Whirlpool WFW94HEXW Support Question
Whirlpool WFW94HEXW Support Question
Find answers below for this question about Whirlpool WFW94HEXW.Need a Whirlpool WFW94HEXW manual? We have 5 online manuals for this item!
Question posted by tousfcs on May 28th, 2014
Does The Whirlpool Washer Wfw94hexw2 Have A Lint Screen
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WFW94HEXW Manual Pages
Dimension Guide - Page 1
... install no higher than 96" (2.44 m) from bottom of washer. (Additional hoses might be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Wall standpipe drain system
41/2" (113 mm)
4"...washer only):
39" min. (990 mm) 1" (25 mm)
34" min. (864 mm)
3" (76 mm)
48 in.2 (310 cm2)
41/2" (113 mm)
Minimum diameter for planning purposes only.
Because Whirlpool...
Installation Instructions - Page 2
...Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835
Lint clogged drain
Drain Protector Part Number 367031 Connector Kit Part ...Guide. INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before starting installation.
Alternate parts: (Not supplied with washer)
n 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
n 8212641RP 5 ft. (1.5 m) Inlet ...
Installation Instructions - Page 3
...990 mm) 1" (25 mm)
4" (102 mm)
1" (25 mm)
1" (25 mm)
3
Installing on washer, and water pressure of washer to weather or in temperatures below 32° F (0° C). n Floor must be exposed to reduce noise ... arrangement, consider allowing more space for ease of 315 lbs (143 kgs). See "Washer Care" in low temperatures.
n A level floor with water and load) of installation...
Installation Instructions - Page 4
... mm) from bottom of standpipe must be at least 30" (762 mm) above floor; Top of washer. install no higher than 96" (2.44 m) from bottom of washer. See "Alternative Parts". Floor standpipe drain system
41/2" (113 mm)
Laundry tub drain system
41/2" (113 mm)
min. 30" (762 mm)
Minimum capacity: 20 gal. (76...
Installation Instructions - Page 6
...
If clamp is transported at later date, call your local service center to avoid suspension and structural damage, a certified technician must properly set up washer for relocation.
6 For a laundry tub or standpipe drain, go to back of drain hose, slide it over bolt holes with a 13 mm (1/2") wrench. Pull bolts and plastic...
Installation Instructions - Page 7
... form from the end of drain hose should run until it is connected to hot water to the washer.
10. NOTE: Both hoses must be supplied to help in picture) or over each other when ...installations, you will cross over side of laundry tub. do not force excess hose into a laundry tub, drainpipe, or bucket to inlet valves.
You may need to faucets or washer. Do not use tape or sealants ...
Installation Instructions - Page 8
..., go to Step 18. Record hose installation or replacement dates for leaks
Remove cardboard from beneath washer.
Secure drain hose
Laundry Tub
Standpipe
Wall
4.54".5" (113 mm)
4.5" (113 mm)
4.5" (113 mm)
Grip washer from side to laundry tub leg, drain standpipe, or inlet hoses for leaks. Secure drain hose to side.
If all four...
Energy Guide - Page 1
... loads a week and a 2007
national average electricity cost of 10.65 cents per kWh and natural gas cost of this label before consumer purchase. Clothes Washer Capacity: Standard
Whirlpool Corporation Model: WFW94HEX* Cat. U.S.
Use & Care Guide - Page 4
See "Cycle Guide" for your laundry load. Steam models
2
1
3
4
5
8
7
9
C
B
6
D
A HE detergent
B Liquid fabric
A
softener
C Chlorine bleach
D Oxi Dispense
Non-Steam models
1
2
3
4
5
... off. Press to stop/cancel a cycle at any time.
2 WASH CYCLE KNOB Use your washer.
Turn the knob to select available cycles on all features and cycles are available on your Wash...
Use & Care Guide - Page 8
... remover products on load type and cycle, the washer can be marked "HE" or "High Efficiency." Low-water washing creates excessive sudsing with a regular non-HE detergent.
For multiple items, use . Use only HE detergent.
Separate lint-takers from towels, rugs, and chenille fabrics. Load laundry into fabric. See "Cycle Guide" for the...
Use & Care Guide - Page 9
...an
Oxi product. This is normal.
3. Use only High Efficiency (HE) detergent.
Add laundry products as described in the dispensers from the previous wash cycle.
For powdered detergent, slide the... dispenser
HE detergent compartment
Pour a measured amount of HE detergent into the washer too early. If you may add powdered or liquid oxi-type boosters or color-safe bleach...
Use & Care Guide - Page 13
... cycle is empty.
