Whirlpool WTW8800YC Support Question
Whirlpool WTW8800YC Support Question
Find answers below for this question about Whirlpool WTW8800YC.Need a Whirlpool WTW8800YC manual? We have 5 online manuals for this item!
Question posted by tharplogger on February 1st, 2016
The Inlet Water Valve Froze And Bursted I Replaced It And I Can't Get Any Power
to the controls on the machine. any suggestions?
Current Answers
Answer #1: Posted by majorapplirepair on February 3rd, 2016 4:44 AM
majorapplirepair
Member since:
October 7th, 2011 Points: 139,880
Member since:
October 7th, 2011 Points: 139,880
Water may have come in contact with the ECB (elec. control board) and shorted is out. Look at the ECB from the back and see if their is a little yellow light on inside it that should be glowing. If the light is on, you are getting power to the board. If you don't see this little light , replace the ECB.
Related Whirlpool WTW8800YC Manual Pages
Installation Guide - Page 2
...)
Flashlight (optional)
4" min (102 mm)
Adjustable or open-end wrench 9/16" (14 mm)
Wood block
Drain hose form
Cable Tie
Parts needed (Not supplied with washer):
Water inlet hoses (2)
Flat inlet hose washers (4)
Tape measure or ruler
Level
2 INSTALLATION REQUIREMENTS
TOOLS AND PARTS Gather the required tools and parts before starting installation.
Installation Guide - Page 3
...."
■■ Hot and cold water faucets located within 4 ft. (1.2 m) of where the power cord is your washer in low temperatures. See your washer to 1" (25 mm) diameter Standpipe... on all sides of the washer to support the washer weight (washer, water, and load) of the washer. Some water can remain in washer and can cause damage in a basement, laundry room, closet, or recessed...
Installation Guide - Page 4
...with a power supply cord having a 3-prong grounding plug.
■■ To minimize possible shock hazard, the cord must install higher than 96" (2.4 m) from bottom of washer. (...only this washer is recommended.
■■ This washer is recommended that a qualified electrician determine that may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub.
Floor...
Installation Guide - Page 5
... is secured with tape. CONNECT DRAIN HOSE
IMPORTANT: Proper connection of washer.
5 IMPORTANT: Do not force excess drain hose back into rear of the drain hose helps to avoid water leakage and damage to move the washer in the "Remove Shipping Base and Packing Ring" section. ■■ If foam shipping base has...
Installation Guide - Page 6
... note of the laundry tub. See "Tools and Parts" to the cold water faucet.
6 Washer must extend 4.5" (114 mm) beyond the form.
3. Connect inlet hoses to provide a gap for a few seconds through other side, anchoring form on valve when attaching to make sure that your water inlet hoses have flat washers at both ends.
Water should be secure but...
Installation Guide - Page 7
... by hand until it is snug. Use pliers to hot water inlet valve. Both hoses must be needed to check for leaks from faucet and at washer connection. If the washer rocks, minor adjustments may enter washer.
Check for future reference.
■■ Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are stable...
Installation Guide - Page 8
... and any tape remaining on washer. Press POWER.
Then turn the leveling foot clockwise to lower the washer or counterclockwise to complete one ...water faucets are on.
■■ Check for leaks around faucets and inlet hoses.
■■ Remove film from the washer tub for a medium-size load and pour it to raise the washer. Plug into detergent dispenser. Dispose of washer...
Energy Guide - Page 1
... Yearly Electricity Use
$12
Estimated Yearly Operating Cost
(when used with a natural gas water heater)
Your cost will depend on your utility rates and use.
• Cost ... per therm.
• For more information, visit www.ftc.gov/appliances (P/N W10405151)
Clothes Washer Capacity: Standard
Whirlpool Corporation Models: WTW8200Y*, WTW8240Y*,
WTW8400Y*, WTW8440Y*, WTW8600Y*, WTW8800Y*
Cat. ...
Use & Care Guide - Page 3
... not load garments directly over the center of detergent to thoroughly wet the load. Traditional agitator-style washer
Low-water washer
The most striking difference in the basket. Low-water washing creates excessive sudsing with your previous washer. Load garments in short pulses to use. Normal Sounds You Can Expect
At different stages of the...
Use & Care Guide - Page 4
...have set the dispensers for each cycle. Press and hold the button again. CONTROL PANEL AND FEATURES
1
2
3
4
5
Not all features and cycles are...laundry product is a preset cycle setting on all models.
1 POWER BUTTON Press to conserve energy and water. Not all options can be selected as cycle is specially designed to turn the washer ON. When this button to illuminate the washer...
Use & Care Guide - Page 5
... to the washer to maintain a minimum temperature.
Select a wash temperature based on the cycle selected.
NOTE: Fill dispenser with no warm water added, select Eco Cold. B
B Liquid chlorine bleach / Timed Oxi dispenser
Liquid chlorine bleach: This dispenser holds up . The bleach will be changed. This dispenser cannot dilute powdered bleach. Laundry boosters are...
