Cisco 12416 Support and Manuals
Get Help and Manuals for this Cisco item
Most Recent Cisco 12416 Questions
Shipping/packing Materials For A 12416 Cisco Router Chassis
We need to remove a 12416 Router chassis and ship to another site how do we go about ordering the or...
We need to remove a 12416 Router chassis and ship to another site how do we go about ordering the or...
(Posted by paulgarcia 10 years ago)
Popular Cisco 12416 Manual Pages
Chassis Replacement Instructions - Page 1
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
Cisco Product Number: GSR16-CHASSIS= Document Order Number: DOC-7816082=
Introduction
This publication describes how to remove and install the Cisco 12016, Cisco 12416, and Cisco 12816 Router chassis. Contents
The following sections are included in this publication: • Chassis Overview, page 2 • ...
Chassis Replacement Instructions - Page 2
...See Figure 1.) Because the router can be configured with either an AC- Figure 1
Cisco 12016, Cisco 12416, and Cisco 12816 Router (Front View, AC-Input Power Subsystem Shown)
Power shelf and power supplies
Upper blower module
Upper cable management
bracket RP
Alarm card Upper card cage
Air filter door
Switch fabric card cage
(behind filter door)
Alarm card Lower card cage
Lower cable management...
Chassis Replacement Instructions - Page 3
... right to accept specific card types. If the router is an inverted, or head-down orientation.
blank filler line cards are the clock and scheduler cards (CSCs) and the switch fabric cards (SFCs). The lower card cage is not equipped with four DC-input power entry modules (PEMs).
78-16082-01
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
3 The two far...
Chassis Replacement Instructions - Page 4
...; Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
4
78-16082-01
An optional two-level power shelf is presented in the following guidelines are for your safety and to operate temporarily on the two remaining power supplies. In the full redundant power configuration, modules A1 and B1 provide redundant power for system load zone 2 (the switch fabric card...
Chassis Replacement Instructions - Page 6
...
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
6
78-16082-01 These screws prevent accidental removal, provide proper grounding for Installation
• Always place a card component-side-up on an antistatic surface, in an antistatic card rack, or in the backplane, then tighten both captive screws on the faceplate of the slot.
• Handle line cards...
Chassis Replacement Instructions - Page 7
...• Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide • Regulatory Compliance and Safety Information for the Cisco 12000 Series Internet Router
Removing and Installing the Chassis
The router chassis is an integrated, sheet-metal assembly that includes the upper blower module bay, the upper card cage, the switch fabric card cage and air filter door, the...
Chassis Replacement Instructions - Page 9
... that the LED labeled PWR OK on each power supply is off. Turn off . Verify that the power fan
in each blower module is off all circuit breakers for the source power lines connected to remove and the install the chassis.
78-16082-01
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
9 Removing and Installing the Chassis
Figure 3
SFC
12 ALARM
CSC...
Chassis Replacement Instructions - Page 10
...-management troughs must disconnect any cable that is attached to the installation and configuration note for your specific line card for detailed procedures. After disconnecting the cables, remove them from the chassis and place them safely aside. Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
10
78-16082-01 After disconnecting the cables, remove them...
Chassis Replacement Instructions - Page 12
..., Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide for detailed procedures.
Remove the bonding and grounding cable and set it in a later procedure. Remove the cards from all three card cages and then install them into the replacement chassis.
• For the RP, refer to the RP installation and configuration note for detailed procedures.
• For line cards, refer...
Chassis Replacement Instructions - Page 13
... Figure 7.)
78-16082-01
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
13 With one person in the...install the four chassis anchor clips through the slots in the bottom of the rack-mounting platform in front of the chassis to support and guide...is still supported by the rack-mounting platform installed in installing the replacement chassis.
Set the ...
Chassis Replacement Instructions - Page 20
... fabric card cage on the back of the chassis. SFC
12 ALARM
CSC 10
FAIL ENABLED 0
Q OC-3/STM-POS
6DS3-SMB P/H/F
Figure 14 Router Front ...Air filter door
28022
Figure 15 Router Top Bonding and Grounding Receptacles
29183
Supplemental bonding and grounding receptacle
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
20
78-16082-01
Removing and Installing...
Chassis Replacement Instructions - Page 21
... through the access holes in the cable lug and chassis, then install the locking washers and nuts.
Reconnect the cables to the Cisco 12016, Cisco 12416, and Cisco 12816 Router Clock and Scheduler, Switch Fabric, and Alarm Card Replacement Instructions for detailed procedures. Refer to the line card installation and configuration note for the second bonding and grounding connection, if...
Chassis Replacement Instructions - Page 22
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
22
78-16082-01 Refer to ensure proper air flow through the chassis and proper compliance with electromagnetic compatibility (EMC) regulations.
• Power modules are fully inserted in the "Checking Router Operation" section on page 22, install the chassis front covers. Also by default, the software ...
Chassis Replacement Instructions - Page 23
... DC power source supplying power within the required range, and the circuit breaker on the faceplate of the scissor-jack platform (two brackets on each side).
78-16082-01
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
23 the LED labeled FAIL should be on; If you should immediately hear them operating. you are redundantly powered by the other power module...
Chassis Replacement Instructions - Page 30
...-hour-a-day, award-winning technical support services, online and over the phone.
Obtaining Technical Assistance
For all the tools on the Cisco TAC website requires a Cisco.com user ID and password.
The Cisco TAC website is located at this URL: http://tools.cisco.com/RPF/register/register.do
Cisco 12016, Cisco 12416, and Cisco 12816 Router Chassis Replacement Instructions
30
78-16082-01...
Cisco 12416 Reviews
We have not received any reviews for Cisco yet.