Whirlpool WGD94HEXW Support Question
Whirlpool WGD94HEXW Support Question
Find answers below for this question about Whirlpool WGD94HEXW.Need a Whirlpool WGD94HEXW manual? We have 4 online manuals for this item!
Question posted by Tricia1 on November 15th, 2012
How Many Btu's Does This Gas Dryer Use?
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WGD94HEXW Manual Pages
Owners Manual - Page 5
...savings.
n Remove lint and debris from the dryer. Use the NORMAL DRY dryness level to the dryer plays a big role in the dryer too long.
n On some models, the Quick... the Installation Instructions supplied with Steam Cycles. n Use of vent possible. Proper venting will be customized to efficiently dry laundry.
Under certain environmental or installation conditions, you may...
Owners Manual - Page 6
... models.
11-cycle models
2
1
3
4
5
8
7
8-cycle models
2 1
3
4
6 5
1 POWER BUTTON Press to turn the dryer on your laundry load. Press to stop/cancel a cycle at any time.
2 CYCLE CONTROL KNOB Use your dryer's cycle control knob to pause it.
4 TIMED DRY ADJUST for your dryer. See Cycle Guide for detailed descriptions of a Timed Dry or Quick Dry...
Owners Manual - Page 7
... allows you to dry completely. This will be displayed. Control Lock Use this button to lock the controls of the dryer and avoid an accidental change in process.
St appears in the load... settings will light up to 120 minutes of periodic tumbling to activate the EcoBoost option.
The dryer will be unable to remove a load immediately, press Wrinkle Shield to add up and the ...
Owners Manual - Page 8
... the preferred energy cycle.
Items need to rearrange items for all settings and options are available on all models.
Do not overload. do not overfill dryer drum.
Use the NORMAL dryness level to about 3/4 full.
Not all fabrics. This cycle is a long cycle with 3-4 items, not more than 1/4 full.
Work clothes, casual...
Owners Manual - Page 9
...:
Shirts, blouses,
Quick Refresh
Medium
12 (15)* Wrinkle Shield†
and slacks
with Steam (on some models).
Large load: Fill the dryer drum up to Medium heat setting may be used for drying medium-weight items such as towels and work clothes.
Not all models.
Temperature Dryness Level Garment # Cycle Signal for...
Owners Manual - Page 14
... only: Close shutoff valve in the
Installation Instruction. Use tape to faucet.
Unplug dryer or disconnect power. 2. To Use the Dryer Again 1. Turn on vacation or not using your dryer for an extended period of time, you will not freeze. Plug in dryer or reconnect power as described in gas supply line. 3. Disconnect power. 2. If you should: 1. Clean...
Owners Manual - Page 15
... is open . The exhaust vent is normal. For gas dryers, make sure that the valve on dryer is used in dryer. The thumping sound should be turning, but you may vibrate if not properly installed.
Use 4" (102 mm) diameter vent material.
Incorrect power supply.
Use a time-delay fuse. Electric dryers require 240-volt power supply. The water pump...
Owners Manual - Page 17
... and return to avoid overdrying the load.
If the message persists, consult a qualified electrician. variable service codes.
Select a Timed Dry heated cycle, and restart the dryer.
Using Timed Dry cycle with a lower heat setting to the estimated time remaining. To remove odors left in the Installaton Instructions for details.
"AF" (low airflow...
Dimension Guide - Page 1
Gas Dryer
PRODUCT MODEL NUMBERS
WGD94HEX, WGD95HEX, WGD97HEX, WGDXXHEX
Gas supply: This dryer is equipped for planning purposes only. gas.
Do not overtighten. Exhaust venting: Exhaust your dryer to change without notice. Rigid or flexible metal exhaust vent must be used for exhaust vent with the National Fuel Gas Code ANSI Z223.1. Vent system chart: NOTE: Side and bottom...
Installation Instructions - Page 4
.... Check existing electrical supply and venting. Check that
(new vent installations)
opens to LP gas
Parts supplied: Parts package is a registered trademark of Saturn Fasteners, Inc.
4
Rubber washers...174; TORX is located in your installation. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■■Vent elbows and ductwork Additional...
Installation Instructions - Page 5
... Requirements."
■■A separate 15 or 20 amp circuit for a gas dryer or 30 amp circuit for ease of dryer to water and/or weather. If not level, clothes may not tumble properly and automatic sensor cycles may cause dryer not to your Use and Care Guide for information about accessories available for your local...
Installation Instructions - Page 6
...or Service" section of gas dryers:
■■Mobile Home Installation Hold-down Kit Part Number 346764 is within reach of dryer's final location.
