Home » Whirlpool » Laundry Washers » Whirlpool WTW4800XQ

Whirlpool WTW4800XQ Support Question

Find answers below for this question about Whirlpool WTW4800XQ.
Need a Whirlpool WTW4800XQ manual? We have 5 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by byrdcool236 on November 11th, 2012

I Wtw4800xq1 Not Starting .i Change The Control Board Do Not Complete Cyc

i change the control board it take long to start take in water wash but do not commpleted cycle

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Whirlpool WTW4800XQ Manual Pages

Dimension Guide - Page 1

... change materials and specifications without notice. Wall standpipe drain system 14" max. (356 mm) 5" (126 mm) 17" (432 mm) 48 in.2 (310 cm2) 24 in door are required. Add spacing of 1" (25 mm) on the sides. Laundry tub drain system Minimum capacity: 20 gal. (76 L). Specifications subject to reduce noise transfer. This washer...

Installation Instructions - Page 2

... REQUIREMENTS Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area. 271/2" 27" (648 mm) (686... INSTALLATION REQUIREMENTS Tools and Parts Gather required tools and parts before starting installation. Tools needed: Parts needed: (Not supplied with washer) Your installation may require additional parts. n 8212656RP n 8212641RP ...

Installation Instructions - Page 4

...-amp, fused electrical supply is recommended. n Do not ground to the instructions included with local codes and ordinances. Remove shipping base. n This washer is equipped with a qualified electrician if you start: remove shipping materials It is recommended that a qualified electrician determine that a separate circuit breaker serving only this time. 4 A time-delay fuse...

Installation Instructions - Page 5

...to drain port Remove tape from washer lid, open lid and remove cardboard packing tray from tub Connect Drain Hose 5. Place drain hose in place on bottom of laundry tub. For a floor drain,... cord over side of drain hose should be used. 5 IMPORTANT: 4.5" (113 mm) of laundry tub. Drain hose form must be inside standpipe; do not force excess hose into standpipe (shown in Step...

Installation Instructions - Page 6

...water faucet. Connect inlet hoses to water faucets Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to check for leaks Turn on coupling by hand until it is connected to hot water to help in attaching hoses to remove the drain hose form from the end of water may need to washer... water faucet. Connect inlet hoses to washer Attach hose to water faucets...

Installation Instructions - Page 7

... beaded tie strap. Tighten leveling feet Jam nut With washer in its final location, place a level on feet until they are about 4" (102 mm) with wooden block. Level Washer IMPORTANT: Level washer properly to check levelness of washer and repeat as shown. Secure drain hose Laundry Tub Standpipe Wall 14. Use side seam as a guide...

Installation Instructions - Page 8

...complete full cycle. 8 q Read "Washer Use" in your washer, measure 1/2 of normal recommended amount of washer. q To test and clean your Washer User Instructions. If there is plugged into a grounded 3 prong outlet Complete Installation CHECKLIST q Check electrical requirements. q Check that yellow shipping materials were completely removed from console and any cycle. Start washer...

Owners Manual - Page 3

... Small will add a low amount of water for your fabric. • Warm and hot water will add the most cycles. FABRIC SOFTENER ADDED with EXTRA RINSE This option turns on both the Fabric Softener and the Extra Rinse options. 4 WASH CYCLE KNOB Use the Wash Cycle knob to start the selected cycle; The washer will hear the agitator moving the...

Owners Manual - Page 4

... Lid Lock light will come on . After draining and spinning out wash water, the washer will unlock once the washer movement has stopped. Press START/Pause/ Unlock again to open the lid, press START/Pause/Unlock. Some cycles use spray rinsing. Remove the load promptly for proper water removal, based on briefly (short hum) to move the basket...

Owners Manual - Page 5

...Use this cycle to complete a load after a power failure. Use this cycle to wash: Sturdy ...cycle or to drain washer after cancelling a cycle or completing a cycle after power interruption. High Combines a rinse and high speed spin for normally soiled cottons and mixed fabric loads. This cycle uses spray rinses only. After time has expired, water will drain, but the washer...

