Brother International LX3817 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International LX3817 manuals!
Problems with Brother International LX3817?
Ask a Question
Free Brother International LX3817 manuals!
Problems with Brother International LX3817?
Ask a Question
Brother International LX3817 Videos
Review of Brother lx3817: trouble shooting when needle is misaligned and hits metal on bottom
Duration: 14:11
Total Views: 14,578
Duration: 14:11
Total Views: 14,578
Brother LX3817- How to Thread the Needle
Duration: 3:59
Total Views: 127,810
Duration: 3:59
Total Views: 127,810
Unboxing Brother LX3817 Sewing Machine | Quick Sewing Tips #4 | LTS Academy
Duration: 7:24
Total Views: 18,009
Duration: 7:24
Total Views: 18,009
Brother LX3817 FACTORY REMANUFACTURED SEWING MACHINE UNBOXING
Duration: 3:27
Total Views: 707
Duration: 3:27
Total Views: 707
Popular Brother International LX3817 Manual Pages
Operation Manual - Page 5
... 5
Optional accessories 5
THE MAIN PARTS 6
Flat bed attachment 6
USING YOUR SEWING MACHINE 7
Connecting plugs 7 Main power and sewing light switch 8 Foot controller 8 Checking the needle 8 Replacing the needle 8 Changing the presser foot 10
THE CONTROLS 11
Pattern selection dial 11 Patterns and stitch names 11 Reverse sewing lever 12
THREADING THE MACHINE 13
Winding the bobbin 13...
Operation Manual - Page 6
...No.
Part Code Americas Others 3-piece set: XE5328-001 2-piece set (90/14 needle)
6 Screwdriver
7 Foot controller
Note
● The included accessories vary depending on the model you purchased, the following are available as optional accessories to help you easily perform most sewing tasks.
1.
2.
3.
4.
5.
No.
Depending on the machine model. KNOWING YOUR SEWING MACHINE...
Operation Manual - Page 9
....
● Never sew with product code 888-X64/X74/ X77/X87. When you press the foot controller down the foot controller. CAUTION
● Do not allow pieces of cloth and dust to the machine.
■ Checking the needle correctly
Put the flat side of any bent needles safely.
1
2
1 Parallel space 2 Level surface (bobbin cover, glass, etc...
Operation Manual - Page 12
...
11
KNOWING YOUR SEWING MACHINE
THE CONTROLS
Pattern selection dial
CAUTION
● When you use the pattern selection dial to choose a pattern, raise the needle by turning the handwheel toward you turn the pattern selection dial in the down position when you (counterclockwise) so that the mark on certain models. If the needle is in...
Operation Manual - Page 14
... is in the groove on the spool pin. KNOWING YOUR SEWING MACHINE
THREADING THE MACHINE
Winding the bobbin
CAUTION
● We designed the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other models, the machine will not work properly.
Only use bobbins from the spool 2 with your right hand, pass the...
Operation Manual - Page 16
KNOWING YOUR SEWING MACHINE
Lower threading
Install the bobbin wound with your finger, and then
pass the thread through the slit, as shown.
• If the thread is not correctly inserted through the tension-adjusting spring of the machine (as shown in the illustration). • Draw up the lower thread" on using the quick-set the bobbin so...
Operation Manual - Page 17
... thread is only available on page 15. Lower threading (for models equipped with thread. Put the 3 projection into the race retainer groove
and push closed.
1
Install the bobbin wound with a quick-set bobbin)
Replace the bobbin cover. This feature is not correctly inserted through the slit (1 and 2). When sewing gathers or darts, you to the steps in "Drawing...
Operation Manual - Page 22
... of the arrow, and leave it there
without drawing up the bobbin thread. Remove the bobbin cover, and then 1 reinstall the bobbin. Replace the bobbin cover.
4
2
1 Upper thread 2 Lower thread
Pull out about...lower and then raise the needle.
■ For models equipped with a quick-set bobbin
You can draw up the lower thread as described in . KNOWING YOUR SEWING MACHINE
Drawing up the lower ...
Operation Manual - Page 28
... to sew.
■ Correct tension
Correct tension is important as too much or too little tension will weaken your seams or cause puckers on your stitches.
In this case, refer to a lower number.
27 Note
● If the bobbin thread was incorrectly threaded, the upper thread may bend or break.
● The twin needle...
Operation Manual - Page 41
... the needle plate as difficulty turning the handwheel or an unusual noise, immediately stop using it may result, for example, rust caused by the user.
If problems occur, such as shown
in any of the locations described below, otherwise damage to the machine may reduce its efficiency.
1 Use the screwdriver
Grasp the bobbin case, and...
Operation Manual - Page 42
...; mark 3 Bobbin case • Make sure that you install the needle plate securely.
For a new bobbin case (part code: XE9326-001), contact your nearest authorized Brother Service Center.
● Make sure that the indicated points are
aligned before installing the bobbin case.
41 Insert the bobbin case so that the ▲ mark 7 on the bobbin case aligns with the ● mark
on machine as...
Operation Manual - Page 43
... the needle plate. Replace the bobbin case.
Fit the spool properly.
-
17
6
The area around the hole in the thread.
The bobbin case is incorrectly installed.
Loosen the upper thread tension.
27
42
If you have not used the foot controller properly.
Correctly install the needle.
8
The needle clamp screw is too tight. Visit us at " http://support.brother.com ". sew...
Operation Manual - Page 44
....
How to sew. Correctly install the needle. Use a bobbin that has been designed for this machine.
The needle is incorrect. The thread tension is bent or blunt.
The bobbin is tangled or breaks. Reset the bobbin thread correctly. Attach the presser foot that you are using . You have not used a bobbin that has been designed for this machine. Replace the bobbin case. Attach...
Operation Manual - Page 45
... the bobbin case.
Replace the needle.
If the thread is fitted on the wheel points up.
The thread is not correct for the type of stitch. The presser foot you are using is tangled, for the type of stitch that you want to sew. Choose a thread and needle that you want to sew.
Insert the needle properly. If...
Operation Manual - Page 46
... 17
L Light switch 8 Lower threading 15
M Main parts 6 Main power 8 Maintenance 40
N Needle
checking 8 combinations with fabric and thread ......... 22 replacing 8 Needle threader 19
O Overedge stitching 31
P Pattern selection dial 11 Patterns 11 Presser foot changing 10
, Q
Quick-set bobbin 16 21
45
R Race cleaning 40 Reverse sewing lever 12
, S
Spool pin 13 17 Stitches
built...
Brother International LX3817 Reviews
We have not received any reviews for Brother International yet.