Whirlpool WTW4850XQ Support Question
Whirlpool WTW4850XQ Support Question
Find answers below for this question about Whirlpool WTW4850XQ.Need a Whirlpool WTW4850XQ manual? We have 5 online manuals for this item!
Question posted by stonefolks on November 9th, 2015
Pausing
How do I pause without it starting over?
Current Answers
Answer #1: Posted by Odin on November 9th, 2015 1:07 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Follow these instructions: http://www.manualslib.com/manual/266958/Whirlpool-W10338647a.html?page=4&term=pause
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool WTW4850XQ Manual Pages
Installation Instructions - Page 2
...starting installation.
Tools needed:
Parts needed: (Not supplied with washer)
Adjustable or open end wrench 9/16" (14 mm)
4" min (102 mm)
Level
Wood block
Ruler or measuring tape
Pliers that open to improve performance and minimize noise and possible "washer...proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 ...
Installation Instructions - Page 3
...° F (49° C). n Hot and cold water faucets located within 4 ft (1.2 m) of washer. Proper installation is not recommended. install no higher than 4.5" (113 mm) of washer. (Additional hoses may be inside standpipe or below 32° F (0° C). Top of laundry tub must install higher than 96" (2.44 m) from bottom of drain hose should...
Installation Instructions - Page 4
...start: remove shipping materials It is necessary to remove all shipping materials for proper operation. n Do not have the properly grounded outlet installed by a qualified electrician. Tip washer back and place on floor behind washer....
4
Remove shipping base
To avoid damaging floor, place cardboard supports from washer.
1. or 20-amp, fused electrical supply is adequate. n If codes...
Installation Instructions - Page 5
...form
Firmly grasp power cord plug and pull to move washer later.
4. For a laundry tub or standpipe drain, go to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from ... secure with separate directions. do not force excess hose into standpipe or lay on elbow end of washer.
4.5" (113 mm)
Place hose into standpipe (shown in Step 7. For a floor drain, remove...
Installation Instructions - Page 6
...washer. If you are found.
11. In most standard configurations, hoses will drain later.
6 Repeat with a red ring. Record hose installation or replacement dates for a few seconds through hoses into a laundry...replace hoses if bulges, kinks, cuts, wear, or leaks are only connecting to faucets or washer. 7. Remove drain hose form (floor drain installations only)
9. Do not use tape or ...
Installation Instructions - Page 7
... nuts clockwise on leveling feet tightly against washer cabinet. Level Washer
IMPORTANT: Level washer properly to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with a wood block or similar object that will support weight of washer about 1/2" (13 mm) from the washer cabinet. Recheck levelness of washer and repeat as a guide to prop up...
Installation Instructions - Page 8
...washer. Start washer and allow to see what was skipped. q Check that yellow shipping materials were completely
removed from console and any cycle.
q Read "Washer Use" in your tools. Select any tape
remaining on .
q Check that you have all parts are on washer. q Check that washer... detergent and pour it into washer basket or detergent dispenser (on some models). q Check for...
Dimension Guide - Page 1
... DIMENSIONS
271/2"
27"
(699 mm) (686 mm)
42" (1067 mm)
For closet installation, with equivalent air ventilation openings are minimum required. This washer has been tested for ease of laundry tub must be provided. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension...
Energy Guide - Page 1
U.S. Government
Federal law prohibits removal of
$1.218 per kWh and natural gas cost of this label before consumer purchase. Clothes Washer Capacity: Standard
Whirlpool Corporation Model: WTW4850X* Cat. V1as9DYA(3B)
Estimated Yearly Operating Cost
(when used with an electric water heater)
$15 ▼
$10
$71
Cost ...
Use & Care Guide - Page 3
...hear the motor turn the basket in component failures and noticeable mold or mildew. Cleaning with dirty laundry, fill it is normal for the best performance. Use only High Efficiency (HE) detergent. ... delivers detergent directly to the load size - For example, you start the cycle, the lid will lock, and the washer will begin the sensing process to thoroughly wet the load.
Automatic...
Use & Care Guide - Page 4
...washer has been paused the "wash" status light will start ...pauses that fabric softener is spinning, it may be added to the washer...washer. If the ...START/PAUSE/UNLOCK BUTTON Press to pause the cycle and unlock the lid.
press again to start over when the washer is on all features and options are different from traditional washers... is pressed, the washer will make a slight...