Owners Manual - Page 6

.... IMPORTANT: Follow the manufacturer's instructions to use. 6 Sort and prepare your garments. USING YOUR WASHER 1. Loose change, buttons, or any small object can pass under the agitator and become trapped, causing unexpected sounds. • Sort items by recommended cycle, water temperature, and colorfastness. • Separate heavily soiled items from lightly soiled. • Separate...

Owners Manual - Page 7

...or force items into washer 5. MAX FILL Dilute liquid fabric softener by filling the dispenser with warm water until the washer has completed filling, press the START/Pause/Unlock button to...wash cycle. Try mixing different sized items to spill, splash, drip, or run into dispenser; Do not allow liquid fabric softener to reduce tangling. load them in cycle. Load laundry into washer...

Owners Manual - Page 8

... garments: Press START/Pause/Unlock; Delay in soil removal and help dissolve detergents. Select options Select the load size setting most amount of water for your previous washer provided. Select TEMPERATURE 10. All rinses are using fabric softener, be added to save energy. If your faucet. Promptly remove garments after cycle has completed to restart...

Owners Manual - Page 9

..., do not wash clothes with the liquid fabric softener dispenser removed. Turn off both hands and squeezing, while pushing upward with a permanent marker. To winterize washer: 1. Select Normal Heavy cycle, hot Temperature, and large Load Size. 5. Water will pour into washer for 3 seconds to wipe up any spills. 2. Press and hold the START/Pause/Unlock for...

Owners Manual - Page 11

... nuts must be level to operate properly. Wash smaller loads to drainpipe or laundry tub. Avoid washing single items. Use Normal Regular cycle and Super or Large load size for proper installation: Washer not level. Water Leaks Check the following for any kinks in inlet hoses, which can restrict water flow. 11 Check that inlet valve screens...

Owners Manual - Page 12

... items after cycle has started to determine if load is normal. This is balanced. Washer not draining/ spinning, loads are still wet, or spin light remains on (indicating that the washer was unable to spin correctly, leaving the load wetter than 96" (2.4 m) above the floor. Cycles with lower spin speeds remove less water than cycles with a low...

Owners Manual - Page 13

... Canada www.whirlpool.ca If you experience Possible causes Solution Washer not performing as recommended. Both hot and cold water faucets must be clogged. See the "Cycle Guide" to the bottom of garments being washed. 13 Adding detergent on load after washer has started . This is tangling Washer not loaded as expected (cont.) Dry spots on top...

Owners Manual - Page 14

... Sharp items were in Washer Maintenance. Add only 1 or 2 garments after the cycle is complete to avoid dye transfer. See "Cleaning Your Washer" in pockets during wash cycle. Always follow garment manufacturer's care label instructions. The washer will not start or fill with dry items only. Use a higher soil level cycle option and warmer wash temperature to avoid chlorine...

Owners Manual - Page 15

... of purchase or installation date for product service if your complete model number and serial number. Consumable parts are unable to...to repair or replace appliance light bulbs, air filters or water filters. Service must provide proof of original purchase date ...30 days from the date of purchase. 6. WHIRLPOOL CORPORATION LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of ...

Warranty - Page 1

... so these limitations and exclusions may not apply to you . WHIRLPOOL CORPORATION LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this...date for Factory Specified Parts and repair labor to correct defects in your complete model number and serial number. Service calls to determine if another warranty applies...or water filters. You can be easily determined.

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Washer will not fill or start - Cabrio® washer with agitator
... add more items to not completely fill? Turn off throughout the wash. Is the Delay Wash status light on (on the water. Load-sensing Energy Star top-load washer with a cycle? Your washer will not fill or start . Does the water level seem too low, or does the washer appear to the load once the washer started . Plug power cord into a grounded...
Washer will not fill - Front-load Duet washer
... 1/2 inch will be completely submerged. The door may look closed for each load. Has a cycle been selected, but may not start after the last cycle? Press and hold START for leaks. This will not be less visible during certain cycles. Is Delay Wash status light on the washer clogged? The water level will not start a new cycle. This may take several...
Warm or hot wash temperatures are cooler than I expect - Top-load washer
... Cold and Cool water wash differences - Mixes in cold water to save energy is sensing how much cold and hot water to add to the washer to save energy. These temperatures may feel cold water entering my washer on a hot or warm fill? Your new washer uses a temperature control switch to control the amount of energy usage...