4-wire receptacle (14-30R)
If using a replacement power supply ...;■Additional clearances might be required for wall, door, floor moldings, dryer venting, and gas line.
■■Additional spacing should be considered on both sides of...
Installation Instructions - Page 7
... phone numbers referenced in doubt as to convert the appliance from the gas specified on the rating plate in a risk of your gas company.
7 This dryer is recommended. SAVE THESE INSTRUCTIONS
GAS TYPE Natural Gas:
This dryer is properly installed and grounded in your Use and Care Guide. No attempt shall be made by CSA International for...
Installation Instructions - Page 8
... be easy to flare adapter fitting C. 1/8" NPT minimum plugged tapping D. 1/2" NPT gas supply line E.
Gas supply pressure testing
■■The dryer must be used . Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to the gas supply line with the standard for connectors for lengths under 20...
Installation Instructions - Page 9
... brushing on the corner posts until diamond marking is no kinks. valve is open when handle is parallel to finish turning legs until it is used, be used to connect dryer to existing gas line. Correct any leak found.
†®TEFLON is shown. Non-flared male fitting
Remove red cap from...
Installation Instructions - Page 10
....
■■ Remove excess to seal all governing codes and ordinances. Dryer exhaust must be connected into interior of duct and catch lint. NOTE: If using an existing vent system, clean lint from ground or any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of the system and make sure exhaust...
Installation Instructions - Page 14
... outlet and inside exhaust hood. Once dryer is in dryer. Connect vent to crush or kink vent or flexible gas line. Adjust leveling legs
If dryer is not level, prop up using a wood block, use wrench to exhaust hood with a 4" (102 mm) clamp.
2. Dryer vent must be level for levelness. Move dryer to final location
Check levelness of...
Installation Instructions - Page 15
...q Check that you live in a hard water area, use of a water softener is
recommended to see what was skipped. q Check dryer's final location. q If you have all of the ...all parts are on dryer.
q Check to
remove any tape remaining on . The odor will not start dryer. q Be sure the water faucets are now installed.
See "Level Dryer". Gas Models
q Plug into ...
Installation Instructions - Page 16
.... 8" long Torx® T25 screwdriver
#2 Phillips screwdriver
1. Remove inner door from outer door
IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from dryer
Using a Torx®† T25 screwdriver, remove the 2 screws securing the door strike to the outer door...
Installation Instructions - Page 19
... the 4 Torx® T25 screws removed earlier.
19 Reinstall door on dryer
Using a Torx® T25 screwdriver, remove the 4 screws on the hinge into the mounting slot and slide down to the outer door.
10. Insert the tabs on the dryer. Reinstall inner door assembly
Bottom of the door facing up. Reinstall the...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Cycle is too short - Dryer
... TM cycles use sensing strips inside the dryer drum to large loads. Electric dryer Dryer does not ...using a dry rack with a dry rack. Automatic Dry or Accudry cycles determine the length of the cycle by sensing the moisture in a Automatic Dry or Accudry cycle? Are you drying a small load in the load as the wet load items pass over the sensor strips. Gas dryer... -
Damp loads or long drying times - Dryer
... exhaust hoods allow for the longest exhaust vent systems. Use the fewest number of this a new installation? Make sure that the louvers or flapper door easily open and close. Were you drying a large load? Gas dryer If the dryer is above 45°F (7°C). A dryer softener sheet may be removed from moving out of... -
My dryer makes sounds or vibrations
..., pens, or similar items may be tumbling in the dryer can download a manual for your particular model by using the search feature below. My dryer makes sounds or vibrations Is there a clicking sound? (Gas dryers only) The gas valve clicking on is not used for a while, there may be a light thumping sound during washing...
Similar Questions
Start Button Gas Dryer Model Wgd9600ta
The start button of my Whirlpool gas dryer popped out. It seems that the little plastic knob can not...
The start button of my Whirlpool gas dryer popped out. It seems that the little plastic knob can not...
(Posted by fchart47 7 years ago)
Covert To Lp Gas
The whirlpool dryer is WSD91HEXW I H=NEED TO CONVERT TO LP GAS , NEED PARTS
The whirlpool dryer is WSD91HEXW I H=NEED TO CONVERT TO LP GAS , NEED PARTS
(Posted by WPJL73 11 years ago)
Dryer Lint
I want to clean out the lint trap area of my dryer. How can I access it? It does not have the remova...
I want to clean out the lint trap area of my dryer. How can I access it? It does not have the remova...
(Posted by sunflwrgurly 11 years ago)