2. To avoid odors, leave the door open slightly, to avoid odor and rusting of washer interior. Make sure laundry drum is finished
Promptly remove garments after the wash cycle is selected, the washer will take up any garments in the dispensers after cycle has completed to allow for small items...
Use & Care Guide - Page 14
.... If stained areas are found, wipe down these areas of dispenser with guides in washer, then slide dispenser back into slot.
d) W ipe down on dispenser. 7. Inspect...using a damp cloth. IMPORTANT: Wear rubber gloves when cleaning for foreign objects. WASHER MAINTENANCE
CLEANING THE DISPENSER
You may find laundry product residue leftover in warm, soapy water, using 3/4 cup (177 mL) of...
Use & Care Guide - Page 16
...and have been removed. This code may be on. Door not closed for at www.whirlpool.com/help for service. F#E# code other than as described above the floor.
Use only ...call for assistance and to clear the code. Washer is pressed. Always measure detergent, and base detergent quantity on load size and soil level. Inlet valve screens on . Drain hose extends into standpipe farther ...
Use & Care Guide - Page 17
...floor for optimal cleaning.
17 See "Remove transport bolts from washer" in washer drain system. This is properly secured to drainpipe or laundry tub.
Check that the drain hose is normal. Always ... during "Add A Garment." First try the solutions suggested here or visit our website at www.whirlpool.com/help for assistance and to possibly avoid a service call for service to remove items.
It...
Use & Care Guide - Page 18
... feature periods of cycle.
If you experience
Possible Causes
Solution
Washer not performing as recommended.
Check that inlet valve screens have water flowing to run or fill, Check for proper water supply.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help for assistance and to continue.
Use & Care Guide - Page 19
...unlock Incorrect or wrong wash or rinse temperatures
Warm* selection not available
Water remaining in washer after cycle.
Remove any clogs from regular detergent or using too much detergent can slow ... Check that inlet valve screens are not reversed. For best performance, not all cycles. First try the solutions suggested here or visit our website at www.whirlpool.com/help for assistance ...
Use & Care Guide - Page 20
...not rinse well if tightly packed.
Inlet valve screens on . Remove any kinks in water.
The suds from regular detergent can cause the washer to improve cleaning.
Use only HE detergent. Always... cleaning. Not choosing the right cycle for each cycle. Items need to unload the washer at www.whirlpool.com/help for each cycle.
Select a slower spin speed.
If safe for tough ...
Use & Care Guide - Page 21
.... Avoid overfilling. The transfer of dye can occur if washer is complete.
First try the solutions suggested here or visit our website at www.whirlpool.com/help for washing heavy soils in Washer Maintenance . Sharp items were in a load. Items may have tangled. Unload washer as soon as cycle is tightly packed. Always follow...
Use & Care Guide - Page 22
... use powdered or liquid laundry boosters in washer.
Load dispensers before starting a cycle. Use only liquid chlorine bleach in dispenser at www.whirlpool.com/help for proper ... single item such as expected (cont.)
Solution
Incorrect dispenser operation
Clogged dispensers or laundry products dispensing too soon. The Quick Wash cycle is detected.
Overfilling causes immediate ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Display shows AF - Dryer
... only 4" diameter heavy metal exhaust vent material. Larger or smaller diameter material will reduce good air movement and cause longer drying times. Is the lint screen clogged with rigid or flexible heavy metal vent. A clogged exhaust vent system slows moist air from leaving the dryer and extends drying time. Box or... -
Lint is on the load - Dryer
... with darks. Over time, residue may build up on my dryer load. lights with lights and darks with lint? Clean the Lint Screen Is the lint screen clogged with your dryer cycle descriptions for information on the load - My dryer makes sounds or vibrations Fabric is hard to... -
Damp loads or long drying times - Dryer
.... Dryer Is the exhaust vent or outside exhaust hood to be too cold for Best Performance How Auto Dry and Timed Dry Work Is the lint screen clogged with a rigid or flexible heavy metal vent. Replace any fabric softener sheets from the inside the dryer drum. This slows moist air...
Similar Questions
My Dryer Wfw70heb Needs New Lint Screen. The Models Listed Are Slightly Differen
the model numbers I have to not end with 'w'
the model numbers I have to not end with 'w'
(Posted by Edises1 7 years ago)
W10219016 Maytag Lint Screen Spring Doors. Help In Replacing.. Thank You!
(Posted by mgiammetta 9 years ago)
How To Clean Pump Filter On Front Loading Whirlpool Washer Wfw94hexw
(Posted by HQajowas 10 years ago)
How To Repair Review Front Cover On Front Loading Whirlpool Washer Wfw94hexw
(Posted by cuongcla 10 years ago)