Cisco SRW208MP Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SRW208MP manuals!
Problems with Cisco SRW208MP?
Ask a Question
Free Cisco SRW208MP manuals!
Problems with Cisco SRW208MP?
Ask a Question
Popular Cisco SRW208MP Manual Pages
User Guide - Page 7
...port 10/100 Ethernet Switch with data traffic allowing them each to be prioritized above others using MAC-based filtering. Individual users or applications can be setup. Incoming traffic can be policed and outgoing traffic can provide maximum output power per PoE port up to expand your network securely. The SRW208P and SRW208MP support Automatic Load Sensing -
If a specific model...
User Guide - Page 25
... name. System Location This field is used .
8-Port 10/100 Ethernet Switch with a Static or Dynamic IP address (configurable from Setup > Network Settings tab). Host Name Enter the DHCP Host Name here. Subnet Mask Enter the subnet mask of power the device can supply. Model Name The model name of the Switch. Firmware Version The current software version is displayed. System...
User Guide - Page 60
...This is the port to copy all error reporting. Target Port Defines the port from which identifies the source application generating the message. Port mirroring also enables switch performance monitoring. Short Cable indicates that are assigned a severity code, and include a message mnemonic, which traffic is mirrored. If a Debug error occurs, contact Customer Tech Support. This is no...
User Guide - Page 74
....
Appendix D
Specifications
Model Ports
Cabling Type
LEDs
Performance Switching Capacity Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN
HOL Blocking Management Web User Interface
SNMP
SRW208L 8 RJ-45 Connectors for 10BASE-T and 100BASE-TX, 1 miniGBIC/SFP port, 1 LC type connector for 100LX SMF port at 1310nm Console Port Auto MDI/MDI-X Autonegotiate/Manual Setting UTP CAT...
Hardware Installation Guide - Page 4
...P T E R
Intended Uses 2-8 If AC Power Supplies Are Installed 2-8 If DC Power Supplies Are Installed 2-9 Temperature and Ventilation 2-10
Installing the Content Delivery Engines 3-1 Server Types 3-1 Tools and Parts Required 3-2 Unpacking the Box 3-2 Verifying Contents 3-3 Inspecting for Damage 3-3 Installing the CDEs 3-3 Reviewing Rack Installation Safety Guidelines 3-3 Preparing the CDEs for Rack...
Hardware Installation Guide - Page 17
...SE) • Service Router (SR)
OL-13478-03
Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
1-1 1 C H A P T E R
Overview of the Content Delivery Engines
This chapter provides an overview of CDAs that can be configured with Cisco CDS software within your existing network, your network must support Cisco IOS software. Each device mode defines the set of the Content...
Hardware Installation Guide - Page 35
... handles on DC power terminals. Install only in service. Statement 1045
Warning Installation of cooling air through a device that might disrupt other equipment; Always replace cover when terminals are not in accordance with local and national electrical codes. Do not operate the unit without the covers installed. these types of handles are an integral part of the safety...
Hardware Installation Guide - Page 43
..., cards, power supplies, and cables for any damage resulting from shipping, contact your local freight carrier for the location of your nearest service center.
If any items are present and in good condition. Keep a record of the parts and serial numbers. Installing the CDEs
Installing the CDS consists of the following tasks: • Reviewing Rack Installation Safety Guidelines...
Hardware Installation Guide - Page 84
... hot-swappable1
Fan Assembly Operating ...Installation Guide
C-2
OL-13478-03 Network PVR is fully supported 8 Gigabytes RAM
Processor Protocols
Two Dual Xeon @ 3.2 GHz (or above) IP, SNMP, FTP, Gigabit Ethernet, SSH, FSI, DSM-CC, LSCP, RTSP
Controllers
Marvell Serial-ATA
Operating System Operating System Disk
Red Hat 7.3 distribution supporting Linux kernel 2.4.19 Two 60- The power supplies...
Hardware Installation Guide - Page 85
... (50/125 mm), 902 ft (275 m) maximum (62.5/125 mm)
Performance Monitoring Power
Integrate with both the Tandberg and C-COR back office suite 625 W (110 and 220 VAC or -48 VDC) redundant, hot-swappable1
Fan Assembly
Redundant with Serverworks Chipset
Specifications
CDE200 (IBM)
CDE300
Dimensions (H x W x D)
3.50 (2U) × 17.50 × 27.48...
Administration Guide - Page 31
...:
• Upgrade the firmware or boot code, or replace a second language, as described in Upgrade/Backup Firmware/Language section.
• Save configuration files on the switch to a location on another device as described in the Downloading or Backing-up a Configuration or Log
• Viewing Configuration Files Properties
Cisco Small Business 200 Series Smart Switch Administration Guide
32...
Administration Guide - Page 33
...replaced with a new version of the backup file. Firmware Image-Select this to upgrade the firmware image.
- Managing System Files
Upgrade/Backup Firmware/Language
4
Select one link local address is used). If a link local address exists on another device. The following file types can be upgraded:
- Cisco Small Business 200 Series Smart Switch Administration Guide... networks.
•...
Administration Guide - Page 104
... channel (LAG).
Cisco Small Business 200 Series Smart Switch Administration Guide
105 The group of ports assigned to dynamic LAG are standby ports ready to replace any failing active member ports. Port Management
Configuring Link Aggregation
9
• Link Aggregation Overview
• Static and Dynamic LAG Workflow
• Defining LAG Management
• Configuring LAG Settings
•...
Administration Guide - Page 248
... by default on it. There are bound to enable viewing CPU resource utilization information. Cisco Small Business 200 Series Smart Switch Administration Guide
249 Configuring Security
Denial of Service Prevention > Security Suite Settings. SCT can be disabled. Denial of Service Prevention > Security Suite Settings page (Details button). STEP 2 Click Details beside CPU Utilization to...
Administration Guide - Page 274
...-Egress traffic from the lower queues is updated.
STEP 4 Select the Port or LAG interface.
The Interface Settings page is mapped to enable or disable QoS State for each port of Service > General > Interface Settings. Configuring QoS Queues
The switch supports four queues for this interface. General
20
Interface QoS Settings
The Interface Settings page enables configuring QoS on the...
Cisco SRW208MP Reviews
We have not received any reviews for Cisco yet.