Whirlpool WTW4800XQ Support Question
Whirlpool WTW4800XQ Support Question
Find answers below for this question about Whirlpool WTW4800XQ.Need a Whirlpool WTW4800XQ manual? We have 5 online manuals for this item!
Question posted by rwiseAryaan on May 5th, 2014
Wtw4800xq Washer Won't Finish
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW4800XQ Manual Pages
Dimension Guide - Page 1
... or louvered door is recommended that a separate circuit serving only this washer be at least 39" (990 mm) high; Laundry tub drain system
Minimum capacity: 20 gal. (76 L).
Specifications subject... with product.
W10240509B 01/2011 or 20-amp, fused electrical supply is recommended. This washer has been tested for closet door ventilation openings which are for a standpipe drain: 2" ...
Installation Instructions - Page 2
...-blue steel couplings (2 pack)
Alternate parts: (Not supplied with washer)
Adjustable or open end wrench 9/16" (14 mm)
4" ...washer)
Your installation may require additional parts. Install your washer in the top of your washer to 19⁄16" (39.5 mm)
Optional tools:
Flashlight
Bucket
Parts supplied:
NOTE: All parts supplied for installation are in cardboard insert in a basement, laundry...
Installation Instructions - Page 3
... a closet door or louvered door is your responsibility. Top of standpipe must be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Installing on washer, and water pressure of washer.
See "Washer Care" in .2 (155 cm2)
1" (25 mm)
1" (25 mm)
3" (76 mm)
Dimensions show recommended spacing allowed, except for winterizing information.
This...
Installation Instructions - Page 4
...only this time.
4 Remove shipping base
To avoid damaging floor, place cardboard supports from washer.
1. IMPORTANT: Removing shipping base is equipped with local codes and ordinances. If a ...available, it at this appliance be in the neutral or ground circuit.
48" (1.2 m)
Move washer to within 4 ft (1.2 m) of the customer to the instructions included with a qualified electrician if...
Installation Instructions - Page 5
...a floor drain, remove the preinstalled drain hose form as shown. IMPORTANT: 4.5" (113 mm) of laundry tub. NOTE: Keep tray in place on bottom of drain hose should be used.
5
Free power... 7. Be sure to move washer later.
4. For a laundry tub or standpipe drain, go to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of laundry tub. See "Tools and Parts...
Installation Instructions - Page 6
... from the end of water may need to faucets or washer. Repeat this step with second hose for a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets
Run water ...until it is snug. A small amount of the drain hose. You may enter washer. Connect inlet hoses to washer
Attach hose to tighten couplings an additional two-thirds turn . Screw coupling by hand ...
Installation Instructions - Page 7
...they are about 4" (102 mm) with wooden block. HELPFUL TIP: You may want to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor. Adjust leveling feet
... up front of washer.
Check levelness of sides. Rock washer back and forth to reduce excess noise and vibration.
13.
Not Level
LEVEL
Not Level
7 12. Secure drain hose
Laundry Tub
Standpipe
Wall...
Installation Instructions - Page 8
... complete full cycle.
8 q Check that you have all of powdered or liquid detergent and pour it into washer basket or detergent dispenser (on .
q Check that all packaging materials. q To test and clean your Washer User Instructions. q Check that yellow shipping materials were completely
removed from console and any cycle. If there is...
Owners Manual - Page 2
WASHER SAFETY
2
Owners Manual - Page 3
... several minutes to most suitable for even distribution. Select a wash temperature based on your previous washer provided.
• E ven in the rinse for your laundry load.
press again to start the selected cycle; NOTE: If the washer is normal. These spins may be added to unlock the lid. WASH
You will be cooler...
Owners Manual - Page 4
... and moves the load. RINSE
You will continue to spin and spray in rinse water for the entire rinse time. SPIN
The washer spins the load at high speed. DONE
Once the cycle is locked and cannot be added if the Fabric Softener Added-Yes option was spinning ...
Owners Manual - Page 5
... fits the load being washed.
After time has expired, water will drain, but the washer will use for loads requiring an additional rinse cycle or to wash lightly soiled garments indicating...
High
Cycle Details:
Use this cycle to complete a load after a power failure. The washer will not spin.
Select Fabric Softener Added-Yes if using fabric softener. Also use intermittent...
Owners Manual - Page 6
..., rugs, and chenille fabrics. Separate lint-takers from lint-givers. If using an Oxi or color-safe bleach laundry boost product, add to the bottom of detergent to avoid pilling. Add a measured amount of detergent into fabric....; Mend rips and tears to avoid further damage to your laundry
2.
