Home » Yamaha » Audio Mixers » Yamaha EMX5014C

Yamaha EMX5014C Support Question

Find answers below for this question about Yamaha EMX5014C.
Need a Yamaha EMX5014C manual? We have 1 online manual for this item!

Yamaha Overview Questions Manuals Reviews Videos Research

Question posted by vikinval11 on February 9th, 2017

Yamaha Emx5014c

Power Cuts off immediately when switched on

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on February 11th, 2017 1:13 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,700

1,100
points

Check whether the vents at the front and rear of the unit are blocked. The EMX unit may overheat if the vents are blocked. If the unit overheats, the power may automatically go off. Wait for the unit to cool down, and then turn the power back on.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Yamaha EMX5014C Manual Pages

Owner's Manual - Page 3

... switches or connectors. (5)-4 EMX5014C Owner's Manual 3 If some trouble or malfunction occurs, immediately ...immediately turn off the power switch and disconnect the plug from the outlet, and have the device inspected by qualiﬁed Yamaha service personnel. • If this happens, turn off the power switch, disconnect the electric plug from the outlet. Even when the power switch...

Owner's Manual - Page 4

...Copying of commercially available music or other audio data for damage caused by using one... or registered trademarks of product. Utilize power outlets that interference will help beginners get...level of mixers and mixer concepts. Failure to follow instructions could void your Yamaha dealer. 4 EMX5014C Owner's ...switches, volume controls, and connectors, deteriorates over time.

Owner's Manual - Page 5

...28 2-channel connection ...28 2-channel parallel connection ...28 Rack Mounting 29 Setup ...30 Troubleshooting 31 Specifications 32 EMX5014C Owner's Manual 5 Please read through this Yamaha EMX5014C powered mixer. Contents Features ...6 Before Turning On the Mixer...6 ■ Mixer Basics Quick Guide ...7 Getting Sound to the Speakers ...7 Adding Some Reverb ...10 Using the Compressors to...

Owner's Manual - Page 6

... levels. High-Quality Digital Effects page 22 The mixer's internal effector is in between. This feature helps...of your choice. Internal Power Amp page 25 The internal amp makes it pops out. 6 EMX5014C Owner's Manual The rear ...stereo devices. Phantom Power (+48V page 25 A single switch turns phantom power on the rear panel. 3 Plug the power cord into a standard power outlet. ■...

Owner's Manual - Page 7

... as electric guitars and basses) directly to the appropriate input jacks on or off . And before turning the power to any device on the top panel. EMX5014C Owner's Manual 7 NOTE We recommend that you are powered off , be sure that all the way down. • Never connect both jacks to the same speaker...

Owner's Manual - Page 8

... dynamic microphones, however, as a keyboard or audio device, set the channel's switch to all other than condenser microphones to phantom power. If you have connected a microphone or other mic-level device, set the PHANTOM switch to the ON position ( ). • Be sure to leave this switch off the power to the mixer and to the ON ( ). For...

Owner's Manual - Page 9

...signal from the SPEAKERS jacks. EMX5014C Owner's Manual 9 Adjust the...switch on the power. 6 Turn on . 9 Set the ST Master fader to the "0" position. NOTE • To use the LEVEL meter to get an accurate reading of the ST Master fader. Adjust the GAIN controls so that LEVEL meter indication occasionally rises above the " " (0) level. If using . First turn on . Mixer...

Owner's Manual - Page 12

... RCA pin jacks are always unbalanced, and generally carry a linelevel signal at the most professional audio gear. If the corresponding circuitry is the "consumer connector," and the one that will also handle...at -10 dB, nominal. Male Female 12 EMX5014C Owner's Manual Mixer Basics Making the Most of Your Mixer An Introduction You've got yourself a mixer and now you're ready to use this...

Owner's Manual - Page 13

... unbalanced lines are fine-unless you're surrounded by power lines, motors, electric appliances, computer monitors, and ...device Unbalanced noise Noise Source Cable Receiving device EMX5014C Owner's Manual 13 How Do Balanced Lines ...Mixer Balanced, Unbalanced-What's the Difference? To summarize Microphones: Use balanced lines. one signal is ... While the desired audio...

Owner's Manual - Page 14

.... In most commonly used units in the owner's manual. + 20 dBu 0 dBu 0.775 V -20 dBu Most professional mixers, power amplifiers, and other conductors fluctuates. 2) A "hot" or "+" conductor which carries the normal-phase audio signal. 3) A "cold" or "-" conductor which carries the reverse-phase audio signal. The inputs and outputs on the panel or listed in...