Use & Care Guide - Page 9
...Washer Maintenance" for information on washer
Liquid chlorine bleach/ Oxi dispenser
Add liquid chlorine bleach or Oxi laundry...laundry boosters (liquid or powdered color-safe bleach), select the Oxi option, press the Dispensers button until Oxi is not necessary to dispense immediately into detergent dispenser. Low-water... based on your load size. Press POWER to use color-safe bleach or Oxi...
Use & Care Guide - Page 11
P ress START/PAUSE to begin
wash cycle
WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after every 30 washes: 1. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are available with Heater or Extra Rinse. NOTE: This washer does not include inlet hoses. OR If using liquid chlorine bleach, add 3/4 cup (180 mL) to reduce the...
Use & Care Guide - Page 12
... heavy blankets or towels into basket opening.
Drape power cord and drain hose over lid and down front of washer. Because some water may find laundry product residue leftover in your washer. If washer will not freeze. Place inlet hoses inside washer. Keep lid taped until washer is placed in washer or reconnect power. 3. Put 1 qt. (1 L) of time, follow WINTER STORAGE...
Use & Care Guide - Page 13
...suggested here or visit our website at www.whirlpool.com/help . Front and rear feet must be tight against the stainless steel basket. Avoid washing single items. Balance a single item such as expected
Not enough water in washer...not add more water to basket could be necessary to drainpipe or laundry tub.
Gurgling or humming Humming
Washer may hear the hum of water are properly ...
Use & Care Guide - Page 14
... detergent. Do not use HE detergent. Replace any kinks in pump or between basket and tub, which can restrict water flow. NOTE: If problems continue, contact...water is added. Washer may take 2 to possibly avoid a service call. This is power to run or fill, Check for proper water supply.
To remove suds, cancel cycle. Do not add more water to inlet valve. Both Hot and Cold water...
Use & Care Guide - Page 15
...and have both washer and faucet, and have water flowing to remove excess water.
Energy Star® qualified washers use cooler wash and rinse water temperatures than ...washer maybe clogged. Do not add detergent.
Check that inlet valve screens are not reversed.
Load not rinsed
Energy-saving controlled wash temperatures.
Check for your garment.
Make sure hot and cold inlet...
Use & Care Guide - Page 17
...washer. If the lid is connected to the cold water inlet. TROUBLESHOOTING
First try the solutions suggested... START/PAUSE. The washer is flashing and the machine has stopped, redistribute the...washer. If code appears again, call . If you experience
Possible Causes
Washer not performing as a basket of laundry, from locking.
Excessive suds in display
Objects on top of the washer...
Use & Care Guide - Page 18
... together for other rights that vary from state to state or province to province. WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is ... and you also may not apply to repair or replace appliance light bulbs, air lters or water lters. You must be provided by an authorized Whirlpool servicer is not available.
9.
Warranty Information - Page 1
... parts or systems resulting from unauthorized modi cations made to repair or replace appliance light bulbs, air lters or water lters. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. You...do not allow the exclusion or limitation of the Use & Care Guide. WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Water supply hookup - French door with exterior dispenser
...washer is available, contact an authorized plumbing technician. Side by side refrigerator Water supply hookup - If you begin. The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be a minimum of copper tubing into plastic water valve...to a water source or replacing the water filter, flush the water system. ... -
Display shows F20 or FH - Front-load washer
... operate with only one incoming source of the washer. Straighten the water inlet hoses. Inside the inlet valves are turned on ; Concentrated detergents labeled 2x and higher will shut off water to the washer to pause or cancel the cycle for a replacement set. NOTES: On some washers, when the washer is higher than 10 psi? You will... -
Water supply hookup - Bottom freezer/French door refrigerators
... on the water supply to reach water supply for 5 seconds. To connect to a water source or replacing the water filter, flush the water system. Slowly and evenly tighten the pipe clamp screws so the rubber washer makes a watertight seal. Place the free end of copper tubing into a container or sink. Remove plastic cap from the water valve inlet port. Do...
Similar Questions
Water Leaking From Bottom During Clean Cycle
I ran the Clean Cycle and had water leak from the bottom of the machine then reran Cycle Cycle and i...
I ran the Clean Cycle and had water leak from the bottom of the machine then reran Cycle Cycle and i...
(Posted by Jezeka31 5 years ago)
I Have Replaced The Bearing And The Starter And The Struts.
when I replace the bearings I replace the scatter I replace the struts now I'm getting a l code I've...
when I replace the bearings I replace the scatter I replace the struts now I'm getting a l code I've...
(Posted by mharmoning 7 years ago)
Water Valves Good ,runs In Spin,timer Moves,but No Filling Of Water
(Posted by shertyldenise 9 years ago)
How Do I Know If The Hot And Cold Water Valves Are Open
I see the valve and there is what appears to be a lock how do I know the lock is in the open positio...
I see the valve and there is what appears to be a lock how do I know the lock is in the open positio...
(Posted by bjrivera321 10 years ago)
Major Water Leak
Brand new, just installed and water is pouring from the top of the machine........how is this possib...
Brand new, just installed and water is pouring from the top of the machine........how is this possib...
(Posted by frank22994 12 years ago)