Home » Whirlpool » Laundry Washers » Whirlpool WTW7340XW

Whirlpool WTW7340XW Support Question

Find answers below for this question about Whirlpool WTW7340XW.
Need a Whirlpool WTW7340XW manual? We have 6 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by debraforeman on November 17th, 2011

Unbalanced Load

I am washing jeans and the washer became unbalanced I adjusted the load and now the washer will not restart. It just keeps beeping when I try to restart.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Whirlpool WTW7340XW Manual Pages

Dimension Guide - Page 1

Top Load Washer PRODUCT MODEL NUMBERS WTW6200V, WTW6500W, WTW6800W WTW6300W, WTW6340W, WTW7300X, WTW7340X, WTW7600X, WTW7800X, WTW7990X Electrical: A 120 volt, 60 Hz., AC only, 15- RECESSED AREA OR CLOSET INSTALLATION For closet installation, with a door, the minimum ventilation openings in the top and bottom of the washer. Laundry tub drain system (view C) The laundry tub needs a minimum...

Installation Instructions - Page 3

...clearance on sides. ■■ Additional spacing should be required for your washer to support the washer weight (washer, water, and load) of 315 lbs (143 kg). See "Electrical Requirements". ■■ ... equivalent ventilitation openings are required. Some water can remain in washer and can cause damage in a basement, laundry room, closet, or recessed area. To order, please refer...

Installation Instructions - Page 4

... a mating outlet is not available, it is the personal responsibility and obligation of the washer. 39" (990 mm) 28" (710 mm) Laundry Tub Floor The laundry tub drain system needs a minimum 20 gal. (76 L) capacity laundry tub. The top of the laundry tub must be at least 39" (990 mm) high and no higher than...

Installation Instructions - Page 5

... foam shipping base is necessary for proper operation and to move the washer in case you need to avoid excessive noise from top until end emerges. NOTE: Keep foam packing ring in the future. The drain hose is connected to your washer and is necessary to remove all shipping materials for proper operation...

Installation Instructions - Page 6

...standpipe (shown in the couplings. 2. Washer Insert new flat washers into a laundry tub, drainpipe, or bucket to ...laundry tub. Insert new flat washers For a laundry tub or standpipe drain, connect the drain hose form. See "Tools and Parts" to faucets or washer. Coupling B. Attach the hose labeled hot to avoid clogs. 2. IMPORTANT: To keep drain water from going back into the washer...

Installation Instructions - Page 7

... its final location. Move the washer to hot water inlet valve. Check for leaks Turn on valve when attaching to laundry tub leg, drain standpipe, or inlet hoses for leaks from faucet and at the factory. A small amount of water may be one that comes with an adjustable right front foot, lower the...

Installation Instructions - Page 9

...Check for a medium-size load and pour it to see what was skipped. ■■ Check that you have all of your washer, measure 1/2 of normal recommended amount of the washer. Press POWER. If there ...". ■■ To test and clean your tools. ■■ Keep the foam packing ring from the washer tub for future relocation of High Efficiency (HE) powdered or liquid detergent ...

Energy Guide - Page 1

U.S. Clothes Washer Capacity: Standard Whirlpool Corporation Models: WTW7340X*, WTW7600X*, WTW7800X* Cat. Government Federal law ... use. • Cost range based only on standard capacity models. • Estimated operating cost based on eight wash loads a week and a 2007 national average electricity cost of 10.65 cents per therm. • For more information, visit www...

Owners Manual - Page 3

... Efficiency." As the washer dampens and moves the load, the level of detergent to a traditional agitator-style washer. Cleaning with Less Water Washplate Traditional agitator-style washer Washer with your new washer is added. This low-water wash method uses less water and energy compared to use. Low-water washing creates excessive sudsing with dirty laundry, fill it evenly...

Owners Manual - Page 4

... the lid, press START/PAUSE. Overloading, unbalanced loads, or excessive suds may increase wrinkling in different energy and water usage. Each cycle, along with all models. 1 POWER BUTTON Press to select more damp. To use the warmest wash water safe for your laundry load. SOIL LEVEL Soil level (wash time) is locked and cannot be changed...

Owners Manual - Page 5

... on a dry load only and must be automatically diluted and dispensed at the optimum time when the Fabric Softener option is used, the wash cycle will use cooler wash water than the ... cycle. This dispenser cannot dilute powdered bleach. It will be selected before the washer has started on your main wash cycle. Use only High Efficiency (HE) detergent. The bleach will add additional ...

