Adaptec ASR-2000S - SCSI RAID 2000S Storage Controller Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec ASR-2000S manuals!
Problems with Adaptec ASR-2000S?
Ask a Question
Free Adaptec ASR-2000S manuals!
Problems with Adaptec ASR-2000S?
Ask a Question
Popular Adaptec ASR-2000S Manual Pages
Installation Guide - Page 10
Adaptec RAID Installation Guide
Read this First
Before you begin installing your new Adaptec RAID controller, read this chapter. Adaptec 2100S/3200S/3210S/3400S/3410S only
Storage Requirements for Drivers and Software
Adaptec Storage Management software and device drivers require approximately 4 MB of memory, and a Pentium processor that is an important guide to the rest of the documentation ...
Installation Guide - Page 11
... with 1 internal LVD SCSI cable with the PCI Local Bus Specification (revisions 2.1 and 2.2).
s Supports multifunction devices where one of motherboards that s Complies with active terminator s Registration and warranty cards s Adaptec RAID Installation Guide (this book) s Adaptec RAID Installation CD, a bootable CD that includes RAID management software, drivers, and documentation
1-3
Installation Guide - Page 12
... RAID 0 or RAID 5 arrays with the NTFS file system. Refer to 66 MHz. Adaptec RAID Installation Guide
Adaptec RAID Controller Features
Adaptec RAID controllers support s RAID levels 0, 1, 5, multilevel 0/1 and 0/5. s PCI Local Bus Specification, Revision 2.2 with ECC and predictive caching. s Windows 2000 and Windows NT only-Array expansion and extension during normal operation on capacity...
Installation Guide - Page 14
.... About the Documentation
The complete documentation set for both applications are included on the Adaptec RAID Installation CD.
Using the Adaptec RAID Installation CD
The Adaptec RAID Installation CD contains the RAID Management Software, device drivers, and user documentation needed to 2 Terabytes of the following:
s Adaptec RAID Installation Guide (this book)-Contains information that may...
Installation Guide - Page 19
.... For an overview of the Adaptec RAID Installation CD. If you do so now. Software installation procedures are building a new system, installing the driver involves installing the operating system, too. Refer to Chapter 2.
6 Install the controller driver according to the instructions in Chapter 2.
5 Use SMOR to check your cache memory module or set up the controller and configuring the...
Installation Guide - Page 21
..., refer to do such things as create and manage RAID arrays, set up security levels for users and administrators, establish the means of notifying users of supporting the following software tools to it's Java-based architecture). Introduction
Storage Management Software Overview
Your Adaptec RAID controller includes the following additional operating systems:
s Windows Me...
Installation Guide - Page 43
... an Existing System on page 2-10.
5 Insert the Windows NT CD in drivers. Press S to create the RAID.
To create the disk a Insert the Adaptec RAID Installation CD in your system. 8 You are removing a controller from the CD. Adaptec RAID Installation Guide
4 Start up the system. Windows NT detects any further detection. 7 Shut down and restart...
Installation Guide - Page 47
... that applies to establish CD-ROM support. Identify the scenario that you doing a full installation on an ATA controller, use your CD drive to your Adaptec RAID controller and hard drives according to the instructions in the drive and type
d:\setup where d: is on an Adaptec SCSI RAID controller, create a driver disk for Windows as described in...
Installation Guide - Page 58
... specified by the controller; To install the driver
1 Upgrade your drive and a blank floppy disk in the floppy disk drive. To create the disk a Insert the Adaptec RAID Installation CD in the install process. 5 Start up the server. you will need this scenario, you created in Step 2 and install I2O and block storage support only. 11 Accept the...
Installation Guide - Page 60
...created in \packages\netware\5.x\driver to the instructions in an Existing NetWare 5 Server
In this information later in the floppy disk drive.
During startup, press Ctrl+A to create the RAID. Installing the Driver in Chapter 2. c Remove the Adaptec RAID Installation CD and the driver floppy disk.
3 Shutdown the server. 4 Install and configure the Adaptec RAID controller as a secondary...
Installation Guide - Page 70
... the Adaptec Storage Manager Pro User's Guide. Storage Manager Pro requires approximately 60 MB of disk space. After the installation is required to run Storage Manager Pro.
Note: Do not install Storage Manager Pro on a network drive, because Storage Manager Pro runs as a Windows NT/2000 service and services do not have Storage Manager Pro installed on Windows...
Installation Guide - Page 73
...apps\SMPro\setup.nlm
3 If Storage Manager Pro is already installed, you must uninstall Storage Manager Pro before reinstalling it. If Storage Manager Pro is not already installed, skip this...
1 Install the minimum support packs for installing Storage Manager Pro in sys:\adaptec\smpro.
5 Press Enter to continue or F3 to uninstall.
4 From the Select Product Option window, select Adaptec Storage ...
Installation Guide - Page 93
... a variety of problems, particularly with the Adaptec controller. Adaptec 2400A/2100S/3200S/3400S only- A memory module other LEDs) remains lit. Adaptec RAID Installation Guide
The controller fails to... the controller IRQ assignment is set to respond.
C-2
The IRQ LED indicates that the controller is a PCI bridge or because it does not support multifunction devices where one of ...
Installation Guide - Page 94
... faulty hard drive or cable is garbled. If the error persists, contact Adaptec Technical Support.
During the installation of these reserved interrupts. Reset the NVRAM to Appendix D. To reset the NVRAM, refer to the default settings and reconfigure the RAID. Restart the computer. After updating the Adaptec controller firmware or BIOS and restarting, the controller does not respond...
Installation Guide - Page 95
... code detected a firmware checksum error or a flash error. For details, refer to Appendix D. Upgrade SMOR using the flash Mode 0 procedure. For details, refer to Appendix D. For details, refer to Normal. A firmware upgrade is used to hang the system. The floppy disk drive cannot be accessed after installing an Adaptec controller.
After updating the Adaptec controller firmware...
Adaptec ASR-2000S Reviews
We have not received any reviews for Adaptec yet.