Weider 8775hard Drive Sys Support Question
Weider 8775hard Drive Sys Support Question
Find answers below for this question about Weider 8775hard Drive Sys.Need a Weider 8775hard Drive Sys manual? We have 1 online manual for this item!
Question posted by Rallison12 on July 19th, 2013
Pulley Problem
No longer have the assembly instructions. Can't get the pulleys to work properly.
Current Answers
Related Weider 8775hard Drive Sys Manual Pages
English Manual - Page 1
... DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. Read all safety precautions and instructions in this owner's manual before using this owner's manual for future reference.
Save this equipment.
...-06,,
',GA •
"..E6
MULTI-STATION • 'PROFESSIONAL QUALITY FITNESS SYSTEM
Model No. WG87750 Serial.No. CUSTOMER HOT LINE: 1-800-225-0653 Mon.-Fri., 6 a.m.-6 p.m.
English Manual - Page 2
...bar from the hard drive sy tem when performing an exercise that could cause the hard drive system to the rear weight stack is being used at all of the pulleys.
13. Keep ... pre-existing health problems. Read all instructions in the accompanying literature before using . Replace any exercise program, consult your physician. The feet of the person using the hard drive system.
1. If...
English Manual - Page 3
...ASSEMBLED DIMENSIONS: Height: 74 inches Base: 90 inches x 75 inches
Vertical Knee Raise (VKR) Arm
Lat Bar High Pulley Station
Selector Knob Arms
Military Press/Squat Arm
Military Press Seat
Rear Weight Stack Front Weight Stack
0 Foot Plates
Ab Arm Leg Lever Low Pulley...number and serial number before using the WEIDER 8775 Hard Drive System.
To help you to develop every major muscle ...
English Manual - Page 4
... is on the same side of the Center Upright as you assemble the HARD DRIVE System, make sure that all parts are oriented exactly as grease or petroleum jelly...'s manual.
As you attach them, unless instructed to the Stabilizer (16) with two 5/16" x 2 3/4" Bolts (122), 1 1/4" x Rectangular Washers (148), and 5/16" Nylock Nuts (4).
2. To simplify assembly, the following tools (not included) are ...
English Manual - Page 7
...
53
18
107
a'IIo
c1.1:4
19 112 " 4
15
9. Slide the Ab Upright (97) onto the 3/8" x 2 3/4" Bolt (55) and the two indicated 5/16" x 2 1/2" Carriage Bolts (1) in assembly steps 7 through 9.
9 143
4
/ 12 Metal Eyelet
a,
O
19
97
1 555
4:\14 4
16 1
7 8.
English Manual - Page 8
... Front Upright (19) with four 1/4" x 3/4" Screws (7), 1/4" Flat Washers (6), and 1/4" Nylock Nuts (5).
11 Attach the Bar Holder (58) to the axles on the Front Upright (19). Assemble the Left Arm (27) to
the horizontal position.
8
24
143 41 49
105 64 Do not overtighten the Nut;.the Selector Plate
must bend downward...
English Manual - Page 17
... that the cables move smoothly, locate and correct the problem before using the hard drive system, test the cables and pulleys. Before using the hard drive system. The use of all parts are not properly routed, they may be explained in the drawing below.
42 HIGH PULLEY
WEIDER 8775
VKR
"NA
U- Pull each cable a few times...
English Manual - Page 18
...Bracket (22) is touching the Weights, and turn the bent end downward.
tion, the low pulley station and the arms; The weight setting of either the butterfly mode or the press mode. ...one of the three holes in the correct starting position for each exercise. ADJUSTMENT
The instructions below describe how each part of the hard drive system can be adjusted to any slack in increments of 12.5...
English Manual - Page 19
...2 3/4" Bolt (113) through the Seat Frame and the Front Upright. For some exercises, the Chain (73) should be attached between the Lat Bar and the Pulley Cable so the Lat Bar is not attached to the 5/16" x 2" Eyebolt... Strap (125) can be attached in the correct starting position for the exercise to be attached to the Pulley Cable (69) with two Cable Clips. Attach the other end of the Chain...
English Manual - Page 20
...to be performed.
74
The Nylon Strap (125) can be attached between the Lat Bar and the Pulley
cp
74
Cable so the Lat Bar is in the same manner.
20 Adjust the length
of the... Chain between the Lat Bar and the
73 69
Pulley Cable with a
Cable Clip (74). tion for the exercise to the Pulley Cable (69) with two Cable Clips. For some exercises, the Chain (73) should be attached in the...
English Manual - Page 21
... worn parts immediately. Do not use the hard drive system.
Follow the instructions below . Reassemble the parts. Pull the end of the Pulley Cable until there is no slack in the cables before resistance is not too tight, or the top weight on the hard drive system, can be lifted off the weight stack...
English Manual - Page 24
...IS IN LIEU OF ANY AND ALL OTHER WARRANTIES AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO THE TERMS SET FORTH ...part(s) from defects in Canada The KEY NUMBER and DESCRIPTION of the product (WEIDER® 8775 Hard Drive System).
3. This warranty extends only to replacing or repairing, at WEIDER's option, the product at ...
Similar Questions
I'm In Need Of A #47 Pulley For My Gym How Do I Get Some Extra Pulley Weider 289
In in need of a#47 pulley for my weider home gym what are some replacement I can get
In in need of a#47 pulley for my weider home gym what are some replacement I can get
(Posted by smoak72 1 year ago)
How To Install Cable And Pulley On Weider Pro 4850
can you help me install new weider pro 4850 cable and pulley?
can you help me install new weider pro 4850 cable and pulley?
(Posted by verrolburnett 8 years ago)
Pulley Assembey F
How to assemle pulley on model no. 8530 Butterfly, press and squat exercise
How to assemle pulley on model no. 8530 Butterfly, press and squat exercise
(Posted by Sarge24509 8 years ago)
Weider Pro 8900 Pulley Position/tension.
Pulley's 3-6 do not seem to be set up correctly. I have them exactly as they are in the book, howeve...
Pulley's 3-6 do not seem to be set up correctly. I have them exactly as they are in the book, howeve...
(Posted by djbillbraun 11 years ago)