Biostar M7TDB Support and Manuals
Get Help and Manuals for this Biostar item
View All Support Options Below
Free Biostar M7TDB manuals!
Problems with Biostar M7TDB?
Ask a Question
Free Biostar M7TDB manuals!
Problems with Biostar M7TDB?
Ask a Question
Popular Biostar M7TDB Manual Pages
M7TDB user's manual - Page 13
... − Offers the highest performance for MS-DOS, Windows NT, Windows 2000, Windows 95/98, Windows ME, Windows XP, Novell, LINUX, UNIX, SCO UNIX etc.
1.1.4 Accessories
− HDD Cable. − FDD Cable. − Flash Memory Writer for BIOS Update. − USB Cable (Optional). − Rear I/O Panel for ATX Case (Optional). − Fully Setup Driver CD.
1-7
M7TDB user's manual - Page 20
... 1
Motherboard Description
Install DIMM3/4 in any memory on DIMM3. Don't stuff or remove the DIMM memory, if the LED1 is only for DRAM configuration is lighting. 2. If you must use double-sided memory on DIMM3, please do not insert any combination table:
DIMM3 Double
X Single
DIMM4 X
Double Single
* This M7TDB motherboard does not support with...
M7TDB user's manual - Page 38
...Configuration Data) write is then stored in your system using Setup. BIOS Setup
Introduction
This manual discussed Award™ Setup program built into the ROM BIOS.
The rest of the chipset controlling the entire system.
EPA Green PC Support
This AWARD BIOS supports Version 1.03 of the Advanced Power Management (APM) specification. Power to the hard disk drives and video monitors...
M7TDB user's manual - Page 61
...set CMOS to enter the Soft-Off state when the system has "hung." There are 3 options: "Former-Sts", "On", "Off". the motherboard...15Min. For example: If set time of the CMOS when AC power is lost power previously without any subsequent manual intervention.
There are 3 ... , then after the set to a system that retains these Power-On instructions; Chapter 2
BIOS Setup
HDD Power Down
When ...
M7TDB user's manual - Page 71
... click Next to select the hardware form a list. A dialog box will pop up , Windows system will be installed through the following steps : 1. Chapter 3
RAID Setting Guide
3.2 Installation of Driver
3.2.1 Introduction
After the computer start -up , input the path of driver A:\Win9X.Then click OK to continue. 8. Select No,I want to continue. 5. When finished, restart the computer...
M7TDB user's manual - Page 72
... that the driver has been installed properly. Select Device Manager item from the popup menu. 2. on desktop, and then select Property item from the popup window. Right-click My Computer icon on device icon, it indicates that the driver has not been correctly installed and needs reinstallation.
3-3 Chapter 3
RAID Setting Guide
Verify Installation
When the driver has been...
M7TDB user's manual - Page 74
... is HPT370 UDMA/ATA100 RAID Controller item in the popup window, it indicates that the driver has been successfully installed. Otherwise, users need to reinstall the driver.
3-5 Click Start-->Setup-->Control Panel, and then double-click SCSI Adapter item. 2. Chapter 3
RAID Setting Guide
Verify Installation
When the driver has been successfully installed and the computer restarted: 1.
M7TDB user's manual - Page 75
... Add/Troubleshoot a device, then click Next to continue.
3. Manual Installation If Windows can not find new hardware, the driver shall be installed through the...Setup-->Control Panel, select Add/Remove New Hardware. Then click Next to finish the installation, and restart
the computer. Chapter 3
RAID Setting Guide
3.2.4 Windows 2000
Install driver under Windows 2000
Automatic Installation...
M7TDB user's manual - Page 76
... type, please select Other and press Enter to install driver under Windows 2000. 6.
The follow -on interface will ask whether to install driver under WinNT or under Windows 2000, please select to continue. 4.
Otherwise, please reinstall the driver.
3-7 Chapter 3
RAID Setting Guide
restarted, press F6 key when the message Setup is HPT370 UDMA/ATA100 RAID Controller item in...
M7TDB user's manual - Page 107
.... Reformat the hard drive. Hard disk directory or FAT is impossible.
Make sure both
DRIVE SPECIFICATION.
Re-install applications and
data using backup disks.
4-2
PROBABLE CAUSE
DIAGNOSIS
SOLUTION
Connector between hard When attempting to do so the hard support.
Damaged hard disk or disk controller. Backing up onto hard drive. PROBABLE CAUSE
DIAGNOSIS...
M7TDB user's manual - Page 110
....
Hard drives not compatible / different manufacturers. Call drive manufacturers for compatibility with other drives.
4-5 If no color replace monitor. DIAGNOSIS
SOLUTION Check hard drive cable. PROBLEM
Cannot boot system after installing second hard drive. PROBABLE CAUSE
Master/slave jumpers not set up.
Chapter 4
Trouble Shooting
No color on screen.
Call technical support.
M7TDB compatibility test report - Page 1
M7 TDB ENGINEERING VALIDATION TEST REPORT
COVER SHEET
CHANGE CONTROL Description of Change
Initial Release
Revision 0.91 1.1 1.2
Sections/Pages Affected
Date 2001/5/24 2001/7/2 2001/7/20
Project: Date: Owner: Contact:
M7 TDB Intel 845 For Pentium 4/Socket 478 ATX Motherboard 2001/9/24 Biostar Group TEL: 886-2-2218-0150 FAX: 886-2-2218-1552 Home Page: http://www.biostar.com.tw
1
M7TDB compatibility test report - Page 2
CONTENTS PRODUCT INFORMATION 4
Motherboard General Information 4 Chipset Details...4 BIOS Details...4 CPU Supports ...4 Memory Supports ...4 On-board Features and Devices 4 Mechanical...5
DESIGN REVIEW 7
Mainboard Voltage Measurement 7 Bus Clock ...7
REQUIRED BIOS DEFAULT SETTINGS 8
BIOS FEATURES SETUP 8 CHIPSET FEATURES SETUP 8 POWER MANAGEMENT SETUP 8 PnP / PCI CONFIGURATION 9 ...
M7TDB compatibility test report - Page 4
...
No of PCI Full Length Slots
3 4 5 6
No of ISA Full Length Slots AMR Slot Support CNR Slot Support ACR Slot Support
1 2 3 4 None
Yes
No
Yes
No
Yes
No
Number of Memory Slots
DIMM 3+1 .
PRODUCT INFORMATION
Motherboard General Information
Vendor
Biostar
Model Number Version Number Platform
M7 TDB V0.91/V1.1/V1.2
AT ATX
Micro ATX
Flex ATX...
M7TDB compatibility test report - Page 61
Ver 1.2
Motherboard General Information
Vendor
Biostar
Model Number
M7TDB
Revision
1.2
Temperature ( ℃ ) 35 ℃
Humidity rate ( % ) 0 ~ 60 %
Thermo Tracer
NEC TH5104
Test Program
3Dmark2000
Comments: The component temperature measured value was based on 35℃ check in the
chamber and the system during in the 3Dmark2000 Looping testing.
61 THERMAL IMAGE TEST -
Biostar M7TDB Reviews
We have not received any reviews for Biostar yet.