AIWA CDC-Z107 Support and Manuals
Get Help and Manuals for this AIWA item
View All Support Options Below
Free AIWA CDC-Z107 manuals!
Problems with AIWA CDC-Z107?
Ask a Question
Free AIWA CDC-Z107 manuals!
Problems with AIWA CDC-Z107?
Ask a Question
Most Recent AIWA CDC-Z107 Questions
How Do I Turn The Power Off Once Its One
i got it to turn on but once the player is on it wont shut off. what could be my problem
i got it to turn on but once the player is on it wont shut off. what could be my problem
(Posted by Anonymous-111301 10 years ago)
Popular AIWA CDC-Z107 Manual Pages
Service Manual - Page 1
CDC-Z107 YU
SERVICE MANUAL
STEREO CAR CD RECEIVER
BASIC CD MECHANISM : TN-CCD1001-113J
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual" of CDC-Z107, (S/M Code No. 09-99B-422-4T1).
S/M Code No. 09-002-422-4R1
REVISIODNATA
Service Manual - Page 2
...-010
IB,INST,YU,YL (3L,P) IB,YU(3L) 107 NUT...- 2 -
NO. SPECIFICATIONS
RADIO SECTION
(FM)
...Installation Size
182 (W) x 53 (H) x 155 (D) mm
(71/4 (W) x 21/8 (H) x 61/8 (D) inches)
• Design and specifications... are subject to the 10k position [for your area using the switch on the bottom of the unit. (The switch is set... µV (30 dB)
Set the frequency increment for the...
Service Manual - Page 3
...P.C.B
- 3 - PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. IN CASE IT IS NECESSARY TO CONFIRM LASER ...LASER LAITE LASER APPARAT
Precaution to follow carefully the instructions below when servicing. Be sure ground body and workbench, and use...er ude af funktion. VARNING! Therefore, be sure to replace Optical block
(OPTIMA-720AIE)
Body or clothes electrostatic potential...
Service Manual - Page 5
L831 L881 R241 R242 SW702
PART NO.
KANRI
DESCRIPTION
NO.
87-010-498-040 CAP,E 10-16 GAS
87-010-196-080 CHIP CAPACITOR,0.1-25
87-010-555-040 ...87-003-149-080
ANT,AW-002 JACK,PIN 2P XR-401 COIL 4.7 UH COIL,68MH K7-D COIL,47UH
REF. C316 C321 C322 C323 C324
PART NO. REF. KANRI
DESCRIPTION
NO.
87-003-143-080 COIL,4.7UH K LAL02
8Z-KT1-615-010 FLTR,AMORPHOUS -CHOKE
87-022-371-080 C-RES...
Service Manual - Page 23
...output terminal for DSP.
Hi=MONO, Low=ST FM reception.
14
SD/ST
I
Sub-code Q output standby input terminal.
- 23 - Hi=LOC, Low=DX
16
IF REQ....
7
LCD DI
I
LCD driver data signal input.
8
LCD DO
O
LCD driver data signal output.
9
LCD CLO
O
LCD driver clock signal output.
10
LCD CE
O
LCD driver CE signal output.
11
SQ OUT
I
Initial setting diode matrix input.
31
VDD
...
Service Manual - Page 24
...used . Pulled up inner track position detection. I
Remote controller input.
I
IF count signal input (FM / AM).
- Power supply. O
Error out from charge pump (for level indecator.
I
Backup detection.
-
H: No light on, L: Light on.
- Pulled down when not used... EO2 EO1 NC XOUT
I
LCD driver data signal input. I
Voltage input for FM / AM).
- Low=-20dB mute.
Service Manual - Page 25
... control signal output.
I
Inputs the DC components in the spindle 12cm mode. I
Sets the amplitude of analog signals.
pins. I
Tracking gain control signal input from the ...Sets the time constant for the tracking gain. I
Spindle amp input.
I
TES (track error sense) comparator input.
Off when TOFF is "H". For the connection of a resistor which sets...
Service Manual - Page 26
... used to control the DSP's data slice level of RF signal circuits.
- 26 - Sets the time constant for the focus search smoothing capacitor. I
Microprocessor chip enable input. For ...
Disc defect detection output.
For the connection of bypass capacitor for the reference voltage.
I
CLV error signal input from the DSP. O
Output for disc defect detection.
-
I
Input to hold...
Service Manual - Page 27
Digital system ground. (Must be set to three-value output by microprocessor command. Can be ... pull-down resistor is built-in . (Must be connected to 0V.) PDO output current adjustment resistor connection. VCO frequency range adjustment. Tracking error signal input. Digital system power supply. CONT1 ~ 5
I/O
EMPH/CONT6
O
C2F
O
DOUT
O
TEST3
I
TEST4
I
34
PCCL
I
17...
Service Manual - Page 28
...be connected to 0V.)
- 28 - XOUT
O
XIN
I
Description Right channel ground. (Must be set low briefly after power is a Schmitt input. Right channel mute output./ General purpose input/ output. ....
MUTER/CONT8 O
XVDD
- Right channe power supply. C1, C2, sigle an double error correction monitor. This pin must be connected to 0V.) Subcode clock synchronization signal output. A...
Service Manual - Page 29
... compensation capacitors must be connected between VREF and - Not used .
-
The front and rear sides can be attenuated independently. Data is activated. VSS as a troubleshooting against power ripples. I
Super bass input. Not used .
-
Ground. Chip enable.
O
Fader outputs.
Must be attenuated independently.
-
I
Signal input pins.
37
TUN(L)
38
TP...
Service Manual - Page 30
... GND.)
56
VDD
- synchronization.
64
DI
O
Serial data interface pin; Pin Name
I/O
Description
1 ~ 40
S1 ~ S40
O
LCD segment output.
41 ~ 43
COM1~ COM3
O
LCD command driver outputs.
44 ~ 49
KS1 ~ KS6
O
Key scan outputs.
50 ~ 54
KI1 ~ KI5
I /O Resistor and capacitor are attached externally form an oscillator circuit.
61
DO
O
Serial...
Service Manual - Page 31
... Back • Focus search is contiuned if
TOC cannot be lighted as shown in the driver IC
if the focus search is started, all modes except search mode. * NOTE 1 : There are CD operations are cyclic • "Error 03" is up
against Step 1 • Step 3 : For CD-R Laser Power Up
against Step 2
Contents...
AIWA CDC-Z107 Reviews
We have not received any reviews for AIWA yet.