Adaptec 1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 1130U2 manuals!
Problems with Adaptec 1130U2?
Ask a Question
Free Adaptec 1130U2 manuals!
Problems with Adaptec 1130U2?
Ask a Question
Popular Adaptec 1130U2 Manual Pages
Hardware Guide - Page 8
...Utility
Starting the SCSISelect Utility A-2 Using SCSISelect Menus A-2 Exiting SCSISelect A-3 Using the SCSI Disk Utilities A-3
SCSISelect Settings A-4 SCSI Bus Interface Definitions A-4 SCSI Device Configuration A-5 Additional Options A-6
B Using the ARO-1130U2 with Other Adaptec Products
Using Driver Disk B B-2 Using the ARO-1130U2 with an AHA-294x, AHA-3940, or
Other AIC-78xx Based Host Adapter...
Hardware Guide - Page 11
...however, only motherboards with RAIDport™ I motherboards.
The ARO-1130U2 can be used in a RAIDport II system; See the Adaptec Web Site at http://www.adaptec.com/raid for instructions on the system motherboard. This Installation and Hardware Guide explains how to install the ARO-1130U2, run the Array1000 BIOS & Driver Selection Utility, run the ArrayConfigU2™ Utility to the...
Hardware Guide - Page 35
... driver (cda1000.sys) for instructions on installing and using the ArrayConfigU2 Utility, if you have completed the following:
s Installed the ARO-1130U2 in your system. (See Chapter 2) s Run the Array1000 BIOS & Driver Selection Utility to add, delete, and manage arrays from the server console. 5 w w w w
Installing the Software Driver for Windows NT
This chapter explains how to the Adaptec...
Hardware Guide - Page 36
... on page B-2 for Windows NT
To begin driver installation, see Using the ARO-1130U2 with the RAIDport), the NT driver for these adapters must be from the Adaptec 7800 Family Manager Set 2.10 or higher. AND 2) has an Adaptec AHA-294x host adapter installed; Installing the Array1000U2 Driver for instructions on page 5-4. ARO-1130U2 Installation and Hardware Guide
Note: If your system: 1) is...
Hardware Guide - Page 37
... displays the adapter drivers supported on the
diskette. insert the Appropriate Adaptec
Array1000U2 Family Manager Set driver diskette (Disk A or Disk B) in your floppy disk drive and press Enter. (See Running the Array1000 BIOS & Driver Selection Utility on page 5-5.
1 Start your system with Step 3 below . Setup is enabled in SCSISelect.
2 Windows NT Boot Diskette installation: When prompted...
Hardware Guide - Page 38
... the ARO-1130U2),
press S and repeat Step 5 for each additional adapter and insert the appropriate disk provided by default.
8 In the Install Driver window, Click OK. 9 You must restart your computer for the changes to take effect. ager Set driver diskette (Disk A or Disk B) in the Windows NT documentation to Settings.
3 Click the Control Panel. 4 Double-click the SCSI...
Hardware Guide - Page 41
... 4.11 and 5.0). Before installing the driver, make sure you plan to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the ArrayConfigU2 Utility, if you have completed the following:
s Installed the ARO-1130U2 in your system (See Chapter 2) s Run the Array1000 BIOS & Driver Selection Utility to install the ARO-1130U2 software driver (cda1000h.ham) for...
Hardware Guide - Page 42
... II or III equipped; ARO-1130U2 Installation and Hardware Guide
Note: If your RAIDport III system has an Adaptec AIC-78xx device (for example, AHA-2940 or AHA-3940 host adapter) installed (which is not associated with the RAIDport), the NetWare driver for Novell NetWare
To begin driver installation, see Appendix B, Using the ARO-1130U2 with Other Adaptec Products.
6-2 Ultra2 SCSI host adapters...
Hardware Guide - Page 44
Refer to the Adaptec CI/O Management Software User's Guide for
installing a new server.
10 If prompted to the cda1000h.ham driver. ARO-1130U2 Installation and Hardware Guide
9 Follow the procedures in \netware\v4_1x on the diskette.
15 Select cda1000h.ham and press Enter. 16 When prompted to save existing file c:\nwserver\nbi....
Hardware Guide - Page 47
...the server by entering
down
6-7 Delete any Multiple Processor Support module that are
prompted to Add, Change, or Delete drivers as your storage adapter.
17 Remove the diskette from ...documentation to
complete the installation.
20 When installation is
detected (for the server, you are
not present in your system.
11 Insert the Adaptec Array1000U2 Family Manager Set driver
diskette in your ...
Hardware Guide - Page 51
...
This chapter explains how to install the ARO-1130U2 software driver (cda1000) for instructions on installing and using the ArrayConfigU2 Utility, if you have completed the following:
s Installed the ARO-1130U2 in your system. (See Chapter 2) s Run the Array1000 BIOS & Driver Selection Utility to deter- mine which of the two Array1000U2 Family Manager Set driver diskettes (Disk A or Disk B) is...
Hardware Guide - Page 52
... for the first SCO UnixWare installation screen and prompt to appear, then follow the instructions below , or Installing the Driver When SCO UnixWare is Already Installed on page 7-4 for instructions.
7-2
ARO-1130U2 Installation and Hardware Guide
Installing the Array1000U2 Driver for UnixWare
To begin driver installation, see either Installing the Driver When Installing SCO UnixWare below...
Hardware Guide - Page 62
...
ARO-1130U2 Installation and Hardware Guide
Using Driver Disk B
If the Array1000 BIOS & Driver Selection Utility determines you require Disk A of the manager set driver diskettes, follow the instructions in...Driver Disk B (Windows NT Only) below that requires driver Disk B, these Adaptec products:
s AHA-294x, AHA-3940, or any of the above host adapters.
You will need to install drivers...
Hardware Guide - Page 63
... ARO-1130U2 with Other Adaptec Products
Scenario #1: Adding an ARO-1130U2 to a RAIDport II or III System with an AHA-294x, AHA-3940, or Other AIC-78xx Based Host Adapter
These instructions assume that the boot drive is currently connected to an AHA-294x, AHA-3940, or any changes to it. Installing the ARO-1130U2 Driver
1 Start the Windows NT Control...
Hardware Guide - Page 67
... the ARO-1130U2 with the new configuration.
2 Run the Registry Editor (regedit.exe). 3 When the Registry Editor window appears, expand the tree on
the left until you can see the nodes under \HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services.
4 Select cda1000 on the left part of the screen. Caution: It is a problem with Other Adaptec Products
Changing Registry Settings
1 Back...
Adaptec 1130U2 Reviews
We have not received any reviews for Adaptec yet.