Use & Care Guide - Page 5
... again to open the lid, press START/Pause/Unlock. The sensing process will add water to move quicker during sensing. The lid will hear the motor and agitator moving the load. WASH
You will unlock once the washer movement has stopped. At the beginning of the sensing/wash cycle, water will turn on...
Use & Care Guide - Page 7
...during washing. NOTE: Always read and follow fabric care label instructions to avoid damage to your laundry
2.
Synthetics, knits, and corduroy fabrics will pick up lint from lint-givers. Add a ...to the bottom of the washer basket before adding clothes. Separate lint-takers from towels, rugs, and chenille fabrics.
If using an Oxi or color-safe bleach laundry boost product, add to...
Use & Care Guide - Page 8
...For best results, do not pack the load tightly.
Items need to move freely for correct amount of the basket. Load laundry into washer. Do not use more information, see "Cycle Guide". 3. Add liquid chlorine bleach
to dispenser
Turn cycle knob to reduce wrinkling...with liquid chlorine bleach.
8 Select cycle
IMPORTANT: Do not tightly pack or force items into washer
5.
Use & Care Guide - Page 9
...close lid and press START/Pause/Unlock again to start the wash cycle.
If your previous washer provided. When the cycle has finished, the DONE indicator will unlock once the washer movement has stopped. ...added to assist in soil removal and to add 1 or 2 missed garments: Press START/Pause/Unlock; If you need to help dissolve detergents. Filling is delayed for more than ...
Use & Care Guide - Page 10
... recommended amount of bleach to avoid damaging product over time. 3. To keep washer interior odor-free, follow these steps:
1.
If cycle must be interrupted, press START/Pause/Unlock twice and run washer on the label with a permanent marker. Press and hold the START/Pause/Unlock for about 30 seconds to mix antifreeze and remaining water.
3.
Put...
Use & Care Guide - Page 12
...floor, and washer must be attached and have started the washer. Feet may not be out of alignment and cause water to splash off basket if washer is not level. Washer may be...for leaks (laundry tubs, drain pipe, water pipes, and faucets.)
Improper loading can cause basket to be in washer drain system.
See "Using Your Washer" for proper installation:
Washer not level. Washer not performing...
Use & Care Guide - Page 13
... balanced spinning. Plug power cord into standpipe farther than cycles with a low spin speed. Reset a tripped circuit breaker. Washer will pause during certain phases of a service call...In U.S.A. Close lid and press START/Pause/Unlock.
The washer may not allow even distribution of the spins.
Load may hear the hum of the load in pump...
Use & Care Guide - Page 14
...wash action and spin speed; Both hot and cold water faucets must be on load after washer has started .
Heavy sand, pet hair, lint, and detergent or bleach residues may be attached to... using too much HE detergent. Always measure detergent and follow detergent directions based on load after washer has started . Select a cycle with air flow during the final spin. Add only 1 or 2 garments...
Use & Care Guide - Page 15
... fabric softener dispenser.
Undiluted bleach will not unlock until the basket has stopped spinning.
Not using the Start/Pause/Unlock button. Not washing like colors together and remove promptly after washer is complete.
See "Cleaning Your Washer" in the bleach dispenser. Use only HE detergent.
Wash like colors together. Use only liquid chlorine bleach...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How to remove odors from a front-load washer without a Clean Washer cycle
... necessary, the cycle may be interrupted by pressing the Pause/Cancel button once. This residue is soil that is damp, use a dehumidifier. Order your laundry room is programmed into the washer, but not shown on the washer console. Use of washer interior. If your Affresh washer cleaner See How to complete. The tablet... -
How to remove odors from front-load washer (for washers with stored program for cleaning washer)
...washer drum. If necessary, the cleaning cycle may reduce the effectiveness of buttons must be interrupted by pressing the Pause/Cancel button. However, this cleaning cycle. The tablet will not start...this cleaning cycle. If your control panel), see If your washer has a Clean Washer cycle (check your laundry room is not listed and doesn't have run a maintenance cycle. ... -
Not filling or not starting - Load-sensing Energy Star top-load washer with agitator.
... into a grounded three prong outlet. Are the water inlet valve screens on the water. Is the washer in a normal pause in the correct position. Is the water inlet hose kinked? The washer will not fill or start if the pointer is not in the cycle? Load-sensing Energy Star top-load...
Similar Questions
