Cisco MC3810-V - Concentrator - External Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco MC3810-V manuals!
Problems with Cisco MC3810-V?
Ask a Question
Free Cisco MC3810-V manuals!
Problems with Cisco MC3810-V?
Ask a Question
Popular Cisco MC3810-V Manual Pages
User Guide - Page 1
... for static, manually provisioned permanent virtual circuits (PVCs). ATM SVC service operates much like X.25 SVC service, although ATM allows much higher throughput. The ATM signaling software provides a method of the voice features that are ideal for networks that the Cisco MC3810 supports for PVCs and for the Cisco MC3810 multiservice access concentrator. In UNI, the router serves as...
User Guide - Page 2
...-Network Interface
(UNI) signaling specification, version 4.0, simultaneously supporting permanent virtual circuits (PVCs) and SVCs.
• Network Service Access Point (NSAP) addressing for private networks • Interim Local Management Interface (ILMI) • 24 simultaneous voice calls per Cisco MC3810 system • Support for tandem switching
Note The Cisco MC3810, in addition to the...
User Guide - Page 3
... with multiple hops. Improves voice quality because there is more information about the commands and configuration steps required for example, IP traffic is compressed, decompressed, and compressed again.
- Benefits
Benefits
The Cisco MC3810 multiservice access concentrator formerly supported only non-dial permanent virtual circuits (PVCs) for ATM SVC service. • Interface requirements...
User Guide - Page 4
... Specification V3.1
(1994), including support for ATM, consult the following Cisco IOS Release 12.0 documents:
• Wide-Area Networking Configuration Guide • Wide-Area Networking Command Reference
For information about Cisco IOS configuration for the following Cisco documents:
• Cisco MC3810 Multiservice Access Concentrator Software Configuration Guide • Cisco MC3810...
User Guide - Page 5
.... Activate the controller.
For more information, refer to the Cisco MC3810 Multiservice Access Concentrator Software Configuration Guide and to T1 controller 0;
Configuring Network Clocks and Controller Settings
Configuration Tasks
Perform the following tasks to T1 controller 1. then the clock source is set up voice POTS and ATM dial peers. ATM traffic is automatic for...
User Guide - Page 6
.... Router# show network-clocks
Priority 1 clock source(inactive config): T1 0 Priority 1 clock source(active config) : T1 0
Step 2
Enter the privileged EXEC show controllers t1 or show controllers e1 command to see the Cisco IOS Release 12.0 network protocol configuration and command reference guides. Applique type is Channelized T1 Cablelength is automatically set . The line coding...
User Guide - Page 7
... Model TEB HWVersion 3.80 Framing is CRC4, Line Code is HDB3, Clock Source is specified. Assign the IP address and subnet mask to carry signaling for ATM 0-the only ATM interface that supports voice over ATM Switched Virtual Circuits on the Cisco MC3810 7 For additional information, see Cisco MC3810 Multiservice Access Concentrator Software Configuration Guide and Cisco MC3810 Multiservice...
User Guide - Page 11
... errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 367264676 packets output, 3261882795 bytes, 0 underruns 0 output errors,...not set up
Hardware is PQUICC Atom1 Internet address is set Keepalive not supported ...Voice over ATM Switched Virtual Circuits on the Cisco MC3810 11 The following example:
Router# show interface atm 0 ATM0 is up, line protocol is up to allow SVC management:
Router...
User Guide - Page 12
... (MFT) is installed, the slot number is 1. Voice dial peers are persistent and exist until they are specifically removed with the typical fax rate of 9.600 bps. Therefore, you can either change the fax rate. Therefore, you can either change the codec or change the codec (see Step 6.
4
Router(config-voiceport) exit
5
Router(config)# dial...
User Guide - Page 14
...-through is disabled Percent Break of signaling protocol errors are 0 Impedance is set to 600r Ohm
Voice card specific Info Follows: Signal Type is immediate Operation Type is 2-wire E&M Type is 1 Dial Type is dtmf In Seizure is active Out Seizure is active Digit Duration Timing is set to 100 ms InterDigit Duration Timing is...
User Guide - Page 16
..., which are set to no form of the busyout forced command restores the voice port.
16 Cisco IOS Release 12.0(7)T For general information about troubleshooting and voice QoS, see if any additional steps should be put into a busyout state. Step 2
On both sides of the Cisco MC3810 multiservice access concentrators on both Cisco MC3810 multiservice access concentrators, make sure...
User Guide - Page 17
... troubleshooting steps before taking this route. For example, if there are not set to make changes, see the Cisco IOS Release 12.0 documents, Wide-Area Networking Configuration Guide and Wide-Area Networking Command Reference. If you may wish to -back Cisco MC3810 multiservice access concentrators and one is in a state of readiness, as shown in Cisco MC3810 Multiservice Access Concentrator...
User Guide - Page 20
..., which are for ATM service. hostname MC3810A ! appletalk routing ipx routing 1111.0045.0002
The following commands show how to configure the ATM interface and set up PVCs to specify all of two Cisco MC3810 multiservice access concentrators that you can also specify the voice NSAP address by using ATM SVCs for Voice
Cisco MC3810
ATM
Cisco MC3810
Initially, the network clocks...
User Guide - Page 25
atm voice aesa
Related Command
Command show atm video-voice address
Description Allows you to review the address assigned to an ATM interface. Voice over ATM Switched Virtual Circuits on the Cisco MC3810 25
User Guide - Page 29
... to insure that ATM management is set up and operational to see information about the status of ILMI management. ATM interface NSAP address.
Example
On a Cisco MC3810, the following example shows how to manage SVC communications.
show atm video-voice address
show atm video-voice address
To display the network service access point (NSAP) address for the...
Cisco MC3810-V Reviews
We have not received any reviews for Cisco yet.