Cisco WS-C6506 Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco WS-C6506 manuals!
Problems with Cisco WS-C6506?
Ask a Question
Free Cisco WS-C6506 manuals!
Problems with Cisco WS-C6506?
Ask a Question
Cisco WS-C6506 Videos
Popular Cisco WS-C6506 Manual Pages
Installation Guide - Page 49
... or two power supplies. These fan tray models are not field replaceable. WS-C6506-E-FAN-564 CFM
Note You must replace the fan tray.
• Fan tray STATUS LED - The 2500 W power supply can also be powered from either redundant or non-redundant mode.
• All Catalyst 6500 series AC-input power supplies require single-phase source AC. The individual fans are
supported:
- WS-CAC-2500W...
Installation Guide - Page 59
... ratings. OL-5781-04
Catalyst 6500 Series Switches Installation Guide
1-35 WS-C6509-E-FAN-846 CFM
Note You must replace the fan tray.
• Fan tray STATUS LED - The 2500 W power supply can be configured in the chassis to power the high-speed fan tray. Red-One or more individual fans have failed. - The following models are
supported:
-
Chapter 1 Product Overview
Catalyst 6509...
Installation Guide - Page 318
... these subsystems:
• Power supply-Includes the power supplies and power supply fans.
• Fan assembly-The chassis fan assembly should see the FAN LED turn green and hear the fan assembly operating. Also, refer to a specific system component. Solving Problems at the System Component Level
The key to success when troubleshooting the system is partially installed in the backplane...
Supervisor Guide - Page 16
...
• The uplink ports are fully functional on the minimum software release versions required to support the supervisor engines in slot 1 or slot 2. Additional information on the Catalyst 6503 switch chassis including data sheets and chassis installation is located at:
http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html
Catalyst 6503-E
The Catalyst 6503...
Supervisor Guide - Page 19
... for modules. Identical supervisor engine memory configurations are recommended but are supported. The 6-slot (numbered from (1) top to your software release notes for any restrictions on the Catalyst 6506 switch chassis including data sheets and chassis installation is located at:
http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html
Catalyst 6506-E
The...
Software Guide - Page 399
...set of service (QoS) feature set that is supported on your switch is determined by multiple features, Cisco IOS software examines it multiple times. Most Cisco IOS features are associated with multiple features for specific... Series Switch Software Configuration Guide-Release 8.7
15-3 see Chapter 52, "Configuring QoS." However, some features use ACLs for more information. One Cisco IOS...
Software Guide - Page 609
... ports:
Console> (enable) clear port ethernet-oam statistics
OL-8978-04
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
20-33 The error-block action then automatically changes the port to monitor the link status flag. Does not support errordisable and error-block.
If you specify the dying-gasp keyword, the errordisable option is warning...
Software Guide - Page 741
...the running the c6msfc2-jsv-mz.9E image. OL-8978-04
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
23-49 Getting Out of Single Router Mode
Note If you...is now disabled on the designated router and nondesignated router.
Manual-Mode MSFC Redundancy
Note Manual-mode MSFC redundancy will be supported until December 2002 due to reload the designated router and ...
Software Guide - Page 744
...if the active MSFC reboots without problems. If it does not, you ... switch console command.
23-52
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
OL-8978-04 From the ROMMON...Setting the MSFC Configuration Register
For manual-mode MSFC redundancy, set the configuration registers as follows:
Step 1 Step 2
From Cisco IOS configuration mode on bootflash and that you do not set...
Software Guide - Page 973
... kerberos srvtab entry host/niners.cisco.com@CISCO.COM 0 kerberos> (enable)
Enabling Credentials Forwarding
A user that no Kerberos credentials are mandatory for users to authenticate to other services on the network with the Kerberized clients. As an additional layer of authentication for a password. Command set kerberos credentials forward
set kerberos clients mandatory
This example shows...
Software Guide - Page 984
...Console> (enable) show authorization
Telnet: ------- Console:
--------
If the service-type is set for anything other than 6-administrative (for the user to Admistrative (that... is, a value of 6) in the RADIUS server to disable RADIUS authorization.
39-50
Catalyst 6500 Series Switch Software Configuration Guide...
Software Guide - Page 1051
...Task
Command
Initialize the MAC authentication bypass state for a port:
Console> (enable) set port mac-auth-bypass 3/1 enable MAC-Auth-Bypass successfully enabled on 3/1. Chapter 41 ...00-01 on port 3/1 using Mac-Auth-Bypass. OL-8978-04
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
41-7 Console> (enable)
Reauthenticating the MAC Address for a Port
To... the ports manually.
Software Guide - Page 1220
...> (enable)
Configuring Multicast Groups
To configure a multicast group manually, perform this task in privileged mode:
Note With software release 7.1(1) and later releases, the maximum number of Entries = 4 Console> (enable)
51-28
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
OL-8978-04
Console> (enable) set multicast router 2/2
Port 2/2 added to multicast router...
Software Guide - Page 1417
... Service (COPS) considerations
COPS directly affects how the QoS parameters are supported ...(trust-cos, trust-ipprec, trust-dscp), but you should get its QoS configuration information from the local configuration or through a COPS server. Trusted boundary configuration
- See Figure 55-6 to the Catalyst 6500 Series System Message Guide for the trusted boundary to notify you must set...
Software Guide - Page 1441
... service.
Network Address Translation (NAT) does not work with Supervisor Engine 2, refer to this URL:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/ wccp.html
OL-8978-04
Catalyst 6500 Series Switch Software Configuration Guide-Release 8.7
56-3 WCCP-redirected packets that is supported only with WCCP configured. This problem...
Cisco WS-C6506 Reviews
Do you have an experience with the Cisco WS-C6506 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!