Cisco AS5200 - Universal Access Server Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco AS5200 manuals!
Problems with Cisco AS5200?
Ask a Question
Free Cisco AS5200 manuals!
Problems with Cisco AS5200?
Ask a Question
Popular Cisco AS5200 Manual Pages
Installation Guide - Page 1
Quick Start Guide
CISCO AS5200 UNIVERSAL ACCESS SERVER INSTALL AND CONFIGURE
1 TOOLS AND EQUIPMENT
2 INSTALL THE UNIVERSAL ACCESS SERVER
3 CONFIGURE THE UNIVERSAL ACCESS SERVER
Installation Guide - Page 3
...; 19-inch telco rack-mount brackets (P/N 700-01928-01)
• Quick Start Guide (this document)
• Cisco AS5200 Universal Access Server Hardware Installation Guide
• Cisco AS5200 Universal Access Server Software Configuration Guide
Ordering Information
To place an order, contact Cisco Customer Service at 408 526-4000 or 800 553-6387.
• Regulatory Compliance and Safety...
Installation Guide - Page 4
... additional screws to the chassis, but not for Desktop Use."
2 Install the Universal Access Server
Front panel forward
Rear panel forward
Rear panel forward, center-mount telco
2
H10335
Prepare the Chassis for Rack-Mounting
You can install the chassis in a rack.
Screws are included. Step 1 Attach the brackets using one of the three
methods shown above. Step...
Installation Guide - Page 5
...the dotted circles at each corner of the chassis bottom. Step 4 Place the access server right-side up on a
flat , smooth, secure surface.
2 Install the Universal Access Server (continued)
3
Universal access server chassis bottom
Prepare the Chassis for Desktop Use
Attach the rubber feet before installing the chassis on the black adhesive strip that
weighs more than 10 lb (4.5 kg...
Installation Guide - Page 7
... are not included. Step 2 Connect the other end of the access server. Step 1
Connect your Ethernet AUI cable to the port labeled AUI on the rear panel of the Ethernet
cable to a hub.
2 Install the Universal Access Server (continued)
Ethernet AUI port (DB-15)
H10342
Universal access server Ethernet hub
5
Ethernet AUI cable
Connect the Ethernet Port for Thick...
Installation Guide - Page 9
... networks terminating units are not included. 2 Install the Universal Access Server (continued)
H10338
E1/PRI port 1 (DB-15) E1/PRI card E1/PRI port 0 (DB-15)
E1 cable
Universal access server
E1 networks terminating unit
7
DB-15, Twinax, RJ-45, or
BNC connector
Connect the Dual E1/PRI Card for WAN Access
You will need two E1 cables...
Installation Guide - Page 10
... cable to a CSU/DSU or other DCE (such as a modem).
Note: CSU/DSUs and serial transition cables are not included. 2 Install the Universal Access Server (continued)
H10339
Synchronous serial port (DB-60)
Serial transition cable
Universal access server
8
EIA/TIA-232, EIA/TIA-449, V.35, X.21, or EIA-530 connector
Connect the Synchronous Serial Port for WAN...
Installation Guide - Page 11
... steps:
Step 1
Connect one of the RJ-45-to-RJ-45 rollover cable to the adapter.
2 Install the Universal Access Server (continued)
H10340
RJ-45-to-RJ-45 rollover cable
Universal access server
Console port (RJ-45) (labeled CONSOLE)
PC (laptop)
9
Connect to a Console for 9600 baud, 8 data bits, no parity, and 1 stop bit. These cables and adapters are included...
Installation Guide - Page 12
... cable and adapter are included.
If you will not be using a modem to configure the access server remotely, skip this procedure and go to the next page.
The modem is not included. 2 Install the Universal Access Server (continued)
H10341
RJ-45-to-RJ-45 rollover cable
Universal access server Auxiliary port (RJ-45)
(labeled AUX)
Modem
10
RJ...
Installation Guide - Page 13
... to enter the initial configuration dialog? [yes]:
While you are waiting for
the startup messages to stop. 2 Install the Universal Access Server (continued)
H10343
To power outlet
Universal access server Power switch
11
Connect a Power Cable and Power on the Universal Access Server
Step 1
Connect one end of the power cord to the power connector on your console screen. Step 2 Connect the...
Installation Guide - Page 14
... protocol settings including default and user defined (static) routes
Using Other Options
For all other configurations, use the Cisco IOS Release setup script or the command line interface. Refer to select. Use the information on using the command line interface to configure your Cisco AS5200 universal access server. It provides easy, step-by-step instructions for...
Installation Guide - Page 15
... prompts you through configuring and testing the universal access server. 3 Configure the Universal Access Server (continued)
12 Timesaver Use Appendix A to help you gather the appropriate information before you begin to
9 3 configure the access server using the setup script. 6
Install and Run Cisco Fast Step
1 Insert the Cisco Fast Step CD-ROM (attached to start
the Fast...
Installation Guide - Page 16
...want the password for configurating your universal access server. If ...Use this information from other Cisco devices on your network)?
2
What do you want the encrypted enable secret password
to be?
3
What do you want the nonencrypted enable password to
be ?
Item Ask Your Network Administrator
Enter the Information in This Column
1
What do you want to name the access server...
Installation Guide - Page 17
... Information (continued)
Item 6
7 8 9 10 11 12 13 14
Ask Your Network Administrator If you are configuring asynchronous interfaces, what is your telco line coding type? How many bits are in the subnet mask? What is the IP address for the IP local pool?
Installation Guide - Page 20
... countries. Addresses, phone numbers, and fax numbers are service marks; and certain other trademarks mentioned in this document are the property of their respective owners. (9902b R)
Printed in the USA on the
Cisco Connection Online Web site at http://www.cisco.com/offices. DOC-AS5200-QSG= 78-4311-03
Parc Evolic, Batiment L1/L2...
Cisco AS5200 Reviews
We have not received any reviews for Cisco yet.