Zanussi ZDT11001FA Support Question
Zanussi ZDT11001FA Support Question
Find answers below for this question about Zanussi ZDT11001FA.Need a Zanussi ZDT11001FA manual? We have 1 online manual for this item!
Question posted by Naftacat on January 10th, 2017
The Device Doesn'the Turn On. Changed The Electronic Filter, No Turning On At Al
I found the device dead, with some water not discharged. No lights and no way to turn it on. Thought it was the electronic filter and replaced it. No signs of life. Is there a fuse I have to look for?
Current Answers
Answer #1: Posted by Troubleshooter101 on January 10th, 2017 6:35 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,030
Member since:
September 30th, 2015 Points: 2,927,030
What you need to do is remove the metal inspection panel at the front at the bottom below the door. As its built in you need to first remove the wooden plinth that runs at the bottom of the kitchen.
From there you will see the NTC in the white plastic sump bowl at the front. From memory it has a few thin blue wires going to it.
Remove this wiring block and see if theres any signs of corrosion on there. If so clean the block up and also give the NTC a clean were the wires go.
Then retry it and see what happens. You will need to cancel the error code by holding the start button in for several seconds.
Then retry the dishwasher and see what happens. If still the same then its either a faulty NTC which will need to be replaced or the control board is faulty.
To be honest its very rare we replace these NTC as they are quite good. We do see a lot of corrosion on the wires which can cause that but other then that you are looking at a faulty control board im afraid.
Let me know what you find or if you need anymore info just get back to me.
Regards
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Zanussi ZDT11001FA Manual Pages
Product Manaul - Page 2
...causes injuries and damages. The manufacturer is necessary to change the fuse in a household environment. • Do not change the specification of the appliance, carefully read the ...structures. The appliance has a 13 amp mains plug.
Electrical connection
Warning! jacent to the water supply. If not, contact an electrician. • Always use a correctly installed shockproof socket...
Product Manaul - Page 3
...you open door. • Dishwasher detergents are wet with flammable ...mains supply. • Cut off button 2 Programme lights
3 Indicators 4 Programme button.
3 Risk of it...water spray and steam to repair the appliance.
Model PNC Serial Number
1 Lower spray arm
2 Filters
9
3 Rating plate
4 Rinse aid dispenser
8
5 Detergent dispenser
7
12
6 Salt container
6
2
7 Water...
Product Manaul - Page 4
...
1,4-1,6
0,9 1,0-1,2
0,1
Water (l)
22-25
19-21
9 14-16
5
1) The water pressure and temperature, the variations of the mains supply, the options and the quantity of water and energy
consumption for test... Do not use of dishes can change the programme duration and the consumption values.
2) With this programme. You can wash a load with a fixed light.
• The programme indicator (B)...
Product Manaul - Page 5
... set level of the water softener agrees with the water hardness in your local water authority to confirm. You must adjust the water softener manually and electronically. Activating the acoustic signals...load the baskets.
Refer to the table to adjust the water softener to remove them. The dishwasher salt keeps the water softener clean and in the appliance. Wait until the ...
Product Manaul - Page 6
... button you fill it , after you fill the salt container, start a programme.
1
2
Turn the water hardness
dial to activate the appliance.
2.
Electronic adjustment
1. Press the programme button.
• The end indicator flashes intermittently. The number of flashes shows the level of water in setting mode. Press and hold the programme button until the programme...
Product Manaul - Page 7
...6. Make sure that the
items do not move freely before
you start the correct programme for dishwashers. M A X
M A X
A
+
2 34
1
2 34
1
+
1...Only use
1. Make sure that the spray arms can absorb water (sponges, household cloths).
• Remove remaining food from... load of rinse aid, turn the selector between position 1... cutlery basket. • Put light items in the rinse aid dispenser...
Product Manaul - Page 8
... and detergent residues can stay on if the rinse aid dispenser is in setting mode. 3. Adjust the water softener to the water hardness in compartment (B). Adjust the water softener to the lowest level. 2.
Use only detergents for dishwashers.
Combi detergent tablets These tablets contain detergent, rinse aid and other conditions, press and hold the...
Product Manaul - Page 9
...that there is completed, an intermittent acoustic signal operates. Press the on .
2. Dirty filters and clogged spray arms decrease the washing results. Wash the filter with water.
4 Remove filter (A). Warning! Cleaning the filters
C
B
A
1
2
A
3
To remove filters (B) and (C), turn the handle counterclockwise and remove. When you remove them . cator of interruption.
Make a check...
Product Manaul - Page 10
.... The water tap is lime- Replace the fuse.
The water tap is clogged or there is closed. Do not use neutral detergents. Troubleshooting
The appliance does not start .
Turn the handle.... If the holes in the fuse box is not connected in filter (A).
D
A
5
Put filter (A) to the appliance.
External cleaning Clean the appliance with water. First try to find a ...
Product Manaul - Page 11
... the items in the baskets is dishwasher salt in your area. Make sure that the position of the water softener is loose. programme continues from the point of load and soil.
The cap of the water softener agrees with a thin pointed object. Tighten the cap.
11
Water could not turn freely. The set level of...
Product Manaul - Page 12
... disposed of correctly, you add the correct quantity of electrical and electronic equipment. Voltage
220-240 V
Frequency
50 Hz
Water supply pressure
Min. / max. (bar / MPa)
(0.5 / 0.05 ) / (8 / 0.8 )
Water supply 1)
Cold water or hot water2)
max. 60 °C
Capacity
Place settings
12
1) Connect the water inlet hose to decrease
energy consumption. By ensuring this product is...
Similar Questions
Zanussi Dishwasher Not Starting
all the lights are working on my dishwasher but it won't turn on
all the lights are working on my dishwasher but it won't turn on
(Posted by obbiew 3 years ago)
The Detergent Tablets Are Not Solved After The Dishwasher Ends Its Cycle
Hi...I face this recurrent problem which is the detergent tablet is not solved after the end of the ...
Hi...I face this recurrent problem which is the detergent tablet is not solved after the end of the ...
(Posted by khaledh12345 4 years ago)
Where Dio I Find The Manual As This Part No Zdi12010xa Brings Up A Cooker
(Posted by roy17730 9 years ago)