Zanussi ZWG6120K Support Question
Zanussi ZWG6120K Support Question
Find answers below for this question about Zanussi ZWG6120K.Need a Zanussi ZWG6120K manual? We have 1 online manual for this item!
Question posted by darlingswtmined on March 22nd, 2015
The Pause Button Is Blinking But The Door Is Closed
The person who posted this question about this Zanussi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on March 23rd, 2015 8:02 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Could be a bad door sensor, timer or control board. You will have to have it looked at.
Related Zanussi ZWG6120K Manual Pages
Product Manaul - Page 2
... the appliance. • Keep all packaging away from children. • Keep all detergents away from children. • Keep children and pets away from the appliance door when it is not responsible if an incorrect installation and use causes injuries and damages. Risk of suffocation, injury or permanent disability.
• This appliance...
Product Manaul - Page 3
... sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
• Do not install the appliance where the appliance door can not be fully opened.
• Always be careful when you move the appliance again you move the appliance because it must be between 0,5 bar...
Product Manaul - Page 4
...of injury, electrical shock, fire, burns or damage to get closed in the appliance. Risk of injury or suffocation.
• Disconnect..., deactivate the appliance and disconnect the mains plug from the laundry.
• Do not put flammable products or items that ...the appliance.
• Do not touch the glass of the door while a programme operates.
Use
Warning! that there is necessary to...
Product Manaul - Page 5
...SEWERS
SEWAGE TREATMENT WORKS
TREATED DISCHARGE RIVER
1
2
3
1 Worktop
2 Detergent dispenser
3 Control panel
4 Door handle
5 Rating plate
4
6 Feet for treatment before being discharged safely into a river or stream ... that these instructions: • Set a programme without the prewash phase
to wash laundry with normal soil. • Always start a washing programme with the
maximum load ...
Product Manaul - Page 6
...; care symbol. 2 kg, 1000 rpm (ZWG 6100K), 1200 rpm (ZWG 6120K)
To rinse and spin the laundry. Washing indicator - End indicator
Washing programmes
4 Start/pause button (Start / Pause) 5 Super quick button (Super Quick)
6 Automatic spin reduction and Rinse hold button
7 Temperature button (Temp.)
Programme Temperature range
Cottons 90 °C - Cold
Cottons Eco
1)
60 °C - 40 °...
Product Manaul - Page 7
...
0.27
47
55
32
30
www.zanussi.com
7 All fabrics. 6 kg
Spin
To spin the laundry and to refresh. 3 kg, 700 rpm
Jeans 60 °C - The water temperature of laundry, the water and ambient temperature.
It prevents the laundry creases. 1 kg, 900 rpm
Refresh 20 30 °C
Synthetic and mixed fabric items. Light...
Product Manaul - Page 8
... consumption (kWh)
Standard cotton programmes
Standard 60 °C cotton
6
0.98
Standard 60 °C cotton
3
0.76
Standard 40 °C cotton
3
0.59
1) At the end of the laundry. Options
Programme
Super Quick1)
Extra Rinse
Delay Start
Cottons
∎
∎
∎
∎
∎
Cottons +Prewash
∎
∎
∎
∎
∎
Cottons Eco
∎
∎...
Product Manaul - Page 9
....com
9
To remove this button to delay the start button (Delay Start)
Press this function press the same buttons again. Set and start a programme for cotton at a
time. Open the appliance door. 2. Symbol - Open the water tap. 2.
Loading the laundry
1. Close the door. Make sure that no laundry stays between the seal and the door. Put a small quantity of...
Product Manaul - Page 10
...the flap is on. • the programme starts and the door locks
The appliance does a short spin at the start the ... for prewash phase directly into the compartments.
• Carefully close the detergent drawer.
The indicator of the set delay is ... the product in the recess.
10
When you start Press the Start/Pause button : • the indicator of the set a programme with the delay...
Product Manaul - Page 11
... the water. Press the button Start / Pause. tor flashes. 2. Press the button Start / Pause again.
Caution! Close the appliance door. 4. Press the button Start / Pause and the de-
To open the door.
vate the appliance. 2. Close the appliance door. 4. Set the programme again.
At the end of a programme 1. vate the appliance. 2. Remove the laundry from the appliance...
Product Manaul - Page 12
...• Divide the laundry in the appliance. Tie up pillowcases, close zippers, hooks and poppers. Turn the programme knob to to wash small items.
• A very small load can open the door. 4. Obey the ...find on the on the standby.
• All indicators go off.
• The indicator of button Start flashes slowly Press one of the washing programme, if you put the curtains in a washing ...
Product Manaul - Page 13
... products to remove limescales. Descaling
The water we use a water softener to remove rust particles from the laundry wash. Do this :
• Empty the laundry from the inner part. After each wash, keep the door open for washing machines.
www.zanussi.com
The inlet hose filter and the valve filter To clean the...
Product Manaul - Page 14
...red indicator of button Start / Pause flashes and one ... not occur or the appliance stops during operation. Remove the water inlet hose 4.
Close the water tap. 3. Possible solution Make sure that the appliance does not operate...Rinse : the appliance does not drain the water.
• End : the appliance door is installed in an area where the temperature can be less than 0 °C before...
Product Manaul - Page 15
...spin phase again. Make sure that the filter of the inlet hose and the filter of the water drain hose is closed. Make sure that the inlet hose has no damages. Make sure that the connection of the countdown.
Set the ...the valve are no kinks or bends. Problem
Possible solution
Make sure that the appliance door is correct.
Make sure that the button Start/Pause has been pressed.
Product Manaul - Page 16
... sure that the packaging and/or the transit bolts are removed.
Add more laundry in the correct position. The washing results are Increase the detergent quantity or use...instruction'. Use special products to a water tap with Make sure that you wash the laundry. Problem
Possible solution
Make sure that these data are available.
ately.
Refer to 'Installation instruction...
Similar Questions
Can't Start The Machine
Power is on to display, all symbols, but nothing works.
Power is on to display, all symbols, but nothing works.
(Posted by hughwolfson 10 months ago)
What Is The Difference Between The Start/pause Button And The On/off Button
(Posted by Ned7 2 years ago)
When I Switch On The Washer It Goes Straight Washing.
I can not set any settings and then in a few minutes it goes to end
I can not set any settings and then in a few minutes it goes to end
(Posted by davethatch 2 years ago)
Transit Bolts On Zwg6120k??
Where are they? Don't want to use the machine until we have found and removed - Zanussi customer sup...
Where are they? Don't want to use the machine until we have found and removed - Zanussi customer sup...
(Posted by meljsmith 10 years ago)