Adaptec ULTRA160 - Pci To SCSI Card Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec ULTRA160 manuals!
Problems with Adaptec ULTRA160?
Ask a Question
Free Adaptec ULTRA160 manuals!
Problems with Adaptec ULTRA160?
Ask a Question
Popular Adaptec ULTRA160 Manual Pages
Installation Guide - Page 3
... LVD/SE Connector 68-pin Internal SE Connector
68-pin External LVD/SE Connector
50-pin Internal SE Connector Although the Adaptec SCSI Card 29160 is a 64-bit PCI card, it also works in the slower 32-bit mode. This installation guide explains how to
• Install the Adaptec SCSI Card 29160 • Set up to 15 SCSI devices-such as hard disk drives, scanners, and CD-ROM drives...
Installation Guide - Page 4
... up to Ultra SCSI performance levels. Installation Guide
Bus Segments on the SCSI bus.
This allows the Adaptec SCSI Card 29160 to support LVD SCSI devices at speeds up to 40 MBytes/sec on the primary LVD/SE segment while at the same time supporting Ultra (legacy) devices at the maximum possible rate (80 MBytes/sec for Ultra2 devices and 160 MBytes/sec for Ultra160 devices).
4 The...
Installation Guide - Page 5
... Slot
5 WARNING Turn OFF power to the computer and disconnect the power cord.
Adaptec SCSI Card 29160
INSTALLING THE ADAPTEC SCSI CARD 29160
STEP 1
Discharge any static electricity build-up before handling the SCSI card by touching a grounded metal object (like the exposed metal parts on the back of your computer and unplug the power cord, remove the cover...
Installation Guide - Page 6
... slot. STEP 4
Insert the Adaptec SCSI Card 29160 into the PCI expansion slot; Refer to your computer is a tower model, lay it on its side to make it easier to locate the PCI slots. Installation Guide
Computers may break if you force it into place, then replace the slot cover screw. If your computer manual to install the Adaptec SCSI Card 29160.
Installation Guide - Page 7
...; Refer to SCSI ID 0 at the end of each device you are some guidelines for specific instructions. SCSI IDs for more information on the back of each cable. Internal LVD cables
7 Terminators must be removed, or termination must be changed. Check the SCSI IDs
The Adaptec SCSI Card 29160 and each cable, or the end of the cable itself, must have a terminator installed (or...
Installation Guide - Page 8
... an LVD terminator to terminate the last device in the chain. On most internal Ultra SCSI and Fast/Wide SCSI devices, the termination setting is controlled by physically removing or installing a resistor module(s).
For more information, refer to the documentation for instructions on all internal devices connected to the cable. Internal SCSI Device Mounted in an available drive bay inside...
Installation Guide - Page 9
... the devices:
NOTE We recommend that you keep your LVD SCSI devices separate from your SE (Ultra SCSI) devices. Follow these steps to the Adaptec SCSI Card 29160 User's Reference.
Connecting Internal LVD SCSI Devices
Connect internal LVD SCSI devices to review Setting Up SCSI Devices on page 7. To do this, use a 68-pin internal LVD cable like the one shown in Step 1 below or flat...
Installation Guide - Page 10
... at the terminated end of the cable. Installation Guide
STEP 2
Plug the nonterminated end of the cable to the internal LVD/SE connector.
68-pin Internal LVD SCSI Cable
68-pin Internal LVD/SE Connector
STEP 3
Plug the internal LVD SCSI devices to this Connector on page 7 for more information.
10
LVD (e.g., Ultra160 or Ultra2) SCSI Devices
Plug First Device Built-in Terminator...
Installation Guide - Page 11
Adaptec SCSI Card 29160
STEP 4
Connect a power cable from your computer's internal power supply to connect the devices:
Locate a 68-pin internal Wide SCSI cable.
11 Follow these steps to each internal SCSI device. To do this, use a 68-pin Wide SCSI cable like the one shown in Step 1 below. Power Cable (From the Power Supply Inside the Computer)
Power Input...
Installation Guide - Page 15
Adaptec SCSI Card 29160
STEP 5
Connect a power cable from your computer's internal power supply to the external SCSI connector.
NOTE We recommend that you also attach older Ultra SCSI devices, the data transfer speed of the LVD SCSI devices will require a 68-pin external LVD SCSI cable. Each external device will drop to the 68-pin external LVD/SE SCSI connector. Power Cable (From the ...
Installation Guide - Page 17
... operating system manual or contact the operating system vendor for information.
17 To determine if the card is already installed. Adaptec SCSI Card 29160 STEP 4 Connect power cables to all external devices and to the Ultra160 Family Manager Set User's Guide and Adaptec SCSI Card 29160 User's Reference for instructions on either installing driver software when installing your operating system...
Installation Guide - Page 18
....
18 If you have any problems while installing the Adaptec SCSI Card 29160, check the following items first:
• Are all SCSI devices powered on? • Are all SCSI cables and power cables properly connected? • Does each device on the SCSI bus have a unique SCSI ID? • Does the total SCSI cable length exceed the maximum allow- Installation Guide
TROUBLESHOOTING
If you are still...
Installation Guide - Page 20
.... assumes no liability resulting from errors or omissions in the U.S. Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER REMEDIES. Copyright
© 2000 Adaptec, Inc. Adaptec reserves the right to make...
Installation Guide - Page 21
... instruction manual, may cause harmful interference to correct the interference by the Spectrum Management Agency...shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to Part 15 of the following European... set out by one or more of the FCC rules.
Adaptec SCSI Card 29160
Tested...energy, and if not installed and used in accordance with part 15 of the FCC ...
Installation Guide - Page 24
AA) All rights reserved. R
We move the information that moves your world.™
© 2000 Adaptec, Inc. Printed in Singapore
Stock No.: 512520-03, Rev. A RAC 1/00 (SRC: 512520-00, Ver.
Adaptec ULTRA160 Reviews
We have not received any reviews for Adaptec yet.