Cisco WS-X4148-RJ45V= - Switching Module Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4148-RJ45V= manuals!
Problems with Cisco WS-X4148-RJ45V=?
Ask a Question
Free Cisco WS-X4148-RJ45V= manuals!
Problems with Cisco WS-X4148-RJ45V=?
Ask a Question
Popular Cisco WS-X4148-RJ45V= Manual Pages
Hardware Maintenance Manual - Page 3
... will substantially conform to the published specifications for such Software, if used in equipment provided by Cisco, (3) has been subjected to everyone are service marks, and Cisco, Cisco Systems, EtherSwitch, Kalpana, and the Cisco logo are the property of Cisco. Further, Customer agrees to use the Cisco software ("Software") in this manual is error free or that the Software is...
Hardware Maintenance Manual - Page 4
... the event of a warranted problem with the laws of the State of the software. In no event does Cisco warrant that supplied the Product to Customer or to installation of the Commercial Computer Software - CONSEQUENTIAL DAMAGES.
Cisco warrants to operate its Sales or Service Partner will supply replacement parts for the products listed in Technical Data and Computer...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 15
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures.
For software configuration information, refer to install and maintain the Cisco 4000-M, Cisco 4500-M, and the Cisco 4700. About This Manual xv To order UniverCD, contact your warranty package.
UniverCD is for rack-mounting and ...
Hardware Maintenance Manual - Page 16
... Community," describes the operating
conditions for use in the paragraph.
xvi Cisco 4000 Series Hardware Installation and Maintenance Document Conventions
• Chapter 4, "Troubleshooting the Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module...
Hardware Maintenance Manual - Page 37
...Installation 2-15 If you understand the electrical problems...Connection Considerations
Serial Connections
When setting up to 64 Kbps. Table 2-4 lists the IEEE-recommended maximum speeds...513
156
256
78
102
31
50
15
Balanced drivers allow EIA/TIA-449 signals to distance limits, beyond... interface standard in the United States, supports unbalanced circuits at distances and rates greater...
Hardware Maintenance Manual - Page 43
...Specifications." Note that the cables for the two versions of serial modules: both DTE and DCE versions of the dte-invert-timing command must also be configured for Installation 2-21
An error message will be manually ...Note Serial ports configured as DTE in Figure 2-21. To set , or if the cable is DCE and the clock rate is set the jumpers for NRZI, move the jumpers to operate as shown...
Hardware Maintenance Manual - Page 54
... Figure 2-34, provides a controller for E1
CE1 Jumper Settings The jumpers on the CE1 module set with one E1 interface.The CE1 provides one channelized E1 connection via a serial cable to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance Jumper J2 (see G.703 / Section 6.3 (CCITT specification) • Jitter attenuation starting at 6 hertz (Hz...
Hardware Maintenance Manual - Page 55
...either BNC, DB-15, Twinax, or RJ-45 connectors on the network end. For the CE1 module, four serial cables are available from Cisco Systems. All three have DB-15 connectors... and for Installation 2-33 J1, J3, J4, 1 and 2
J5, J71
2 and 3
Sets cable impedance to 120-ohm Sets cable impedance to the same impedance.
All of these jumpers must be configured by trained service personnel only....
Hardware Maintenance Manual - Page 56
... 155 Mbps in a back-to connect the ATM processor module with RJ-45 Connector)
H2422
ATM Connections
The ATM processor module for the ATM NPM.
2-34 Cisco 4000 Series Hardware Installation and Maintenance If the middle slot is not occupied by the specific physical layer). The ATM interface cable is determined by the PLIM...
Hardware Maintenance Manual - Page 64
... owned.
3-6 Cisco 4000 Series Hardware Installation and Maintenance Making BRI Connections
Using the appropriate cable (see Figure 3-7 and Figure 3-8) supports eight BRI ports. nF = nanoFarad. Each BRI port is an ISDN channel service unit/digital service unit (CSU/DSU). The BRI module does not support a point-to shut down. Table 3-1
BRI Cable Specifications
Parameter Resistance...
Hardware Maintenance Manual - Page 66
...Switched Digital Networks (ISDN), each at the S reference point. Table 3-2
BRI Port Pinout (RJ-45)
8 Pin1
TE2
NT3
Polarity
3
Transmit
Receive
+
4
Receive
Transmit
+
5
Receive
... card assembly for isolating hardware problems on the corresponding port. TE refers to -point mode only.
3-8 Cisco 4000 Series Hardware Installation and Maintenance
Making Network Connections
BRI...
Hardware Maintenance Manual - Page 123
... register. If you set the configuration to the ROM monitor prompt. Entering the Cisco 4000-M ROM Monitor Program
The ROM monitor diagnostics help you reboot the router. The ROM monitor can break to 0x0, you must manually boot the system each time you isolate or rule out hardware problems encountered when installing your router. Timesaver...
Hardware Maintenance Manual - Page 127
Cisco 4500-M and Cisco 4700 ROM Monitor D-1 A summary of the ROM monitor diagnostic tests and command options is rebooted with the reload command. If you set the configuration to 0x0, you will have to manually boot the system from the console each time you isolate or rule out hardware problems encountered when installing your router. During the 60...
Hardware Maintenance Manual - Page 141
...P
packing list 2-36 ...Ethernet LED 4-5 port locations 2-7 software configuration, serial 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem...
Cisco WS-X4148-RJ45V= Reviews
We have not received any reviews for Cisco yet.