 3, 2, 1, and 0) to zero, you reload the router. Cisco 4500-M and Cisco 4700 ROM Monitor D-1 During the 60-second window, you isolate or rule out hardware problems encountered when installing...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4991 Reviews
We have not received any reviews for Cisco yet.