Weider Pro 9640 Support Question
Weider Pro 9640 Support Question
Find answers below for this question about Weider Pro 9640.Need a Weider Pro 9640 manual? We have 1 online manual for this item!
Question posted by frankuchler on April 20th, 2021
Where Do I Go To See Replacement Parts For The Joe Weider 9640 Pro?
I am looking for a replacement cable for the leg lift on my weider 9640 pro.
Current Answers
Related Weider Pro 9640 Manual Pages
User Manual - Page 1
... AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE.
If you have questions, or find that there are missing or damaged parts, we are committed to you complete satisfaction through direct assistance from our factory. Model No. WESY96400 Serial No.
User Manual - Page 2
... from state to state. WEIDER is limited in connection with...fitness for a particular purpose is a registered trademark of ICON Health & Fitness, Inc. Remove the PART IDENTIFICATION CHART and the PART...CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this warranty is limited to replacing...
User Manual - Page 3
...Replace any exercise program, consult your hands away from moving parts. ICON assumes no responsibility for protection.
4. Keep small children and pets away from the home gym system when performing an exercise that could become pinched between the leg... any worn parts immediately.
11. This is in any time while exercising, stop immediately and make sure that the cables remain on ...
User Manual - Page 4
...further, please review the drawing below and familiarize yourself with the parts that are labeled. The PRO 9640 offers a selection of weight stations designed to achieve the specific ...If you for selecting the versatile WEIDER® PRO 9640 Home Gym System. Military Press Arm
Backrests
Press Arm
Leg Lever
Low Pulley Station
Foot Plate
Weight Stacks
Leg Press Plate
4
To help ...
User Manual - Page 5
... arm assembly, 3) cable and pulley assembly, 4) seat and backrest assembly, and 5) VKR assembly. Note: Some small parts may have read the following tools: A socket set, a set of open the parts bag labeled "FRAME ASSEMBLY...
• As you assemble the PRO 9640 be sure that all parts are oriented as shown in the drawings.
• Tighten all parts of the PRO 9640 in a cleared area and remove ...
User Manual - Page 6
... yet. FRAME ASSEMBLY
4 1
42 6
3
6 2. Press a 1" Square Inner Cap (6) into the Leg Press Upright (56).
Do not tighten the Nylon Locknuts yet. Hand-tighten four 5/16" Nylon Locknuts (3) onto...two 2" Square Inner Caps (27) into the Front Upright (42). Slide the VKR Upright (74) and the Leg Press Upright (56) onto the indicated 5/16" x 2 1/2" Carriage Bolts (1) in the Base (4).
3
Hand...
User Manual - Page 7
...(27) into the top of the crossbar.
27
Attach the Top Frame (55) to the VKR Upright (74) and the Leg Press Upright (56) with two 5/16" x 2 3/4" Bolts (11), two 5/16" Flat Washers (8), and two 5/16...the end
4
of the Rear Seat Frame (100) to tip either stack of Weights.
Be careful not to the Leg Press Upright (56) with two 5/16" x 2 3/4" Bolts (11) and two 5/16" Nylon Locknuts (3).
...
User Manual - Page 9
...there is a Bushing (98) in the Leg Press Arm
(96). The Plastic Bushings should fit on this side
59-Lubricate
21
Welded Spacers
90 ...Lubricate the 3/8" x 8" Bolt (59). 9.
Lubricate a 3/8" x 3 1/4" Bolt (67). The Leg Press Arm must be on each end of holes in each welded spacer on the side shown. Locate and open the parts...
User Manual - Page 11
...
88
Ball
15
Hook
84
23-79" 58-147" 72-194"
99-63"
11
Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS."
16
During steps 16 through 36, refer to verify proper cable routing.
Attach the Military
15
Press Arm (84) to the VKR
Upright (74) with
two 5/16" x 2 1/4" Bolts...
User Manual - Page 13
... the 3 1/2" Pulley (15) shown in the groove of several pre-
24
attached parts.
Reattach the 3 1/2" Low Pulley (76), with a 3/8" x 2" Bolt (12) and a 3/8" Nylon Locknut (21). Be sure that the Cable Trap is inside the Long "U"Bracket. Be sure that the Cable is in the inset drawing. Be sure that the 3/8" x 3 3/4" Bolt (88), the...
