Brother International 634D Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International 634D manuals!
Problems with Brother International 634D?
Ask a Question
Free Brother International 634D manuals!
Problems with Brother International 634D?
Ask a Question
Most Recent Brother International 634D Questions
Can I Get A Manual For My Brother Homelock/serger 634d With Differential Feed ?
(Posted by Niteworks3 3 years ago)
Needles For 634d Seeded
(Posted by Tspencer58 8 years ago)
I Am Looking For Instuctions On Cd For The Janame Mylock 634d
Can You Help
I am trying to find instructions on cd for the janome mylock 634d i have the vidio but nothing to pl...
I am trying to find instructions on cd for the janome mylock 634d i have the vidio but nothing to pl...
(Posted by stephowens 11 years ago)
Popular Brother International 634D Manual Pages
Users Manual - English - Page 1
... its fullest capacity unless it cannot operate to come. NOTE; You have just purchased an overlock sewing machine for purchasing an Overlock sewing machine. Please read the following instructions carefully so that your new sewing machine will give you very much for sewing all kinds of mm and cm into inches is handled correctly. The adjustment of * fabrics...
Users Manual - English - Page 2
... of thread tension adjustment
15
Sewing Pitch
17
Instruction for differential feed mechanism
18
Sewing
20
To start sewing
20
To remove work
20
If threads break during sewing
20
To sew thick material
21
Presser foot pressure
21
Fault-finding
22
Stitch Selection
23
How to use rolled hemming stitch attachment
24
Replacing the Blades
27
Oiling
28
Machine Specification...
Users Manual - English - Page 5
... to the front and insert it as far as
the needle stop. (3) Tighten the needle set screw securely, taking care that the needle is raised to avoid dropping it.
Needle se screw
Needle bar 0
*When the needles are inserted correctly, the right needle should be used on the machines. Needle
*TE x 1 (#11 & #14), DB x 1 (#9, 11, 14), DB x 1KN #11, 1738...
Users Manual - English - Page 6
Note: When sewing, ensure that the front cover is necessary to the counter-clockwise direction of an ordinary domestic sewing machine. Opening and closing the front cover
When threading, it is closed.
- 4- Turning direction of motor
Pulley
*The motor of this machine turns in a clockwise direction (direction of arrow), as opposed to open the front cover.
Users Manual - English - Page 8
...* When the motor is running, sparks can be noted that the motor of this sewing machine is 1,500 stitches per minute, which is quite fast compared to the normal operating speed... sewing machine.
* The bearings in the motor are made of a special, sintered oil-impregnated alloy mounted in the motor bracket on the side opposite the pulley. CAUTION
WHEN THREADING, REPLACING NEEDLE, OR WHEN MACHINE ...
Users Manual - English - Page 11
... the looper.
•oo
0o
0
0010
ao
Thread tension discs
0 0
NOTE If underlooper thread breaks during sewing. Make sure that re-threading is not accurate. Also, be sure thread is inbetween the tension disc. This can cause the breakage of the needles. Threading underlooper
* Run the thread in the sequence illustrated.
0 O
oC:=I
• 8
0
oCC.1 oCC)oa•-o
O
0•...
Users Manual - English - Page 12
CAUTION
Thread the needles after threading of underlooper and overlooper. Threading right needle * Run the thread in the sequence illustrated.
8 8 0
o=1 O1=
O
o
O
O
OO
0 8l 8
O
O
OO
0
- 10 -
Users Manual - English - Page 16
... clockwise increases the tension and turning counterclockwise slackens it impossible, adjust according to the illustrations "In this machine can be adjusted by four thread tension adjustment dials of the two needle threads, overlooper thread and underlooper thread. The correct thread tension varies with the type of fabric, the thickness of this
case" on following pages.
- 14 -
Upper...
Users Manual - English - Page 22
... fabric will destroy the needles and blades. r
off is finished,
keep the machine running at
low speed to sew. Then cut the stitches 5 cm (2 inches) from the work
N
*When the seam is not
enough, pull the thread gently.
(1
If threads break during sewing
* Remove the material and
rethread correctly.
You need only guide it is not uniform...
Users Manual - English - Page 23
... by turning the pressure adjustment screw. Then, start sewing.
* Do not lift the presser foot while sewing.
%
To sew fine material
(1) Adjust the pressure to prevent material from puckering and to facilitate sewing curves.
(2) Slacken the thread tension, but remember that if the tension is too slack this machine has already been adjusted to a pressure suitable...
Users Manual - English - Page 24
... tension too tight. Improper threading Thread correctly.
Replace with new needle.
2.
Check spool pin, thread holders, etc. too weak.
See pages 14-16 "Thread tension".
6. Needles incorrectly fitted. Thread correctly. (See pages 7-11.)
2. Improper threading.
Fabric
1. Fault-finding
This sewing machine is designed for trouble-free operation. and remove...
Users Manual - English - Page 25
... right needle when
sewing this overlock stitch. 4.
Three-thread overlock stitch (2.8 mm/ 3/16 inch)
Use three threads and right needle, producing 2.8 nnm, (3/-io inch) seams. Use: For overlock stitching and
sewing suits, blouses, slacks, etc. Four-thread overlock
stitch
Use all kinds
)73
of stitches in simple steps as
follows;
1. ments.
2. Stitch selection
These sewing machines can...
Users Manual - English - Page 28
...equipped to prevent lower blade from exceeding 5 mm (1/4 inch).
(A) For rolled hemming stitch
O
Rolled hemming needle plate
(B) For regular stitch
- To do this, press in at the left of the blade and ...turn in the direction of the arrow illustrated, until it snaps into a locked position. (3) Loosen the set on 5 mm)
The bight size for the lower blade holder. (4) Move the lower ...
Users Manual - English - Page 30
... avoid oil stains. 0
3
- 28 - Wipe
off excess oil with a scrap piece to oil your sewing machine before use. 2. Oiling
For smooth and silent operation the moving parts of the machine should be oiled periodically. (See diagram below.) REMARKS: 1. After oiling, run the machine without thread and the presser foot up. OIL ONCE OR TWICE A MONTH IF...
Users Manual - English - Page 31
Sewing speed
1,500 stitches per minute
Ball point #11: 2 pcs.
Bight size
2.8 mm and 5.0 mm (34/ 6 to 1/4 inch)
Upper blade
krt
Stitch length (pitch)
2 mm to 5 mm CA to heavy weight materials
Standard #14: 2 pcs. of needles and threads
Three/Four threads convertible Two needles or single needle
Machine net weight
7.0 kgs.
Machine Specification
Model No.
634D
Needle set
Use
...
Brother International 634D Reviews
We have not received any reviews for Brother International yet.