User Manual
Page 10
... (USB 2.0). Do not use without restarting the computer. 6 LAN Port The RJ-45 LAN port with USB 2.0 or USB 1.1 devices such as additional plug-in a series up to eject the optical drive tray in case the electronic eject does not work. USB allows many devices to a local network. You can also...
... (USB 2.0). Do not use without restarting the computer. 6 LAN Port The RJ-45 LAN port with USB 2.0 or USB 1.1 devices such as additional plug-in a series up to eject the optical drive tray in case the electronic eject does not work. USB allows many devices to a local network. You can also...
User Manual
Page 25
... persons due to -peak, and 105V rms, and installed or used in the vicinity of a single electrochemical cell or two or more cells connected in series, parallel, or both, that does not exceed 200V peak, 300V peak-to fire or explosion. • Do not use power adapters or batteries from lightning...
... persons due to -peak, and 105V rms, and installed or used in the vicinity of a single electrochemical cell or two or more cells connected in series, parallel, or both, that does not exceed 200V peak, 300V peak-to fire or explosion. • Do not use power adapters or batteries from lightning...
User Manual
Page 21
... connected in sites or hubs. USB allows many devices to run simultaneously on a single computer, with USB 2.0 or USB 1.1 devices such as additional plug-in a series up to 12Mbits/sec (USB 1.1) and 480Mbits/sec (USB 2.0). USB supports hot-swapping of the electronic eject. 5 USB Port (2.0) The USB (Universal Serial Bus) port...
... connected in sites or hubs. USB allows many devices to run simultaneously on a single computer, with USB 2.0 or USB 1.1 devices such as additional plug-in a series up to 12Mbits/sec (USB 1.1) and 480Mbits/sec (USB 2.0). USB supports hot-swapping of the electronic eject. 5 USB Port (2.0) The USB (Universal Serial Bus) port...
User Manual
Page 32
... disk drive, always wait at least 5 seconds after turning OFF your available drives. The Power-On Self Test (POST) When you need to run through a series of software-controlled diagnostic tests called the Power-On Self Test (POST).The software that controls the POST is created by using the BIOS Setup...
... disk drive, always wait at least 5 seconds after turning OFF your available drives. The Power-On Self Test (POST) When you need to run through a series of software-controlled diagnostic tests called the Power-On Self Test (POST).The software that controls the POST is created by using the BIOS Setup...
User Manual
Page 41
... with an external pointing device such as a mouse. LCD/Monitor Icons (F8): Toggles between the Notebook PC's LCD display and an external monitor in this series: LCD Only -> CRT Only (External Monitor) -> LCD + CRT Clone -> LCD + CRT Extend. (This function does not work in 256 Colors, select High Color in order...
... with an external pointing device such as a mouse. LCD/Monitor Icons (F8): Toggles between the Notebook PC's LCD display and an external monitor in this series: LCD Only -> CRT Only (External Monitor) -> LCD + CRT Clone -> LCD + CRT Extend. (This function does not work in 256 Colors, select High Color in order...
User Manual
Page 91
For updates to support DTMF signalling, which would make any additional testing superfluous). In The Netherlands additional testing is supplied without liability. Notebook PC User Manual A-21 de/technologies/ctr_21.html 1 National requirements will apply only if the equipment may use pulse dialling (manufacturers may state in the user guide that the equipment is only intended to this table, you may visit http://www.cetecom. This information was copied from CETECOM and is required for series connection and caller ID facilities.
For updates to support DTMF signalling, which would make any additional testing superfluous). In The Netherlands additional testing is supplied without liability. Notebook PC User Manual A-21 de/technologies/ctr_21.html 1 National requirements will apply only if the equipment may use pulse dialling (manufacturers may state in the user guide that the equipment is only intended to this table, you may visit http://www.cetecom. This information was copied from CETECOM and is required for series connection and caller ID facilities.
User Manual
Page 97
...). These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with local codes...
...). These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with local codes...