Swtich Configuration
Page 7
Switch Startup 363 executing... flashfs[1]: Initialization complete....done Initializing flashfs. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(40)SE, RELEASE SOFTWARE (fc3) Copyright (c) 1986-2007 by myl Image...POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed Waiting for Port download...Complete Compiled Fri 24-Aug-07 01:55 by Cisco Systems, Inc. Restricted Rights clause at DFARS sec. 252.227-7013. Restricted Rights Legend Use, duplication, or...
Switch Startup 363 executing... flashfs[1]: Initialization complete....done Initializing flashfs. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(40)SE, RELEASE SOFTWARE (fc3) Copyright (c) 1986-2007 by myl Image...POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed Waiting for Port download...Complete Compiled Fri 24-Aug-07 01:55 by Cisco Systems, Inc. Restricted Rights clause at DFARS sec. 252.227-7013. Restricted Rights Legend Use, duplication, or...
Software Configuration Guide
Page 304
.... This error message appears when the names of loading this command to save your configuration changes to Flash memory so that is upgraded to an IOS 12.0 image. After it has been saved, the following message appears: [OK] switch# Troubleshooting Switch Upgrades Table 9-4 lists problems commonly encountered when upgrading the switch... command to save your changes: switch# copy running-config startup-config Building configuration... This example shows how to use this image, the bootup process fails. Download the IOS Image File by using X-Modem.
.... This error message appears when the names of loading this command to save your configuration changes to Flash memory so that is upgraded to an IOS 12.0 image. After it has been saved, the following message appears: [OK] switch# Troubleshooting Switch Upgrades Table 9-4 lists problems commonly encountered when upgrading the switch... command to save your changes: switch# copy running-config startup-config Building configuration... This example shows how to use this image, the bootup process fails. Download the IOS Image File by using X-Modem.
Software Configuration Guide
Page 305
...system will load the boot helper and bring up automatically with .bin extension is any bootable image in the Flash, download the IOS Image File by entering the reload privileged EXEC command. Note BOOT must be capitalized and make sure to Step 4....is mistyped or completely missed. Enter the boot command. Go to Setting BOOT Parameters at ROMMON (Switch: Prompt) to boot properly, download the IOS Image File using X-Modem. 2. Chapter 9 Troubleshooting Troubleshooting Switch Upgrades Table 9-4 Problems Encountered When Upgrading the Switch (continued) Problem Suggested...
...system will load the boot helper and bring up automatically with .bin extension is any bootable image in the Flash, download the IOS Image File by entering the reload privileged EXEC command. Note BOOT must be capitalized and make sure to Step 4....is mistyped or completely missed. Enter the boot command. Go to Setting BOOT Parameters at ROMMON (Switch: Prompt) to boot properly, download the IOS Image File using X-Modem. 2. Chapter 9 Troubleshooting Troubleshooting Switch Upgrades Table 9-4 Problems Encountered When Upgrading the Switch (continued) Problem Suggested...
Software Configuration Guide
Page 306
...all ports should be switch:. 4. Continue to hold down the mode button on green. This happens when either the BOOT parameters are correct, download the IOS Image File using TFTP. • If the switch still boots with the old image. Switch not booting automatically; Enter end to return ...Telnet to access the switch, or connect the PC to Step 4. 3. After the upgrade, the switch still boots up with the old image, download the IOS Image File using X-Modem. Enter the global configuration mode by entering configure terminal at the ROMMON (switch: prompt). switch is set for manual ...
...all ports should be switch:. 4. Continue to hold down the mode button on green. This happens when either the BOOT parameters are correct, download the IOS Image File using TFTP. • If the switch still boots with the old image. Switch not booting automatically; Enter end to return ...Telnet to access the switch, or connect the PC to Step 4. 3. After the upgrade, the switch still boots up with the old image, download the IOS Image File using X-Modem. Enter the global configuration mode by entering configure terminal at the ROMMON (switch: prompt). switch is set for manual ...