Owner's Manual - Page 16

... lower. Cut for example, to come through. Surprisingly Guitar Trombone Trumpet enough, piano also has an incredibly powerful low end...LOW Flat MID Flat HIGH Boost HIGH Flat LOW Cut MID Cut Frequency (Hz) HIGH Cut 16 EMX5014C Owner's Manual the piano is playing solo. ...(i.e. The frequency of Your Mixer To EQ or Not to EQ In general: less is better. Mixer Basics Making the Most of ...

Owner's Manual - Page 17

... of music will have a significant effect on basically the same principle: a portion of the audio signal is primarily in the amount of delay time and feedback used as reverb or delay. Delay...of the mix. flanging uses longer delay times than time units. EMX5014C Owner's Manual 17 Mixer Basics Making the Most of Your Mixer Ambience Your mixes can be careful not apply too much reverb, ...

Owner's Manual - Page 20

...Switch (Channels 1 to 6) Pressing this button turns on /off. If you have connected a line-level device, such as a keyboard or audio device, set the switch...Yamaha YIC025, YIC050, or YIC070-as louder signals are TRS (tip, ring, sleeve) phone jacks that support bidirectional operation. The HPF cuts... of the switch setting, the mixer does not apply this switch in. Reference...EMX5014C Owner's Manual

Owner's Manual - Page 21

... 13/14) 100 Hz Maximum Cut/Boost ±15 dB 0 AUX Controls • AUX1 (PRE) This knob adjusts the channel's signal level into the AUX2 bus. If you switch the channel off , the mixer feeds the post-fader signal. G PFL (Pre-Fader Listen) Switch Set this switch on , the mixer feeds the pre-fader signal to...

Owner's Manual - Page 22

.... Reference Front & Rear Panels Digital Effects Section I J K L M N O 22 EMX5014C Owner's Manual I SEND Jack • EFF This unbalanced phone output jack outputs the signal ... to a cue box or other such monitoring system. NOTE The mixer saves the last value used with that type (regardless of the ...But note that channel pair to their defaults at power-off. You can then return the signal by ...

Owner's Manual - Page 23

...monitor signal to the PHONES jack. Reference Front & Rear Panels EMX5014C Owner's Manual 23 The internal effect is applied only if this switch on to feed the signal from the internal digital effect signal... the channel's PFL or AFL switch is ON, the channel's output is turned on. To set the switch on the mixer's power. As an alternative to the ON switch, you switch on , press it in so...

Owner's Manual - Page 24

... stereo phone-type output jack. ` U POWER Indicator The indicator lights up when the ampliﬁed signal output at the ST OUT jacks S, ST SUB OUT jacks R, and SPEAK- Each band can be sure to make appropriate level adjustments at all. 24 EMX5014C Owner's Manual The switch is for connection to a separately sold...

Owner's Manual - Page 25

...output the signal from the Stereo R bus. a ST/AFL-PFL Switch If the switch is set the switch on, the mixer supplies power to the XLR mic input jacks on all channels (the INPUT B ... Switch This switch turns Yamaha Speaker Processing on or off . EMX5014C Owner's Manual 25 Set this switch off if you do not need phantom power. • When using the AUX1 fader. The switch lights...

Owner's Manual - Page 30

... REVERB RESONANCE GATE TIME ASSIGN 1 CHORUS ATTACK VELOCITY ASSIGN 2 TEMPO RELEASE UNITMULTIPLY REMOTE ARPEGGIO R-AUDIO ON/OFF G-MIDI ON/OFF KN 1 LOW VOLUME 1 KN 2 LOW MID VOLUME 2 KN... Recorder Foot Switch (YAMAHA FC5) Headphones Microphones Microphones Effect processor (exciter) Drums Rear Panel 30 EMX5014C Owner's Manual Effect processor (delay) Power Amp Power Amp Subwoofer ...

Owner's Manual - Page 31

...problem, call Yamaha for service. (Refer to page 36 for a list of Yamaha dealers.) ■ Sound is correctly connected to the AC IN connector and plugged into a working power outlet. ■ Power suddenly went...cut off . ❑ Check whether the vents at the front and rear of the unit are blocked. Wait for the relevant channels are using the supplied power cord, and that the switches ...