User Manual - Page 18
... the Bolt. Locate and open the parts bag labeled "SEAT ASSEMBLY."
Attach the top of the Seat to pivot.
96
12
11
3
8 99
94
75
15 21
100 93
SEAT ASSEMBLY
37. Wrap the Leg Press Cable (99) around a 3 1/2" Pulley (15). Slide the end of the Leg Press Cable (99) onto the end of the...
User Manual - Page 20
... same manner.
45 78 10
74 80
81
3
43 10 79
78 77
VKR ASSEMBLY
20 Insert a Pad Tube (28) into the Leg Lever (29).
Locate and open the parts bag labeled "VKR ASSEMBLY."
Press two 3/4" Round Inner Caps (34) into the ends of the Pad Tube.
29 30
30 34
28...
User Manual - Page 21
... remove it to be sure that all parts have been properly tightened. If one of this manual. Before using the home gym system, pull each cable a few times to the Front Upright (42) under the "WEIDER" nameplate as shown.
46
WEIDER Nameplate 42 PRO 9640
Decal
47. IMPORTANT: If the cables are not properly installed, they may...
User Manual - Page 22
...part of the exercise will be reduced. Refer to the exercise poster accompanying this manual to see how the home gym system should be performed. If there is any slack in the cables or chain as an exercise...
The PRO 9640 features two weight stacks. Use the WEIGHT RESISTANCE CHART on
page 24 to be attached between the Lat Bar and the Low Cable with two Cable Clips.
For some exercises, the...
User Manual - Page 23
...exercises, the Seat (13) must be removed.
Align the welded tubes on Leg Press Plate and the holes in the Leg Press Arm (96). Attach the Seat Frame to the leg lever.
Re-insert the Press Pin (97) through the welded tubes on the Leg Press Plate (95) with a Cable... a Cable Clip (53). ADJUSTING THE LEG PRESS PLATE
Remove the Press Pin (97) from the Seat Frame (36). Lift the Seat...
User Manual - Page 25
...
15 12
2
23 or 99
2 72
71 2
58
71 2
3
The Military Press Cable (72) can be tightened in the cables before resistance is in one of the Low Cable (23) to be replaced, see ORDERING REPLACEMENT PARTS on the home gym system, can be lifted off the pulleys often, it . If there is felt when using the...
User Manual - Page 28
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at the center of the product (WEIDER® PRO 9640 Home Gym System).
3. Part No. 135891 F04109-C R1296A
Printed in Canada © 1996 ICON Health & Fitness, Inc. Mountain Time (excluding holidays). The NAME of this manual).
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the...
User Manual - Page 29
... shipping purposes. Please Note: The assembly is divided into five stages: 1) frame assembly, 2) arm assembly, 3) cable and pulley assembly, 4) seat and backrest assembly, and 5) VKR assembly. If you identify the small parts used in assembly.
Important: Some parts may have been pre-assembled for assembly. WAIT UNTIL YOU BEGIN EACH ASSEMBLY STAGE TO...
User Manual - Page 32
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL!
81
User Manual - Page 33
... x 2 1/2" Plastic Bushing 1" x 7/8" Plastic Bushing Rubber Bumper 1/4" x 2 1/2" Carriage Bolt 5/16" Nylon Jam Nut Press Bracket Leg Press Plate Leg Press Arm Press Pin Bushing Leg Press Cable Rear Seat Frame Pivot Arm User's Manual Exercise Poster
Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. WESY96400
R1296A
Key No. Qty.
1
10
2
6
3
34...
Similar Questions
I Need To Order A Part For Weider Pro 9925
I need to order the part where the weight sits
I need to order the part where the weight sits
(Posted by Joubbj 1 year ago)
Parts For Weider Pro 3750 Where To Get Them ?
Needing part number 85 high cable
Needing part number 85 high cable
(Posted by slyguy61520 2 years ago)
I Need To Order Some Parts For My Weider Pro 9640.hilm
(Posted by corineremon 3 years ago)
Weirder Pro 575 Replacement Cables
where can I order the replacement cables for this machine.
where can I order the replacement cables for this machine.
(Posted by Lilhoss 3 years ago)
Having Trouble Routing Cable For The Fly Machine Part.
(Posted by djr1418 9 years ago)