Owners Manual - Page 7

... settings for that best fits the load being washed. CYCLE GUIDE Settings and options shown in bold are available on fabric type. Use once a month to thoroughly clean the washer interior. This cycle drains the water and spins at a high speed. Spin speed is adjustable. After time has expired, washer will drain, but will not...

Owners Manual - Page 8

...; Turn knits inside out to your laundry 2. Load laundry into fabric. • Treat stains promptly. • Close zippers, fasten hooks, tie strings and sashes. Separate lint-takers from towels, rugs, and chenille fabrics. Try mixing different sized items to items during washing. Helpful Tips: • When washing water-proof or water-resistant items, load evenly. USING YOUR WASHER 1.

Owners Manual - Page 9

... High Efficiency detergents. NOTE: If using an Oxi laundry boost product, add to immediately dispense into washer. Overfilling dispenser will cause fabric softener to the detergent...non-HE detergent. Add HE detergent to turn on your load size. The package will be marked "HE" or "High Efficiency." Low-water washing creates excessive sudsing with liquid chlorine bleach. 9 Then select...

Owners Manual - Page 11

...wash cycle WASHER MAINTENANCE WATER INLET HOSES Replace inlet hoses after 5 years of hose failure. CLEANING YOUR WASHER Keep your washer as clean and fresh as Deep Clean or Extra Rinse. Using recommended AFFRESH® washer cleaner, add one tablet to washer... load unbalance. Water will pour into washer for more than 10 minutes the water will continue. To keep washer ...restart the cycle.

Owners Manual - Page 12

... are home. Unplug or disconnect power to locate, level, and connect washer. 2. CLEANING YOUR DISPENSERS You may stay in washer or reconnect power. 3. Because some water may find laundry product residue leftover in your washer. REINSTALLING/USING WASHER AGAIN To reinstall washer after non-use washer again: 1. Disconnect and drain water inlet hoses. 2. Drape power cord and...

Owners Manual - Page 13

... be in loose heaps evenly around basket wall. Avoid washing single items. Balance a single item such as coins could fall between basket and tub or may hear the hum of water for leaks (laundry tubs, drain pipe, water pipes, and faucets.) An unbalanced load can backup out of alignment and cause water to possibly...

Owners Manual - Page 15

...washes. The suds from regular detergent can slow or stop draining or spinning. Use only HE detergent. Washer may be tightly packed or unbalanced. Use cycle designed for loading recommendations. on load...TROUBLESHOOTING First try the solutions suggested here or visit our website at rinsing when load is tightly packed. Evenly arrange the wet load for your previous washer. Remove ...

Owners Manual - Page 16

... not add products directly onto load. Items may not have been followed. Additional water lifts the laundry off the impeller, resulting in water. See the "Cycle Guide" to measure correctly. Not washing like colors together and remove promptly after washer has started . See "Cleaning Your Washer" in pockets during wash to washer. Note that items will be...

Owners Manual - Page 17

...uL (unbalanced load) appears in display LF (too long to fill) appears in display Ld (too long to clear the code. If the dial is flashing, reselect your load. Check...laundry products dispensing too soon. It is normal for small amounts of water to be keeping the lid from the top of the cycle. To avoid, select a warmer wash temperature if possible, depending on load size. The washer...

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

The cycle time is not correct - Front-load washer
... see "Sud" and the Done status light is detected, the washer will increase. Unbalanced load conditions are washed in balancing the load. If an unbalanced load is on the incoming water temperatures, load size and type. The Estimated Time Remaining does not adjust for a long period of time, or jump to occur with a gentle...
Cycle time is not correct - Duet® Steam washer
... - Front-load washer Washer will glow while the washer is not able to zero? Does this problem. Cycle time is not correct - Do you see "Sud" and the Done status light is on some models) cycles, wash small loads to aid in balancing the load. If an unbalanced load is required. If you washing a large load in a Delicate...
Washer is not cleaning laundry - Top-load HE washer with Dispensers in Corners
... dispenser before laundering. To avoid dye transfer, unload the washer as soon as it online. Top-load HE washer with the washer. My Cabrio HE washer is normal for the Cabrio washer. This is not cleaning laundry. Do not add more detergent for washing heavy soils in the search tool below to the...