Add detergent
• Empty pockets.
USING YOUR WASHER
1. Sort and prepare your garments.
Owners Manual - Page 7
..., or use more than 1 cup (250 mL).
IMPORTANT: Do not tightly pack or force items into washer
5. Do not use more information, see "Cycle Guide".
7 For more than the recommended amount. 3....your load size. Turn cycle knob to spill, splash, drip, or run into dispenser; Load laundry into washer. Items need to move freely for correct amount of the cycle.
6. Then select Fabric Softener ...
Owners Manual - Page 8
...soils
8
Press the START/Pause/Unlock button to help dissolve detergent. When the cycle has finished, the DONE indicator will be added to assist in soil removal and help dissolve detergents. You....
8. the lid will be added to restart the cycle. This will unlock once the washer movement has stopped. 7.
Filling is the temperature from your load.
Dark colors that bleed ...
Owners Manual - Page 9
... due to water pressure surge. IMPORTANT: Do not add detergent. Rinse dispenser under warm water, then replace it will continue.
IMPORTANT: To avoid damaging the washer's finish, do not interrupt cycle. Unplug or disconnect power to wipe up any spills.
2. If storing or moving , or not using liquid chlorine bleach, add 1 cup...
Owners Manual - Page 10
... system and drain any remaining water into a pan or bucket. Unplug power cord.
5. Use half the manufacturer's recommended amount of washer. Shut off both water faucets.
2. Disconnect drain from back of washer.
4. Drape power cord over lid and down front of detergent for a medium-size load.
10 If you do not have...
Owners Manual - Page 11
... the bottom of the cabinet. In Canada www.whirlpool.ca
If you have water flowing to the washer.
See "Level the Washer" in washer drain system. Wash smaller loads to drainpipe or laundry tub.
Gurgling or humming
Washer may hear the hum of the sensing spins after you experience
Possible Causes
Solution
Vibration or Off...
Owners Manual - Page 12
...a cycle with high spin speeds.
Too much detergent causing suds to remove excess water. Washer will pause during certain phases of the load in pump or between basket and tub, ...packed or unbalanced loads may need to be tightly packed or unbalanced. See "Using Your Washer" for balanced spinning. TROUBLESHOOTING
First try the solutions suggested here or visit our website and...
Owners Manual - Page 13
...any kinks in hoses. The suds from operating correctly. Add only 1 or 2 garments after washer has started .
Reduce tangling by mixing types of load items. Use the recommended cycle for...the load being
selection. In Canada www.whirlpool.ca
If you experience
Possible causes
Solution
Washer not performing as recommended. Check for proper water supply.
Both hot and cold water faucets...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How do I regulate the flames sizes on my gas modular downdraft cooktop?
...160;a nonabrasive plastic scrubbing pad. Do not use a wooden toothpick. Acids may damage the finish. To adjust, change setting. If ports are noisy when turned off Do not allow foods... with a straight pin. Front-load washer The burner flames of the flames on cleaning products. IMPORTANT: Before cleaning, make sure all controls are uneven Washer continues to remain on food: Wash ... -
How do I clean the exterior porcelain enamel surfaces on my electric range?
... steel surfaces. Cleaning Method for Exterior Porcelain Enamel Surfaces (on some general cleaning tips for my electric range? Front-load washer Do not use our All Appliance Cleaner on my electric range? Here How do I clean the control panel on the .... These spills if left on cleaning products. Always follow label instructions on the appliance can damage the finish. -
What do I do about stains on my clothing when using my jetted sink?
... sink" section below. Rinse and wipe dry with hot water and add 2 tsp. (9.8 mL) of the finish with a mild, liquid detergent and a damp cloth or sponge. What do I do about stains on my ...jetted sink? then drain the jetted sink. Top-load washer Did you properly sort the load? These can be buffed or polished out of non-sudsing laundry detergent. Fill the jetted sink with a soft cloth....
Similar Questions
The Washer Won't Finish It's Cycle
my cabrio washer won't finish it's cycle . I'll try to rinse and drain but it stops 6 minutes before...
my cabrio washer won't finish it's cycle . I'll try to rinse and drain but it stops 6 minutes before...
(Posted by tonylcraig 8 years ago)
Washer Will Not Finish Any Load
My washer quits every load at the five minute mark. What gives?
My washer quits every load at the five minute mark. What gives?
(Posted by djaremko 13 years ago)